Lake Controller Operation Manual

ManualsBrandsLab Gruppen ManualsAudio EquipmentPower Amplifiers with DSP and Network

281

282

283

284

285

286

287

288

289

290

Table Of Contents

1. Welcome
- 1.1 Important Information
- 1.2 Introduction
- 1.3 Controller Overview
- 1.4 Manual Overview
2. Software Installation
- 2.1 Computer Requirements
- 2.2 Lake Controller Installation
- 2.3 Moving User Files between Installations
3. Network & Firewall Overview
- 3.1 Ethernet Overview
- 3.2 Firewall Configuration
- 3.3 IP Address Configuration
- 3.4 Wired Network Setup
- 3.5 Wireless Network Setup
- 3.6 Dante and AES67 Digital Audio Networking
4. Lake Controller Tutorial
- 4.1 Starting the Lake Controller
- 4.2 Overview of Main Page Components
- 4.3 Modules and Frames
- 4.4 Equalization
- 4.5 Crossovers
- 4.6 Groups
- 4.7 Lake Controller File Types
5. Home Menu Reference
- 5.1 Main Screen Home Menu
- 5.2 Accessing EQ/Levels from HOME
6. EQ/Levels Menu Reference
- 6.1 EQ/Levels Overview
- 6.2 Levels
- 6.3 Input EQ
- 6.4 Crossovers and HPF/LPF
- 6.5 Auxiliary Output Channels
7. System Store Recall Menu Reference
- 7.1 System Store Recall Navigation
- 7.2 Shortcut to Data/User Folder
- 7.3 Recall as New System—Open
- 7.4 Recall as Subsystem
- 7.5 Recall Compare
- 7.6 Recall as Virtual Sub System (SS)
- 7.7 Store System
- 7.8 Store Subsystem
- 7.9 File Utilities
- 7.10 System Presets
8. Modules Menu Reference
- 8.1 EQ/Levels
- 8.2 I/O Config
- 8.3 Label & Lock
- 8.4 Copy/Paste/Replace
- 8.5 Remove
- 8.6 Module Store/Recall
- 8.7 Add Page
- 8.8 Super Modules (LM & PLM Series only)
9. Module File Types & Lake LoadLibrary™
- 9.1 Module Types Overview
- 9.2 Supplementary Module Data
- 9.3 Module Type Abbreviations
- 9.4 Classic Crossovers/Auxiliary Outputs
- 9.5 Linear Phase Crossovers
- 9.6 FIR Module [Lake-enabled Amplifiers Only]
- 9.7 Mesa EQ Module
- 9.8 Lake LoadLibrary
- 9.9 Additional Information
10. Groups Menu Reference
- 10.1 Adding a Group
- 10.2 EQ/Levels
- 10.3 Assign
- 10.4 Label
- 10.5 Copy/Paste
- 10.6 Remove
- 10.7 Gang
- 10.8 Add Page
11. Solo/Mute Menu Reference
- 11.1 EQ/Levels
- 11.2 Solo/Mute Enable
- 11.3 Pile
- 11.4 All Mute
12. Icon Control Menu Reference
- 12.1 Meters On/Off
- 12.2 Icon Small/Normal/Medium/Large
13. User Preferences Menu Reference
- 13.1 Contexts
- 13.2 Delay Units
- 13.3 Designer Functions
- 13.4 Keyboard Shortcuts
- 13.5 About
- 13.6 Graphics
- 13.7 Show Mode
14. Pages Menu Reference
- 14.1 Cut Icon
- 14.2 Copy Icon
- 14.3 Paste Icon
- 14.4 Page Label
- 14.5 Page Delete
- 14.6 Page Add
- 14.7 Page Hide
- 14.8 Scrolling Pages
15. Network Menu Reference
- 15.1 Network
- 15.2 Multiple Controllers
- 15.3 Working Offline
16. Communication and Synchronization
- 16.1 Offline Modules
- 16.2 Communication/Network Errors
- 16.3 Synchronization
17. Faults and Warnings
- 17.1 Faults and Warnings Indication
18. Analyzer Plug-in
- 18.1 Overview
- 18.2 System Requirements
- 18.3 Analyzer Plug-in Quick Start Guide
- 18.4 Function Reference
19. Designer Mode Menu Reference
- 19.1 Designer Mode Basics
- 19.2 Designer Mode Security
- 19.3 Functional Reference Guide
- 19.4 Designer Worksheets
20. Lake-enabled Amplifier Reference
- 20.1 Signal Flow
- 20.2 Monitoring & Control
- 20.3 Lake LoadLibrary™
- 20.4 LoadSmart™
- 20.5 Navigation
- 20.6 Status Tab
- 20.7 History Tab
- 20.8 Events Tab
- 20.9 LoadSmart Tab
- 20.10 Output Tab
- 20.11 Power
21. LM Series Reference and Operation
- 21.1 Pass-Thru Input Router Functionality
- 21.2 GPIO Configuration
- 21.3 Remote Power Control & Event Logs
22. MY8-LAKE Reference and Operation
- 22.1 Signal Flow
- 22.2 Operation Mode
- 22.3 Host Analog Output Reference Configuration
- 22.4 I/O Configuration View Mode Options
23. Global Events and Control
- 23.1 Global Events Tab
- 23.2 Global Control Tab
- 23.3 Log Files
24. Keyboard Shortcuts
- 24.1 Enabling/Disabling Keyboard Shortcuts
- 24.2 General Keyboard Shortcuts
- 24.3 Button Bar Shortcuts
- 24.4 EQ, LEVELS, XOVER, and AUX Screen Shortcuts
25. External Control Interfaces
- 25.1 GPIO (LM Series Only)
- 25.2 AMX® and Crestron® Control
26. Command Line Options
- 26.1 Overview
- 26.2 Reference
27. Firmware Update
- 27.1 Backup System Configuration and Presets
- 27.2 Updating Firmware
- 27.3 Incompatible Firmware Notification in Lake Controller
- 27.4 Remote Power Cycle
28. Preset Manager
- 28.1 Starting the Lake Preset Manager
- 28.2 Screen Layout
- 28.3 Working with Frames
- 28.4 Working with Bank Files
- 28.5 Common Functionality
29. IP Address Reference
- 29.1 Network Essentials
- 29.2 Factory Reset Configuration
30. Corporate Information
- 30.1 Contact Details
- 30.2 Trademarks

284

Lake Controller Operation Manual Rev 1.6.1

Global Events and Control

2. Tap GLOBAL INFO.

3. Tap EVENTS & CONTROL [F8]

4. Tap the CONTROL tab

Figure 23-3: Global Control Tab

23. 2 .1 Global Power Control

Two buttons, ON and STANDBY, control the power status of all Lake-enabled devices (except MY8-LAKE)

that are online and present in the current system conguration. A conrmation is required prior to changing

this status across all devices.

Both buttons will be blue if a combination of status are present, or one button will be orange if all devices

have the same status.

Status indicators to the right of the buttons show the total number of LM and PLM Series devices in the

current system conguration that are ON, in STANDBY or OFFLINE.

If the Global Power Control default sequence time

is too quick, causing issues for the power distribu-

tion, this can be changed from the iC.ini ﬁle located

in the Conﬁg folder of Documents. The setting is

GLOBAL_POWER_DELAY and it is speciﬁed in ms.