Data Sheet

AC4490
Datasheet
https://www.lairdconnect.com/
28
© Copyright 2022 Laird Connectivity
All Rights Reserved
Americas: [phone]
Europe: [phone]
Hong Kong: [phone]
End Product Labeling
The final end product must be labeled in a visible area with the following: “Contains ISED: 2268C-44901000 / 2268C-4x90200”.
Plaque signalétique du produit final
Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: "Contient des ISED: 2268C-44901000 /
2268C-4x90200".
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF
module in the user’s manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à la façon d'installer ou de
supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et avertissements comme indiqué
dans ce manuel.
(For transmitters equipped with detachable antennas)
This radio transmitter [ISED: 2268C-44901000 / 2268C-4x90200] has been approved by Innovation, Science and Economic
Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna
types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited
for use with this device.
Le présent émetteur radio ISED: 2268C-44901000 / 2268C-4x90200] a été approuvé par Innovation, Sciences et
Développement économique Canada pour fonctionner avec les types d'antenne énumérés ci dessous et ayant un gain
admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué
pour tout type figurant sur la liste, sont strictement interdits pour l'exploitation de l'émetteur.
For certified antenna list, see Table 8 for all revision 1.0 hardware and Table 9 for revision 2.0 hardware (AC4490-1000M /
AC4490LR-1000M).
12.6 Antenna Requirements
WARNING for Hardware Revision 1.0: This device has been tested with an MMCX connector with the above listed antennas.
When integrated into the OEM’s product, these fixed antennas require professional installation preventing end-users from
replacing them with non-approved antennas. Antenna Y2283 and SG101N915 strictly require professional installation. Any
antenna not in the previous table must be tested to comply with FCC Section 15.203 for unique antenna connectors and
Section 15.247 for emissions. Contact Laird Connectivity for assistance.
Caution: Any change or modification not expressly approved by Laird Connectivity could void the user's authority to operate
the equipment.
For certified antenna list, see Table 8 for all revision 1.0 hardware.
WARNING for Hardware Revision 2.0: This device has been tested with an MMCX connector with the above listed antennas.
When integrated into the OEM’s product, these fixed antennas require professional installation preventing end-users from
replacing them with non-approved antennas. Any antenna not in the previous table must be tested to comply with FCC Section
15.203 and Section 15.247 for emissions. Contact Laird Connectivity for assistance.
Caution: Any change or modification not expressly approved by Laird Connectivity could void the user's authority to operate
the equipment.
For certified antenna list, see Table 9 for revision 2.0 hardware (AC4490-1000M / AC4490LR-1000M).