Datasheet

ManualsBrandsLaird ManualsFiltersEcE Extrusion Strip 6.4x6.4mm

www.lairdtech.com

EMI ESSENTIALSEMI ESSENTIALS

thgieH eerFseigolonhceT driaL

Part No. O.D. I.D. Maximum “T”

8903-0175-XX 1.625 (41,3) 1.125 (28,6) 0.032 (0,8)

8904-0175-XX 1.625 (41,3) 1.125 (28,6) 0.062 (1,6)

8905-0175-XX 1.625 (41,3) 1.125 (28,6) 0.093 (2,4)

8906-0175-XX 1.625 (41,3) 1.125 (28,6) 0.125 (3,2)

8907-0175-XX 1.625 (41,3) 1.125 (28,6) 0.156 (4,0)

8918-0175-XX 1.625 (41,3) 1.125 (28,6) 0.187 (4,7)

8909-0175-XX 1.625 (41,3) 1.125 (28,6) 0.250 (6,4)

8902-0176-XX 1.884 (47,9) 1.760 (44,7) 0.032 (0,8)

8901-0176-XX 1.884 (47,9) 1.760 (44,7) 0.062 (1,6)

8903-0176-XX 1.884 (47,9) 1.760 (44,7) 0.093 (2,4)

8904-0176-XX 1.884 (47,9) 1.760 (44,7) 0.125 (3,2)

8905-0176-XX 1.884 (47,9) 1.760 (44,7) 0.156 (4,0)

8916-0176-XX 1.884 (47,9) 1.760 (44,7) 0.187 (4,7)

8907-0176-XX 1.884 (47,9) 1.760 (44,7) 0.250 (6,4)

How to Specify

1. From Table 1 on pages 25 to 27, determine the O.D., the I.D., and the

thickness “T” of the ElectroGround washer that suits the specific

application. Note: Please consult Laird Technologies sales department for

sizes not shown in Table 1.

2. From Table 2, insert material code in place of XX in base part number.

3. For tolerances O.D. and I.D. refer to Table 3.

Example:

1. Dimensions required: O.D. = 0.200 I.D. = 0.125, and Thickness = 0.032

(from Table 1).

2. Base Part Number: 8904-0178-XX (from Table 1).

3. Material required is Beryllium Copper Code 40 (from Table 2).

4. Full part number is 8904-0178-40.

noitacificepS eriWepyTedoC lairetaM

035-CQQ yollA 52reppoC muillyreB04

lenoM24

QQN-281 Class A

yollA 6505munimulA34

025B MTSAleetS detalP niT44

403leetS sselniatS64

.D.I.D.OseziS T

0.030 (0,8) to 0.062 (1,6)

0.010 (

0,3)

0.010 (

0,3)

0.062 (1,6) to 1.0 (25,4)

0.015 (

0,4)

0.015 (

0,4)

1.0 (25,4) to 2.0 (50,8)

0.020 (

0,5)

0.020 (

0,5)

Other alloys available upon request.

All dimensions shown are in inches (millimeters) unless otherwise specified.

TABLE 1. DIMENSIONS (continued)

TABLE 2. MATERIALS

TABLE 3. TOLERANCES

htdiW.oN traP seigolonhceT driaL

)0,1 ± 4,6( 040.0 ± 052.044-5200-0038

)0,1 ± 7,9( 040.0 ± 083.044-8300-0038

)5,1 ± 7,21( 060.0 ± 005.044-0500-0038

)5,1 ± 1,91( 060.0 ± 057.044-5700-0038

)5,1 ± 4,52( 060.0 ± 000.144-0010-0038

)1,3 ± 1,83( 021.0 ± 005.144-0510-0038

)1,3 ± 5,44( 021.0 ± 057.144-5710-0038

)8,4 ± 2,75( 091.0 ± 052.244-5220-0038

All dimensions shown are in inches (millimeters) unless otherwise specified.

Laird ElectroMesh tape has a double layered strip of knitted

provide effective EMI shielding and grounding for electrical and

electronic cable assemblies.

It is particularly useful in applications where the need for EMI protection is

determined after cable assembly is complete and standard braided cable

jackets cannot be used. The flexible structure of the ElectroMesh Tape permits

it to conform to irregular surfaces and contours during the wrapping process.

• Tin plating for excellent solderability

• Useful in both shielding and grounding applications forstatic discharge

• Tin plated copper clad steel wire provides greater strength and

performance than other tape materials

• Knit loop structure provides uniform coverage without any wrinkles or

creases

• Available in other alloys and wire dimensions

• Supplied in 50 ft. (15,2 m) rolls. (Note: When determining quantity needed,

50% overlap is recommended.)

• Mesh tape also available in Monel

(material code 42); BeCu (material

code 40); Aluminum (material code 43); and Stainless Steel (material code

46)

• Other alloys available upon request

ElectroMesh tape is 0.020 (0,5) thick. It is available in tin plated copper clad

steel ASTM-B-250, with a diameter of 0.005 (0,1) and with 10–12 openings

per inch.

