Installation Guide

Adacryl Optional Use:
As an Admix for Color Coat Patch
n Increases strength of stucco finishes
n Improves bond between stucco finish and base
coat surface
n Use 3 oz. (89 Milliliter/cc) to one 9 lb. bag of
Color Coat Patch in place of 3 oz. of water.
After the initial amount of water and the dry
components have been mixed, add the acrylic
admix. Mix no longer than required to provide
a uniform mixture. DO NOT OVER-MIX. Over-
mixing entrains excessive amounts of air which
weaken the material. Do not re-temper mixes
over 20 minutes old.
n Add an additional 4 to 8 oz. (236.6 to 355
Milliliter/cc) of water to achieve the desired
consistency for skip trowel texture applications,
add an additional 8 to 12 (118.3 to 236.6
Milliliter/cc) for Spray-Dash application, and
then let sit for approximately 5 to 10 minutes
in order to allow the material to slake. Doing
this allows the material to start its initial set.
Re mix for approximately 1 to 2 minutes,
adjusting the water and mixing only long
enough to achieve uniformity. The material
is now ready to be applied to the wall. (See
Application section.)
n Small amounts of cool clean potable water
may be added to adjust workability.
n Color Coat Patch should be used shortly after
mixing.
n Half batches may be mixed for convenience.
n Only Parex USA approved additives can be
added.
MATERIAL STANDARD:
Type-S Hydrated Lime: ASTM C206
Portland Cement: ASTM C150 Type
LaHabra Exterior Color Coat Patch:
Conforms to ASTM C926 recommendations.
LIMITATIONS:
n Use only on surfaces that are sound, clean, dry, unpainted,
and free from any residue that might affect the ability of
this product to bond to the surface.
n Exterior Stucco Color Coat is a finish material installed
at approximately 1/8” thick, it is not for use as a
stucco base material.
n Ambient and surface temperature must be 40°F (4°C)
or higher during application. Protect from freezing
for a period of not less than 24 hours after set has
occurred. Provide supplemental heat and protection
from precipitation as needed.
n Ambient and surface temperatures must not exceed
120° F (49° C) during and 24 hours after application.
n Application in direct sunlight in hot weather may
adversely affect aesthetics.
n Colors may vary due to substrate, weather, job
conditions and method of application. Before applying
product, a sample should be applied and allowed to
cure for color approval.
n Protect adjacent surfaces from overspray and
droppings, drips or spills. They should be removed
immediately with water or soap and water to prevent
the possibility of permanent staining.
n Always wear proper safety equipment, including
NIOSH particle mask, eye protection, and gloves when
mixing and applying this product.
WARNING:
n Read complete Warning information printed
on product container prior to use. For medical
emergency information, call 1-800-424-9300.
n For more information on handling this product refer
to its Safety Data Sheet (SDS). The most current SDS
and Product Data Sheet (PDS) can be found on our
website.
n This Product Data Sheet has been prepared in good
faith on the basis of information available at the time
of publication. It is intended to provide users with
information about the guidelines for the proper use
and application of the covered product(s) under normal
environmental and working conditions. Because
each project is different, Parex USA, Inc. cannot be
responsible for the consequences of variations in such
conditions, or for unforeseen conditions.
COVERAGE:
Coverage will vary depending on substrate,
thickness and texture of the application.
Approximate coverage per 9 lb. (4.1 kg) box:
n 9-14 ft
2
(0.8-1.3 m
2
)
CONTAINER:
Product is available in 9 lb. boxes.
STORAGE:
n Storage: Store off ground and protect from rain
and moisture.
n Shelf Life: 12 months if properly stored in the
original unopened container.
SURFACE PREPARATION:
n NOT recommended for application over painted,
sealed, wood or metal surfaces.
n Surfaces must be clean, free of dirt and foreign
material.
n Remove surface contaminants such as dust or
dirt without damaging the substrate.
n Color Coat Patch should be applied with an
ambient and surface temperature above 40°F
(4°C) for a minimum of 24 hours following the
application.
n The surface of the plaster base partially
determines the texture, color and final result of
the finish.
n Damage deeper than the finish or irregular and
uneven surface should be filled with a stucco
base coat or Stucco Level Coat material.
n Prior to application of exterior stucco finish, the
portland cement base coat shall be dampened
with clean water to control and equalize suction.
Allow surface moisture to dissipate prior to
application of the Exterior Stucco Color Coat.
n For additional options for surface preparation,
contact Parex USA Technical Support.
MIXING:
n Read the entire label before using this product.
n Use clean equipment for mixing and preparation.
n Add approximately 1-1/2 quarts (1.42L) of cool
clean potable water to a 2 gallon or larger pail.
n Add one 9 lb. bag of Color coat Patch and using
a heavy-duty ½ in. (13mm) drill with a rust-free
paddle at 400-500 rpm. mix for approximately 1
to 2 minutes until it is smooth and free of lumps.
© 2013, Parex USA, Inc. LH ECCP DS 0713
Corporate Office
Parex USA, Inc.
4125 E. La Palma Ave., Suite 250
Anaheim, CA 92807
[phone]
Tech Support: [phone]
Facilities
French Camp, CA
North Hollywood, CA
Riverside, CA
Colorado Springs, CO
Haines City, FL
www.lahabrastucco.com
Duluth, GA
Redan, GA
Albuquerque, NM
Allentown, PA
San Antonio, TX