Lake Controller Operation Manual

ManualsBrandsLab Gruppen ManualsAudio EquipmentPower Amplifiers with DSP and Network

100

Table Of Contents

1. Welcome
- 1.1 Important Information
- 1.2 Introduction
- 1.3 Controller Overview
- 1.4 Manual Overview
2. Software Installation
- 2.1 Computer Requirements
- 2.2 Lake Controller Installation
- 2.3 Moving User Files between Installations
3. Network & Firewall Overview
- 3.1 Ethernet Overview
- 3.2 Firewall Configuration
- 3.3 IP Address Configuration
- 3.4 Wired Network Setup
- 3.5 Wireless Network Setup
- 3.6 Dante Digital Audio Networking
4. Lake Controller Tutorial
- 4.1 Starting the Lake Controller
- 4.2 Overview of Main Page Components
- 4.4 Equalization
- 4.5 Crossovers
- 4.6 Groups
- 4.7 Lake Controller File Types
5. Home Menu Reference
- 5.1 Main Screen Home Menu
- 5.2 Accessing EQ/Levels from HOME
6. EQ/Levels Menu Reference
- 6.1 EQ/Levels Overview
- 6.2 Levels
- 6.3 Input EQ
- 6.4 Crossovers and HPF/LPF
- 6.5 Auxiliary Output Channels
7. System Store Recall Menu Reference
- 7.1 System Store Recall Navigation
- 7.2 Shortcut to Data/User Folder
- 7.3 Recall as New System—Open
- 7.4 Recall as Subsystem
- 7.5 Recall Compare
- 7.6 Recall as Virtual Sub System (SS)
- 7.7 Store System
- 7.8 Store Subsystem
- 7.9 File Utilities
- 7.10 System Presets
8. Modules Menu Reference
- 8.1 EQ/Levels
- 8.2 I/O Config
- 8.3 Label & Lock
- 8.4 Copy/Paste/Replace
- 8.5 Remove
- 8.6 Module Store/Recall
- 8.7 Add Page
- 8.8 Super Modules (LM & PLM Series only)
10. Groups Menu Reference
- 10.1 Adding a Group
- 10.2 EQ/Levels
- 10.3 Assign
- 10.4 Label
- 10.5 Copy/Paste
- 10.6 Remove
- 10.7 Gang
- 10.8 Add Page
11. Solo/Mute Menu Reference
- 11.1 EQ/Levels
- 11.2 Solo/Mute Enable
- 11.3 Pile
- 11.4 All Mute
12. Icon Control Menu Reference
- 12.1 Meters On/Off
- 12.2 Icon Small/Normal/Medium/Large
- 12.3 Global Status Indicator
13. User Preferences Menu Reference
- 13.1 Contexts
- 13.2 Delay Units
- 13.3 Designer Functions
- 13.4 Keyboard Shortcuts
- 13.5 About
- 13.6 Graphics
- 13.7 Show Mode
14. Pages Menu Reference
- 14.1 Cut Icon
- 14.2 Copy Icon
- 14.3 Paste Icon
- 14.4 Page Label
- 14.5 Page Delete
- 14.6 Page Add
- 14.7 Page Hide
- 14.8 Scrolling Pages
15. Network Menu Reference
- 15.1 Network
- 15.2 Multiple Controllers
- 15.3 Working Offline
16. Communication and Synchronization
- 16.1 Offline Modules
- 16.2 Communication/Network Errors
- 16.3 Synchronization
17. Faults and Warnings
- 17.1 Faults and Warnings Indication
18. Analyzer Plug-in
- 18.1 Overview
- 18.2 System Requirements
- 18.3 Analyzer Plug-in Quick Start Guide
- 18.4 Function Reference
19. Designer Mode Menu Reference
- 19.1 Designer Mode Basics
- 19.2 Designer Mode Security
- 19.3 Functional Reference Guide
- 19.4 Designer Worksheets
20. Lake-enabled Amplifier Reference
- 20.1 Signal Flow
- 20.2 Monitoring & Control
- 20.3 Lake LoadLibrary™
- 20.4 LoadSmart™
- 20.5 Navigation
- 20.6 Status Tab
- 20.7 History Tab
- 20.8 Events Tab
- 20.10 Output Tab
- 20.12 Global Events Tab
- 20.13 Global Control Tab
- 20.14 Log Files
21. LM Series Reference and Operation
- 21.1 Pass-Thru Input Router Functionality
- 21.2 GPIO Configuration
- 21.3 Remote Power Control & Event Logs
22. MY8-LAKE Reference and Operation
- 22.1 Signal Flow
- 22.2 Operation Mode
- 22.3 Host Analog Output Reference Configuration
- 22.4 I/O Configuration View Mode Options
23. Keyboard Shortcuts
- 23.1 Enabling/Disabling Keyboard Shortcuts
- 23.2 General Keyboard Shortcuts
- 23.3 Button Bar Shortcuts
- 23.4 EQ, LEVELS, XOVER, and AUX Screen Shortcuts
24. External Control Interfaces
- 24.1 GPIO (LM Series Only)
- 24.2 AMX® and Crestron® Control
25. Command Line Options
- 25.1 Overview
- 25.2 Reference
26. Firmware Update
- 26.1 Backup System Configuration and Presets
- 26.2 Updating Firmware
- 26.3 Incompatible Firmware Notification in Lake Controller
27. Preset Manager
- 27.1 Starting the Lake Preset Manager
- 27.2 Screen Layout
- 27.3 Working with Frames
- 27.4 Working with Bank Files
- 27.5 Common Functionality
28. IP Address Reference
- 28.1 Network Essentials
- 28.2 Factory Reset Configuration
29. Corporate Information
- 29.1 Contact Details
- 29.2 Trademarks

Lake Controller Operation Manual Rev 1.5.9

EQ/Levels Menu Reference

While most of the button bar functions are the same, some XOVER menu options and functions are differ-

ent for linear phase Modules. These differences are identied in the following sections.

6.4.5 Crossover Functions

CROSSOVER FUNCTIONS provides a submenu containing the following functions:

6.4.5.1 HPF/LPF Functions

▸ HPF/LPF FUNC EXIT exits this menu and returns to the CROSSOVER FUNCTIONS menu.

▸ INPUT HPF SETs the HPF to affect all output channels for the Module (depending on the frequency of

the HPF and outputs). Applicable to Contour Modules only.

▸ LOW OUTPUT HPF SETs the HPF to affect only the lowest output channel of the selected Module.

Applicable to Contour Modules only.

▸ HPF ENABLE enables/disables the HPF for the selected Module.

▸ LPF ENABLE enables/disables the LPF on the highest output channel for the selected Module.

INPUT HPF and LOW OUTPUT HPF are disabled for

the Linear Phase Brick Wall 4-Way Module. The

LP4way HPF is xed to INPUT HPF. Other Module

types, incl. LP2/LP3way provide the HPF option.

6.4.5.2 Crossover Hide

Available only in Designer Mode. When enabled (orange), the crossover page will be hidden when the

Module is locked, or after exiting from Designer Mode.

6.4.5.3 Crossover View Only

Available only in Designer Mode. When enabled (orange), the crossover page will be set as view only when

the Module is locked, or after exiting from Designer Mode.

6.4.5.4 EQ Preferences

This provides a submenu containing options regarding the view of the EQ scale.