User Manual

ManualsBrandsLaird Technologies ManualsElectronicsProFLEX01-SOC

Table Of Contents

ProFLEX01-SOC TRANSCEIVER MODULE

DATASHEET

The information in this document is subject to change without notice.

Confirm the data is current by downloading the latest revision from www.lsr.com.

Integrated Transceiver Modules for ZigBee / 802.15.4 (2.4 GHz)

Development Kit Available

FEATURES

• 100mW output power

• Long range: 4000 feet

• Miniature footprint: 0.9” x 1.63”

• Integrated PCB F antenna or u.fl connector

for external antenna

• Worldwide acceptance: FCC, IC and ETSI

• Integrated 8051 microcontroller with 256k

FLASH and 8k RAM

• 4MBit Serial FLASH

• Supports ZigBee, 802.15.4 MAC, RF4CE,

SimpliciTI, and custom

• LSR serial protocol based on 802.15.4 MAC

• Low power operation

• RoHS compliant

• Streamlined development with LSR design

services.

• License options available to purchase

design or integrate design.

APPLICATIONS

• Security

• Lighting Control

• HVAC Control

• Sensor Networks

• Medical

• Smart Energy

DESCRIPTION

The ProFLEX01-SOC module is a high

performance 2.4 GHz IEEE 802.15.4 System-

On-Chip (CC2530)

radio/microcontroller and

power amplifier (CC2591) in

a cost effective, pre-certified

footprint.

The module comes preloaded with the TI MAC-

Stack that can be used with the LSR host serial

protocol.

Full debug and programming capabilities are

included to develop custom applications. Easily

load the TI ZigBee stack, 802.15.4 MAC,

RF4CE, or SimplicitTI onto the module and

create your own network.

Need to get to market quickly? Not an expert in

802.15.4 or ZigBee? Need a custom antenna?

Would you like to own the design? Would you

like a custom design? Not quite sure what you

need? Do you need help with your host board?

LS Research Design Services will be happy to

develop custom hardware or software, integrate

the design, or license the design so you can

manufacture yourself. Contact us at

sales@lsr.com or call us at 262-375-4400.

ORDERING INFORMATION

Order Number

Description

450-0035

ProFLEX01-SOC Module with PCB F antenna

450-0044

ProFLEX01-SOC Module with u.fl connector for external antenna

450-0051

ProFLEX01-SOC Development Kit

Table 1 Orderable ProFLEX01-SOC Model Numbers

Summary of content (34 pages)

