Installation Guide

Corporate Office
Parex USA, Inc.
4125 E. La Palma Ave., Suite 250
Anaheim, CA 92807
[phone]
Tech Support: [phone]
Facilities
Riverside, CA
French Camp, CA
Albuquerque, NM
Colorado Springs, CO
Anaheim, CA
North Hollywood, CA
San Antonio, TX
Redan, GA
Wilkes Barre, PA
www.lahabrastucco.com
© 2011, Parex USA, Inc. LHPFSGAFDS 8/11
PACKAGING:
65 lbs. (29.5 kg) net weight in plastic pails.
n Storage: Protect from direct sunlight and
freezing at all times.
- Do not stack pails more than 3 pails high
n Shelf Life: One year if properly stored in
original unopened container.
COVERAGE:
Depending on the condition of the substrate and
method of application, approximate coverages are:
Smooth
Aggregate size: 0.5mm
280-300 sq. ft. (26-28 sq. m.) per pail
Swirl
Aggregate size: 1.5mm
120-135 sq. ft. (11-12.5 sq. m.) per pail
Fine
Aggregate size: 1.0mm
150-165 sq. ft. (14-15 sq. m.) per pail
Coarse
Aggregate size: 1.5mm
110-125 sq. ft. (10-11.5 sq. m.) per pail
DRYING TIME:
24 hours under normal conditions. High humidity
and low temperatures extend drying time.
CLEAN-UP:
Water soluble prior to drying. Clean tools and
equipment with water prior to drying.
SURFACE PREPARATION:
n Remove surface contaminants such as dust or
dirt without damaging the substrate.
n For previously painted surfaces, all loose and
chalking paint must be removed, and glossy
surfaces dulled.
n New concrete and masonry must be clean and
cured a minimum of 28 days.
n Check concrete surfaces for alkalinity and
treat. Any form-release agents or bond
breakers must be removed.
n Uneven concrete or masonry can be leveled
with Stucco Level Coat.
n For interior drywall, prepare as for painting.
n Prime with LaHabra Primer or Sanded Primer.
n For application of LaHabra Primer or Sanded
Primer, refer to the Product Data Sheet.
n For additional options, contact Parex USA
Technical Services Department.
MIXING:
n Use clean equipment for mixing and preparation.
n Stir to obtain a homogeneous consistency using
a heavy-duty 1/2-in. (13mm) drill with a rust free
paddle at 400-500 rpm. Avoid air entrainment.
n Add liquid color to the pail of finish. Make sure all
of the color is added by rinsing out the color vial
with water (1/3 of the vial’s volume) into the pail.
n Add the amount of water needed (up to a
maximum of 16 oz. per pail) to achieve finish
texture. To avoid color variations, add the same
amount of water to each pail of finish.
APPLICATION:
n Read the entire label before using this product.
n Always maintain a wet edge and work to corners
or joints. For best color consistency, use finish with
the same batch number within a wall section.
n Keep container closed when not in use.
n Use a clean stainless steel trowel and apply
a uniform coat the thickness of the largest
aggregate size of the finish.
n Texturing LaHabra Fine, Swirl and Coarse
Finishes: Use a clean plastic float or a stainless
steel trowel. A plastic float will roll the large
aggregates more than a stainless steel trowel.
Continuously dry clean the plastic float or steel
trowel while texturing. Use consistent pressure
and motion to achieve the desired texture.
n Texturing Smooth Finish:
- Optional: Level stucco brown coats with Stucco
Level Coat and let dry prior to finish application.
- Smooth Finish cannot generally be floated.
Texture will be “as trowelled.”
- Smooth Finish can be trowelled smooth to
simulate the texture of limestone.
- For smoothest application, apply in two tight
coats. Allow first coat to dry enough that it
will not be disturbed during application of the
second coat. When sec ond coat is partially dry,
trowel to desired smoothness. Light, consistent
misting with water during smoothing will
increase smoothness. Variations in color tint
and smoothness should be expected.
n Spray application: To achieve consistent texture,
spray application must use consis tent motion,
pressure, distance and spray angle. A job-site
mock-up for spray application is advised.
n Parex USA recommends the use of primers
to enhance the appearance and uniformity of
the finish, improve coverage and reduce the
chances of efflorescence.
LIMITATIONS:
n This is especially true when using dark colors or
finishes with a large aggregate.
n Ambient and surface temperature must be
40°F (4.4°C) or higher during application and
drying time. Supplemental heat and protection
from precipitation must be provided as needed.
n Use only on surfaces that are sound, clean, dry and
free from any residue that might affect the ability
of the finish to bond to the surface.
n Application in direct sunlight in hot weather may
adversely affect aesthetics .
n Not for use with EIFS.
WARNING:
n Read complete Warning information printed
on product container prior to use. For medical
emergency information, call 1-800-424-9300.
n For more information on handling this product
refer to its Material Safety Data Sheet (MSDS).
The most current MSDS and Product Data Sheet
(PDS) can be found on our website.
n
This Product Data Sheet has been prepared in
good faith on the basis of information available at
the time of publication. It is intended to provide
users with information about the guidelines for
the proper use and application of the covered
product(s) under normal environmental and
working conditions. Because each project is
different, Parex USA, Inc. cannot be responsible
for the consequences of variations in such
conditions, or for unforeseen conditions.