Data Sheet

Input
Router
1
(Mute)
Input
Router
2
(Mute)
Input
Mixer A
Input
Mixer B
EQ Delay
EQ Delay
Crossovers
Output Routing
AMP
Attenuator
Mute
Phase Rev
Attenuator
Mute
Phase Rev
Attenuator
Mute
Phase Rev
LoadSmart
SpeakerSafe
LoadSmart
SpeakerSafe
LoadSmart
SpeakerSafe
LoadSmart
SpeakerSafe
Amp Gain
Amp Gain
Amp Gain
Amp Gain
Attenuator
Mute
Phase Rev
Module:
Gain
Phase Rev
Mute
Analog 1/2
AES 1
AES 2
Dante X
Dante Y
Analog 1/2
AES 1
AES 2
Dante X
Dante Y
AMP
AMP
AMP
ISVPL
ISVPL
ISVPL
ISVPL
Module:
Gain
Phase Rev
Mute
Output EQ
LimiterMax
RMS / Peak
Module Output:
Gain/Delay
Phase Rev
Mute
Output EQ
LimiterMax
RMS / Peak
Module Output:
Gain/Delay
Phase Rev
Mute
Output EQ
LimiterMax
RMS / Peak
Module Output:
Gain/Delay
Phase Rev
Mute
Output EQ
LimiterMax
RMS / Peak
Module Output:
Gain/Delay
Phase Rev
Mute
Output EQ
LimiterMax
RMS / Peak
Module Output:
Gain/Delay
Phase Rev
Mute
Output EQ
LimiterMax
RMS / Peak
Module Output:
Gain/Delay
Phase Rev
Mute
Ser. N:o
Removed!
CH 2
CH
1
CH 4
CH 3
CLASS 3 WIRING
SPEAKER OUTPUTS
INPUT 1 INPUT 2LINK
1 LINK 2
AES/EBU
INPUT 1-2 LINK 1-2
LINK SECPRIMACT LINKACT
SWITCHED 10/100 Base-TX
Must be grounded/earthed
Made in Sweden
PIN 1: SCRN 2: POS 3: NEG
ANALOG WITH ISO-FLOAT
TM
200-240V 2500W
50-60Hz
PLM 0000Q1
Ser. N:o
Removed!
SPEAKER OUTPUTS
INPUT 1 INPUT 2LINK
1 LINK 2
AES/EBU
INPUT 1-2 LINK 1-2
LINK SECPRIMACT LINKACT
SWITCHED 10/100 Base-TX
Must be grounded/earthed
Made in Sweden
PIN 1: SCRN 2: POS 3: NEG
ANALOG WITH ISO-FLOAT
TM
200-240V 2500W
50-60Hz
PLM 0000Q
1
The front panel is the “local control center” for the PLM 10000Q. An intuitive, menu driven interface allows quick access to key functions using
the moisture resistant silicone touchpad. Information is clearly displayed on the daylight-readable, 2.5-inch LCD panel. The soft-button keypad
and precision rotary encoder provide control of processing and amplication functions, with key lock available.
The PLM 10000Q is available with either binding posts or an “embedded patch panel” with Neutrik speakON connectors (2 x NLT4 and
1 x NLT8). Common connectors include; 2 x analog input XLR with switchable Iso-Float, 2 channels of AES/EBU with link-through capability for
daisy chaining, 2 x EtherCON
®
for linking or redundancy. A 32 amp PowerCON
®
connector is used for mains supply.
This signal ow block diagram illustrates the exible mixing and routing, as well as the powerful signal processing capabilities, offered by the
PLM Series. The input routers allow for redundant and prioritized inputs, with automatic switch over in case of signal failure. The input mixers
provide mixing capabilities between the outputs of the two input routers. The two Lake Processing modules (covering all red blocks) provide user
EQ, crossover and output lters along with gain adjustments, mute, phase reverse, delay, and limiters. Module outputs can be routed to either
power output channel. Each power output channel provides individual channel attenuation, mute and phase reversal. Each power output channel
also implements congurable amplier gain and an advanced peak limiter in the ISVPL.
The exible architecture of the PLM Series allows the settings for each unit to be stored in different hierarchies. The Lake Processing modules
can be instantly congured with module les that are cross compatible with Dolby Lake products. Settings can also be stored and recalled on a
system and subsystem level (system/subsystem les) as well as on a device level (frame presets).