PAGE 1
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET Integrated Transceiver Modules for ZigBee / 802.15.4 (2.4 GHz) Development Kit Available FEATURES DESCRIPTION • 100mW output power • Long range: 4000 feet • Miniature footprint: 0.9” x 1.63” • Integrated PCB F antenna or u.fl connector for external antenna • Worldwide acceptance: FCC, IC and ETSI • Integrated 8051 microcontroller with 256k FLASH and 8k RAM • 4MBit Serial FLASH • Supports ZigBee, 802.15.
PAGE 2
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET MODULE ACCESSORIES Order Number Description 001-0001 2.4 GHz Dipole Antenna with Reverse Polarity SMA Connector 080-0001 u.fl to Reverse Polarity SMA Bulkhead Cable 105mm The information in this document is subject to change without notice. Confirm the data is current by downloading the latest revision from www.lsr.com. 330-0049-R0.
PAGE 3
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET Analog TMR/PWM BLOCK DIAGRAM CC2591 (PA/LNA) Antenna CC2530 SOC Serial I/O 8051 Microcontroller And Radio GPIO PGM/DBG Serial FLASH (4MBit) Figure 1 ProFLEX01-SOC Module Block Diagram – High-Level DEVELOPMENT KIT The ProFLEX01-SOC Development Kit can be used out of the box to evaluate RF range performance with the simple press of a button.
PAGE 4
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET TABLE OF CONTENTS FEATURES .......................................................................................................................... 1 APPLICATIONS ................................................................................................................... 1 DESCRIPTION ..................................................................................................................... 1 ORDERING INFORMATION ................................
PAGE 5
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET OPTICAL INSPECTION ..................................................................................................... 24 REWORK ........................................................................................................................... 24 SHIPPING, HANDLING, AND STORAGE ......................................................................... 24 Shipping ............................................................................................
PAGE 6
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET MODULE PINOUT AND PIN DESCRIPTIONS MCU# 35 34 20 19 12 - GND GND GND NC NC NC NC NC NC Debug Data Debug Clock NC NC nRESET NC NC NC NC NC P0.0 NC P0.7 NC NC NC VCC - 3V3DC 1 69 2 68 3 67 4 66 5 65 6 64 7 63 8 62 9 61 10 60 11 59 12 58 Texas Instruments CC2530 13 14 57 56 15 55 16 54 17 53 18 52 19 51 20 50 21 49 22 48 23 47 24 46 25 45 26 44 GND GND GND NC NC NC NC NC P0.3 P0.2 P0.5 P0.
PAGE 7
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET Module Pin Name MCU Pin Type 1 GND N/A GND Ground 2 GND N/A GND Ground 3 GND N/A GND Ground 4 NC N/A NC No Connect 5 NC N/A NC No Connect 6 NC N/A NC No Connect 7 NC N/A NC No Connect 8 NC N/A NC No Connect 9 NC N/A NC No Connect 10 Debug Data 35 I/O Debug Data signal for programming/debugging. 11 Debug Clock 34 Input Debug Clock signal for programming/debugging.
PAGE 8
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET Module Pin Name MCU Pin Type 30 P0.6 13 I/O General-purpose digital I/O or analog input. For peripheral functionality see CC2530 User’s Guide. 31 P0.7 12 I/O General-purpose digital I/O or analog input. For peripheral functionality see CC2530 User’s Guide. 32 NC N/A NC No Connect 33 NC N/A NC No Connect 34 NC N/A NC No Connect 35 P1.6/UART TX 38 I/O General-purpose digital I/O UART transmit data output.
PAGE 9
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET Module Pin Name MCU Pin Type 58 P0.4 37 I/O General-purpose digital I/O or analog input. For peripheral functionality see CC2530 User’s Guide. 59 P0.5 14 I/O General-purpose digital I/O or analog input. For peripheral functionality see CC2530 User’s Guide. 60 P0.2 17 I/O General-purpose digital I/O or analog input. For peripheral functionality see CC2530 User’s Guide. 61 P0.3 16 I/O General-purpose digital I/O or analog input.
PAGE 10
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET MODULE OVERVIEW Figure 4 below shows the internal interconnects of the ICs on the ProFLEX01-SOC module. Consult the respective IC datasheets for details, or contact LSR sales to purchase the ProFLEX01-SOC module schematics as part of LSR’s ModFLEX™ design program. For a high-level block diagram of the ProFLEX01-SOC module, see Figure 1. Vcc 7 HGM P1.1 9 5 PA_EN P1.3 7 6 EN RF_N 26 2 RF_N RF_P 25 4 RF_P P0.6 13 2 SO P0.1 18 5 SI P1.
PAGE 11
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET Figure 5 CC2530 SOC Block Diagram The information in this document is subject to change without notice. Confirm the data is current by downloading the latest revision from www.lsr.com. 330-0049-R0.
PAGE 12
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET PA/LNA The CC2591 is a cost-effective and high performance RF Front End for low-power and low-voltage 2.4 GHz wireless applications. It is a range extender for all existing and future 2.4 GHz low-power RF transceivers, transmitters and System-on-Chip products from Texas Instruments. It increases the link budget by providing a power amplifier for increased output power, and a LNA with low noise figure for improved receiver sensitivity.
PAGE 13
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET It is also best to keep some clearance between the antenna and nearby objects. This includes how the module is mounted in the product enclosure. Unless the items on the following list of recommendations are met, the radiation pattern can be heavily distorted. Whichever antennas are used, it is best to keep a few things in mind when determining their location. • Never place ground plane or copper trace routing underneath the antenna.
PAGE 14
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET MODES OF OPERATION • With a host microcontroller • With the TI 802.15.4 MAC, ZigBee stack, RF4CE stack, and SimpliciTI Host Microcontroller PC LSR Test Tool Software UART ProFLEX Module on Evaluation Board -OR- Your Microcontroller (Host) of Choice UART ProFLEX Module on Your Board Figure 7 Host Microcontroller Modes of Operation Out of the box the ProFLEX01-SOC module contains an 802.15.4 based application that uses a host serial processor.
PAGE 15
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET Software Stacks There are four software stacks provided by TI to streamline development: MAC (802.15.4) SimpliciTI RF4CE Z-Stack (ZigBee) Overall Complexity and Development Effort Figure 9 ProFLEX01-SOC Compatible Stacks TI MAC (802.15.4) • • • Use for applications requiring point-to-point or star network topology.
PAGE 16
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET SimpliciTI • • • Used for simple and small RF networks. Advantages: Easy to use and supports range extenders and access points. Disadvantages: Intended for small networks with low RF data bandwidth. Application Software (to control switches, LED’s, serial ports, etc) Software Interface SimpliciTI Stack (To Tx/Rx RF data) Figure 11 ProFLEX01-SOC with SimpliciTI RF4CE • Use when designing a RF4CE compatible remote control.
