Data Sheet

ManualsBrandsLab Gruppen ManualsAudio EquipmentPower Amplifiers with DSP and Network

Item no. TDS-PLM10000Q_V18 - 30.11.2015

General

Number of input channels 2

Number of output channels 4

Peak total output all channels driven 10800 W

Max. Peak output voltage per channel 153 V

Max. output current per channel 49 A peak

Max. Output Power 2 ohms 4 ohms 8 ohms 16 ohms

All channels driven 2350 W

2300 W

1300 W 660 W

All channels driven into optimal impedance interval > 2700 W into 2.4 – 3.2 ohms

8 ohms bridged per ch. 4600 W

4 ohms bridged per ch. 4700 W

Bridged into optimal impedance interval

>5400 W into 4.8 – 6.2 ohms

Audio Performance

THD + N 20 Hz - 20 kHz for 1 W < 0.05%

THD + N at 1 kHz and 1 dB below clipping < 0.04%

Dynamic range with digital inputs (for all supported sample rates) > 116 dB

Dynamic range with analog inputs > 112 dB

Frequency response (1 W into 8 ohms, 20 Hz - 20 kHz) + /-0.05 dB

Common Mode Rejection (CMR) > 74 dB, 20 Hz to 20 kHz

Internal sample rate 96 k

Internal data path 32 bit oating point

Product propagation delay, best case (96 kHz AES) 1.61 ms

Product propagation delay, analog input 1.68 ms

Sample Rate Converters

THD + Noise 0.00003 %, 20 Hz - 20 kHz, unweighted

Analog to Digital inputs

Inputs 2 inputs x 2 link

Input sensitivity range +12 or +26 dBu

THD + Noise 0.00022 %, typical at 1 kHz unweighted at +26 dBu headroom setting

0.00033 %, typical at 20 Hz and 20 kHz unweighted at +26 dBu headroom setting

AES / EBU inputs

Inputs 2 inputs x 2 link

Supported resolutions ≤ 24 bit

Supported sample rates 44.1, 48, 88.2, 96, 176.4, 192 kHz

Dante Audio Network

Inputs and outputs 2 inputs, 2 outputs

Supported sample rates 48, 96 kHz

Supports redundant paths Yes

Flexible topology Yes

Network latency 0.8, 1.3 and 4 ms

Device presets

Local memory locations for the settings of the product 100

Limiters

Adjustable Inter-Sample Voltage Peak Limiter (ISVPL) 17.8 - 153 V, step size 0.1 V

Current Peak Limiter < 300 ms 49 A peak

Current Average Limiter (CAL) > 300 ms 25 Arms

LimiterMax (rms and peak limiters)

– MaxRMS (rms voltage limiter) Yes

– MaxPeak (peak voltage limiter) Yes

Gain

Amplier gain 22 - 44 dB, step size 0.1 dB

Analog attenuator -Inf to 0 dB, step size 0.25 dB

Rear-panel interface

AES / EBU / I/O (input + link) 2 x 3-pin XLR

Analog, 2-channel I/O (input + link) 4 x 3-pin XLR, electronically balanced

Output connectors Neutrik speakON (1 x NLT8, 2 x NLT4) or 4 Binding Posts (pairs)

Auto 10/100, Auto Uplink 2 x RJ45 etherCON

Control and monitoring interface Via Ethernet for Lake Controller software, or DLM (the 3rd Party Protocol)

Detachable mains cord Neutrik powerCON 32 A

Cooling Two fans front-to-rear airflow, temperature controlled speed

Front-panel user interface:

Display 2.5 inch, daylight readable LCD

Fault/Warning/Limit/Clip indicators RGB LEDs and detailed fault description on display

Mute and soft function buttons 8 provided

Standby Power button On/Standby

Mute Enable button Enables muting of outputs and inputs via soft-button keypad

Meter button Toggles through meter views

Menu button Provides a menu driven interface for full function front panel control

Rotary Encoder Yes

Exit button Provides a “back” function

Power

Operating voltage (45 - 66 Hz) Universal power supply 140 - 265 V / 70-135 V

Soft start / Inrush Current Draw Yes / max. 5 A

Power Average Limiter (PAL) Yes

Power Factor Correction (PFC) No

Breaker Emulation Limiter (BEL), software controlled 5 - 32 A No

Under-Voltage Limiter (UVL) No

Dimensions

Rack rail to rear panel W: 483 mm (19”), H:88 mm (2 U), D: 386 mm (15.2”)

Overall depth including handles and rear support 460 mm (18.1”)

Weight

13.5 kg (30 lbs)

Finish

Black painted steel chassis with black painted steel / aluminum front

Approvals

CE, ANSI/UL 60065 (ETL), CSA C22.2 NO. 60065, FCC

Note 1): Asymmetrical loading of the outputs will yield even higher ratings. If one (or two) channel(s) has reduced power requirements, then the voltage drop from the power supply will be reduced,

resulting in higher power availability for the other channel(s).

Note 2): Separate 230 V or 115 V versions available. Not selectable on the product.

All specifications are subject to change without notice.

Specifications PLM 10000Q