Setup Guide

ManualsBrandsLa Crosse ManualsAlarmsLa Crosse W85923

INTRODUCTION:

The Projection Alarm Clock features manual set time with projection,

12-hour/24-hour option, time alarm with snooze, indoor temperature with

minimum and maximum readings all in a simple, easy-to-read display.

PROJECTION ALARM CLOCK

SETUP INSTRUCTIONS STEP-BY-STEP:

STEP 1:

• Insert the 4.5 volt AC power adapter into the designated area on the

back of the Projection Alarm Clock.

• Insert the power adapter plug into a wall outlet for a continuous

backlight and projection.

• The Projection Alarm Clock will light up and show indoor temperature

and time (12:00).

STEP 2: (battery-backup operation for power outages)

• Remove battery cover from Projection Alarm Clock, slide tab down

and pull out to remove the cover.

• Insert 2 NEW AAA batteries (not included) into the back of the

Projection Alarm Clock. Observe the correct polarity (see marking

inside the battery compartment).

• Note: Backlight and projection will not display constantly when

operating on battery power. They will appear for 3 seconds when the

SNOOZE/LIGHT button is pressed.

• Do Not Mix Old and New Batteries

• Do Not Mix Alkaline, Standard, Lithium or Rechargeable

Batteries

PROGRAM MENU:

TIME SET: Be sure the Time is showing or

press and release the MODE button to move

to Time Mode.

• 12/24 HOUR TIME: With time displayed,

hold the SET button and 12Hr will flash.

Press and release the UP or DOWN button

to select 24Hr. Confirm with the SET button and move to the hour.

• HOUR: The hour will flash. Press and release the UP or DOWN

button to select the correct hour. Confirm with the SET button and

move to the minutes.

• MINUTES: The minutes will flash. Press and release the UP or

DOWN button to adjust the minutes. Confirm with the MODE button to

exit time set.

CALENDAR SET: From Time Mode, press and release the MODE

button twice to move to Calendar Mode. The

year will show in the time area.

• YEAR: Hold the SET button to enter

Calendar Set. The year will flash. Press and

release the UP or DOWN button to select the

correct year. Confirm with the SET button

and move to the month.

• MONTH: The month will flash. Press and release the UP or DOWN

button to select the correct month. Confirm with the SET button and

move to the date.

• DATE: The date will flash. Press and release the UP or DOWN button

to select the correct date. Confirm with the MODE button to exit

calendar set.

Note: The weekday will set automatically as you set the year, month

and date.

ALARM SET: From Time Mode, press and

release the MODE button once to move to

Alarm Mode. The alarm time will show in the

time area and the letters AL will show next to

the temperature.

• ALARM HOUR: Hold the SET button to enter Alarm Set. The hour will

flash. Press and release the UP or DOWN button to select the correct

hour. Confirm with the SET button and move to the minutes.

• A

LARM MINUTES: The minutes will flash. Press and release the UP

or DOWN button to adjust the minutes. Confirm with the MODE button

to exit.

ALARM ON/OFF:

Press and release the MODE button to move to Alarm Mode (AL).

• ON: With the Alarm time showing, press and release the UP button to

activate the alarm. When the alarm is active the alarm icon will

display in the upper left corner.

• OFF: With the Alarm time showing and alarm is active, press and

release the UP button to deactivate the alarm. The alarm icon will not

appear when the alarm is inactive.

SNOOZE:

• When the alarm sounds, press the SNOOZE/LIGHT button to trigger

snooze alarm for 4 minutes. The snooze icon Zz will flash after the

hour.

• Press any button to turn off the snooze feature when the snooze

alarm sounds. The snooze icon will disappear.

BACKLIGHT:

• Battery Power: Press and release the SNOOZE/LIGHT button on the

top of the projection clock to show the backlight for 3 seconds.

Note: Backlight will not display constantly when operating on battery

power.

• A/C Power: Backlight is displayed constantly.

PROJECTION:

TIME will project continually when operating with the a/c power cord.

YEAR will project for about 30 seconds when in Calendar mode.

ALARM TIME will project for about 30 seconds when in Alarm mode.

TIME YEAR ALARM

• Battery Power: Press and release the SNOOZE/LIGHT button to

show the projection for 3 seconds.

Note: Projection will not display constantly when operating on battery

power.

• A/C Power: Projection is displayed constantly.

Focus Projection: Use the focus wheel on the back of the

projection arm to focus the projection image. Aim the

projection on the wall or ceiling 2-6 feet away for best

projected image.

Projection Alarm Clock

with Indoor Temperature

Model: W85923 | Quick Setup Guide

Summary of content (2 pages)

PAGE 1
Projection Alarm Clock with Indoor Temperature Model: W85923 | Quick Setup Guide INTRODUCTION: The Projection Alarm Clock features manual set time with projection, 12-hour/24-hour option, time alarm with snooze, indoor temperature with minimum and maximum readings all in a simple, easy-to-read display. PROJECTION ALARM CLOCK SETUP INSTRUCTIONS STEP-BY-STEP: STEP 1: • Insert the 4.5 volt AC power adapter into the designated area on the back of the Projection Alarm Clock.
PAGE 2
• Projection Arm: The projection arm will rotate 180 degrees to allow you to project on the wall or ceiling. Adjust the focus of the projection with the focus wheel on the back of the projection arm. Projection Arm Rotates FAHRENHEIT/CELSIUS: From a normal display (time showing), press and release the SET button to switch from Fahrenheit to Celsius. MAX/MIN RECORDS: • VIEW: Press and release the MAX/MIN button to view the minimum then maximum indoor temperature.