PAGE 17
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET DEVELOPMENT TOOLS TI CC-DEBUGGER Custom firmware development can be done on the ProFLEX01-SOC module using development tools available thought TI. Shown in Figure 14 is a USB CC-DEBUGGER, which can be used both for debugging or programming. It plugs directly into the ProFLEX01-SOC Development Board (see Figure 2), and can easily be adapted to other hardware. See the Texas Instruments website for more information.
PAGE 18
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET ELECTRICAL SPECIFICATIONS The majority of these characteristics are based on the use of the TI 802.15.4 MAC loaded with the generic application firmware written by LSR. Custom firmware may require these values to be recharacterized by the customer. Absolute Maximum Ratings Parameter Min Max Unit Power supply voltage (VCC) -0.2 +3.6 V Voltage on any GPIO -0.2 VCC + 0.
PAGE 19
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET General Characteristics Parameter Min RF frequency range 2405 RF data rate Typ Max Unit 2480 MHz 250 Host data rate 1.2 Flash memory kbps 19.2 921.6 kbps 256 kBytes 8 kBytes RAM Table 5 General Characteristics Power Consumption Parameter Test Conditions Min Typ Max Unit Transmit mode 2440 MHz, 3.3V, +25°C, +20 dBm output, 50 Ω 130 160 195 mA Receive mode 2440 MHz, 3.
PAGE 20
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET RF Characteristics Nominal Transmitter Characteristics (TA = 25°C, VCC = 3.3V, fC = 2440 MHz, 50Ω) Parameter Test Conditions Min Typ Max Unit Minimum output power Min 802.15.4 MAC API Setting 7 9 11 dBm Maximum output power Max 802.15.4 MAC API Setting 18 20 22 dBm 20 dBm Programmable output power range 9.5 Transmit current – min output Min 802.15.4 MAC API Setting 75 78 85 mA Transmit current – max output Max 802.15.
PAGE 21
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET Maximum Transmitter Characteristics (TA = -40°C, VCC = 3.6V, fC = 2440 MHz, 50Ω) Parameter Test Conditions Min Typ Max Unit Minimum output power Min 802.15.4 MAC API Setting 13 14 15 dBm Maximum output power Max 802.15.4 MAC API Setting 21 23 24 dBm 23 dBm Programmable output power range 14 Transmit current – min output Min 802.15.4 MAC API Setting 80 87 95 mA Transmit current – max output Max 802.15.
PAGE 22
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET Receiver Characteristics (TA = 25°C, VCC = 3.3V, fC = 2440 MHz) Parameter Test Conditions Receiver sensitivity (1% PER) HGM Saturation (maximum input level) (1% PER) HGM Interference rejection Desired signal at -82 dBm, 802.15.
PAGE 23
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET SOLDERING RECOMMENDATIONS Recommended Reflow Profile for Lead Free Solder Note: The quality of solder joints on the castellations (‘half vias’) where they contact the host board should meet the appropriate IPC Specification. See IPC-A-610-D Acceptability of Electronic Assemblies, section 8.2.4 Castellated Terminations.” The information in this document is subject to change without notice. Confirm the data is current by downloading the latest revision from www.
PAGE 24
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET CLEANING SHIPPING, HANDLING, AND STORAGE In general, cleaning the populated modules is strongly discouraged. Residuals under the module cannot be easily removed with any cleaning process. Shipping • • • Cleaning with water can lead to capillary effects where water is absorbed into the gap between the host board and the module. The combination of soldering flux residuals and encapsulated water could lead to short circuits between neighboring pads.
PAGE 25
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET AGENCY STATEMENTS Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 26
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET Industry Canada Statements Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.
PAGE 27
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET OEM Responsibilities to comply with FCC and Industry Canada Regulations The ProFLEX01-SOC Module has been certified for integration into products only by OEM integrators under the following conditions: This device is granted for use in Mobile only configurations in which the antennas used for this transmitter must be installed to provide a separation distance of at least 20cm from all person and not be co-located with any other transmitters except in accordance wi
PAGE 28
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET End Product Labelling The ProFLEX01-SOC Module is labeled with its own FCC ID and IC Certification Number. If the FCC ID and IC Certification Number are not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module.
PAGE 29
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET Le ProFLEX01-SOC Module est étiqueté avec sa propre ID de la FCC et IC numéro de certification. Si l'ID de la FCC et IC numéro de certification ne sont pas visibles lorsque le module est installé à l'intérieur d'un autre appareil, puis l'extérieur de l'appareil dans lequel le module est installé doit également afficher une étiquette mentionnant le module ci-joint.
PAGE 30
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET MECHANICAL DATA PCB Footprint Figure 15 PCB footprint The information in this document is subject to change without notice. Confirm the data is current by downloading the latest revision from www.lsr.com. 330-0049-R0.
PAGE 31
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET General Module Dimensions Figure 16 Basic dimensions The information in this document is subject to change without notice. Confirm the data is current by downloading the latest revision from www.lsr.com. 330-0049-R0.
PAGE 32
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET COMPATIBILITY To maintain compatibility with other ModFLEX™ family transceiver modules it is important to use the module pins in your application as they are designated in Figure 17. Since the available GPIO and peripherals vary per micro, not all pins may be populated. All attempts are made to lay out modules starting with the lowest number in the peripheral (ADC, TMR/PWM, GPIO) series.
PAGE 33
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET MODULE REVISION HISTORY Rev A • Initial production release. The information in this document is subject to change without notice. Confirm the data is current by downloading the latest revision from www.lsr.com. 330-0049-R0.
PAGE 34
ProFLEX01-SOC TRANSCEIVER MODULE DATASHEET CONTACTING LS RESEARCH Headquarters LS Research, LLC W66 N220 Commerce Court Cedarburg, WI 53012-2636 USA Tel: 1(262) 375-4400 Fax: 1(262) 375-4248 Website www.lsr.com Technical Support forum.lsr.com Sales Contact sales@lsr.com The information in this document is provided in connection with LS Research (hereafter referred to as “LSR”) products.