WS-7034U Wireless 433 MHz Temperature Station Instruction Manual
TABLE OF CONTENTS Topic Quick Setup Inventory of Contents Detailed Setup Guide Battery Installation Setting the Time Selecting Units of Measurement Features Minimum and Maximum Temperatures Resetting Minimum and Maximum Temperatures Adding additional remote temperature sensors (optional) Mounting Troubleshooting Maintenance and Care Specifications Warranty Information Page 3-5 6-7 8 9-10 10 11 12 13-14 15-16 17-18 19 20-21 22-25 2
QUICK SETUP Hint: Use good quality Alkaline Batteries and avoid rechargeable batteries. 1. Have the indoor temperature station and remote temperature sensor 3 to 5 feet apart. 2. Batteries should be out of both units for 10 minutes. 3. Place the batteries into the remote temperature sensor first then into the indoor temperature station. (All remote temperature sensors must be started before the indoor temperature station) 4. DO NOT PRESS ANY BUTTONS FOR 10 MINUTES.
display will show both the indoor temperature and an outdoor temperature. If the indoor temperature station does not display both temperatures after the 10 minutes please retry the set up as stated above. After both indoor and outdoor temperatures are displayed for 10 minutes you can place your remote temperature sensor outdoors and set your time. The remote temperature sensor should be placed in a dry, shaded area. The remote temperature sensor has a range of 80 feet.
NOTE: Fog and mist will not harm your remote temperature sensor but direct rain must be avoided. To complete the set up of your indoor temperature station after the 10 minutes have passed please follow the steps on pages 8-9. INVENTORY OF CONTENTS 1. The indoor temperature station (Figure 1) 2. The remote temperature sensor (TX6U) and mounting bracket. (Figure 2) 3. 3 each, 1/2” Philips screws. 4. One strip of double sided adhesive tape. 5. Instruction Manual and Figure 1 Warranty Card.
ADDITIONAL EQUIPMENT (not included) 1. 1 Philips screwdriver. 2. 2 Fresh AAA Alkaline batteries. 3. 2 Fresh AA Alkaline batteries DETAILED SETUP GUIDE Battery Installation 1. Install 2 AA batteries in the remote temperature sensor. Make sure they do not spring free, or start-up problems may occur. 2. Install 2 AAA batteries in the indoor temperature station. Do not press any buttons for at least ten minutes.
Setting the Time 1. Press and hold the “SET” button for 5 second, “12h” will appear in the TIME LCD. 2. Press and release the “MIN/MAX” button to select either 12h time (am/pm) or 24h time 3. Press and release the “SET” button 2 times, the hour will flash in the upper left corner. 4. Press and release the “MIN/MAX” button to set the hours 5. Press and release the “SET” button to move to the minute setting 6. Press and release the “MIN/MAX” button to set the minutes. 7.
If there is no display here it is AM. Make sure you set the time accordingly. Selecting Units of Measurement 1. Press and hold the “SET” button for 5 second until “12h” or “24h” appears in the TIME LCD. 2. Press and release the “SET” button again, “°F” will appear in the TIME LCD. 3. Press and release the “MIN/MAX” button to shift between °F and °C. 4. Press and release the “SET” button twice to activate settings. FEATURES Minimum and Maximum Temperatures 1.
2. The recorded minimum temperature is 3. 4. 5. 6. displayed. The time of the minimum outdoor temperature will also flash. Press the “MIN/MAX” button, “MAX” appears next to the indoor and remote temperatures. The recorded maximum temperature is displayed. The time of the maximum outdoor temperature will also flash. Press and release the “MIN/MAX” button to exit min/max mode. To view optional additional sensors, press and release the “SET” button while viewing the minimum or maximum.
Adding Additional Remote Temperature Sensors (optional) The WS-7034U is able to receive signals from 3 different remote temperature sensors. Following are some brief instructions for the basic set-up of remote temperature sensor units with the WS-7034U. These extra remote temperature sensors can be purchased through the same dealer as this unit, or by contacting La Crosse Technology directly.
indoor temperature station and do not press any buttons for ten minutes. Transmission problems will arise if this is not done correctly. To view the temperature of a different remote temperature sensor unit, press and release the “SET/CH” button. A shift from one number to the next should be observed in the OUTDOOR LCD. MOUNTING Note: To achieve a true temperature reading, avoid mounting in direct sunlight. We recommend that you mount the remote temperature sensor on a North-facing wall.
Remote Temperature Sensor 1. 2. 3. Remove the mounting bracket from the remote temperature sensor. Mount the bracket in the desired location with either screws or adhesive tape. Reattach the remote temperature sensor into mounting bracket. Indoor Temperature Station The indoor temperature station comes with the table stand already mounted. If you wish to use the table-stand all that is required is to place the indoor temperature station in an appropriate location. 1. 2. 3.
temperature station over the screw and pull down to secure. TROUBLESHOOTING NOTE: For problems not solved, please contact La Crosse Technology via e-mail or phone, or visit our website, www.lacrossetechnology.com Problem: The LCD is faint Solution: Replace batteries Problem: No outdoor temperature is displayed. Solution: 1. Remove all batteries, reinsert into remote temperature sensor first, then into the indoor temperature station. 2.
so the straight-line signal is not passing through more than two or three walls. Problem: Temperatures do not match if units are placed next to each other. Solution: Each temperature sensor is manufactured to be accurate to within 1 degree plus or minus and under normal conditions, so two sensors could be as much as 2 degrees different. However, the difference can be exaggerated further because the sensors are designed for different working environments.
is difficult to compensate for the above factors and obtain an accurate comparison. MAINTENANCE AND CARE INSTRUCTIONS • • • • • Extreme temperatures, vibration, and shock should be avoided to prevent damage to the units. Clean displays and units with a soft, damp cloth. Do not use solvents or scouring agents; they may mark the displays and casings. Do not submerge in water. Do not subject the units to unnecessary heat or cold by placing them in the oven or freezer.
SPECIFICATIONS Transmitting 433MHz Frequency Measuring Temperatures Indoor 32°F to 156.2°F with 0.2 Temperature °F resolution. Station (0°C to 69.0°C with 0.1°C resolution). Remote -21.8 °F to 156.2°F with Temperature 0.2°F resolution. Sensor (-29.9°C to 69.0°C with 0.1°C resolution). Temp accuracy +/- 1°F (+/- .5°C). Transmitting Maximum 80 feet (25m) range open space. Temperature check Indoor Every 10 seconds. Outdoor Three times in 10 minutes. Batteries—(Alkaline recommended) Remote 2 x AA, 1.
Sensor Indoor Temperature Station 2 x AAA, 1.5V Dimensions: (L x W x H) 2.36 x .88 x 5.90 in. Indoor (excluding table stand) Temperature (60 x 22.5 x 150 mm). Station 2.32 x 0.86 x 2.55 in. Remote (59 x 22 x 65 mm). Temperature Sensor Battery life Approximately 1 year. WARRANTY INFORMATION La Crosse Technology provides a 1-year warranty on this indoor temperature station. Contact La Crosse Technology immediately upon discovery of any defects covered by this warranty.
This warranty does not cover any defects resulting from improper use, unauthorized repairs, faulty batteries, or the indoor temperature stations inability to receive a signal due to any source of interference. LA CROSSE TECHNOLOGY WILL NOT ASSUME LIABILITY FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF THIS INDOOR TEMPERATURE STATION. THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR PUBLIC INFORMATION. THIS PRODUCT IS NOT A TOY.
Phone: 608.782.1610 Fax: 608.796.1020 e-mail: support@lacrossetechnology.com (warranty work) sales@lacrossetechnology.com (information on other products) web: www.lacrossetechnology.com FCC DISCLAIMER This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Freq. 433.
FCC ID: OMO-01RX (Receiver), OMO-01TX (transmitter) THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1. THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND 2. THIS DEVICE MUST ACCEPT INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.