TABLE 1. ELECTROMESH TAPE PART NUMBERS

wire mesh to

KNITTED CONDUCTIVE GASKETS

ELECTROMESH

TAPE

KNITTED CONDUCTIVE GASKETS

ELECTROGROUND

EMI WASHERS

thgieH eerFseigolonhceT driaL

Part No. O.D. I.D. Maximum “T”

8903-0175-XX 1.625 (41,3) 1.125 (28,6) 0.032 (0,8)

8904-0175-XX 1.625 (41,3) 1.125 (28,6) 0.062 (1,6)

8905-0175-XX 1.625 (41,3) 1.125 (28,6) 0.093 (2,4)

8906-0175-XX 1.625 (41,3) 1.125 (28,6) 0.125 (3,2)

8907-0175-XX 1.625 (41,3) 1.125 (28,6) 0.156 (4,0)

8918-0175-XX 1.625 (41,3) 1.125 (28,6) 0.187 (4,7)

8909-0175-XX 1.625 (41,3) 1.125 (28,6) 0.250 (6,4)

8902-0176-XX 1.884 (47,9) 1.760 (44,7) 0.032 (0,8)

8901-0176-XX 1.884 (47,9) 1.760 (44,7) 0.062 (1,6)

8903-0176-XX 1.884 (47,9) 1.760 (44,7) 0.093 (2,4)

8904-0176-XX 1.884 (47,9) 1.760 (44,7) 0.125 (3,2)

8905-0176-XX 1.884 (47,9) 1.760 (44,7) 0.156 (4,0)

8916-0176-XX 1.884 (47,9) 1.760 (44,7) 0.187 (4,7)

8907-0176-XX 1.884 (47,9) 1.760 (44,7) 0.250 (6,4)

How to Specify

1. From Table 1 on pages 25 to 27, determine the O.D., the I.D., and the

thickness “T” of the ElectroGround washer that suits the specific

application. Note: Please consult Laird Technologies sales department for

sizes not shown in Table 1.

2. From Table 2, insert material code in place of XX in base part number.

3. For tolerances O.D. and I.D. refer to Table 3.

Example:

1. Dimensions required: O.D. = 0.200 I.D. = 0.125, and Thickness = 0.032

(from Table 1).

2. Base Part Number: 8904-0178-XX (from Table 1).

3. Material required is Beryllium Copper Code 40 (from Table 2).

4. Full part number is 8904-0178-40.

noitacificepS eriWepyTedoC lairetaM

035-CQQ yollA 52reppoC muillyreB04

lenoM24

QQN-281 Class A

yollA 6505munimulA34

025B MTSAleetS detalP niT44

403leetS sseln

iatS64

.D.I.D.OseziS T

0.030 (0,8) to 0.062 (1,6)

0.010 (

0,3)

0.010 (

0,3)

0.062 (1,6) to 1.0 (25,4)

0.015 (

0,4)

0.015 (

0,4)

1.0 (25,4) to 2.0 (50,8)

0.020 (

0,5)

0.020 (

0,5)

Other alloys available upon request.

All dimensions shown are in inches (millimeters) unless otherwise specified.

TABLE 1. DIMENSIONS (continued)

TABLE 2. MATERIALS

TABLE 3. TOLERANCES

thgieH eerFseigolonhceT driaL

Part No. O.D. I.D. Maximum “T”

8903-0175-XX 1.625 (41,3) 1.125 (28,6) 0.032 (0,8)

8904-0175-XX 1.625 (41,3) 1.125 (28,6) 0.062 (1,6)

8905-0175-XX 1.625 (41,3) 1.125 (28,6) 0.093 (2,4)

8906-0175-XX 1.625 (41,3) 1.125 (28,6) 0.125 (3,2)

8907-0175-XX 1.625 (41,3) 1.125 (28,6) 0.156 (4,0)

8918-0175-XX 1.625 (41,3) 1.125 (28,6) 0.187 (4,7)

8909-0175-XX 1.625 (41,3) 1.125 (28,6) 0.250 (6,4)

8902-0176-XX 1.884 (47,9) 1.760 (44,7) 0.032 (0,8)

8901-0176-XX 1.884 (47,9) 1.760 (44,7) 0.062 (1,6)

8903-0176-XX 1.884 (47,9) 1.760 (44,7) 0.093 (2,4)

8904-0176-XX 1.884 (47,9) 1.760 (44,7) 0.125 (3,2)

8905-0176-XX 1.884 (47,9) 1.760 (44,7) 0.156 (4,0)

8916-0176-XX 1.884 (47,9) 1.760 (44,7) 0.187 (4,7)

8907-0176-XX 1.884 (47,9) 1.760 (44,7) 0.250 (6,4)

How to Specify

1. From Table 1 on pages 25 to 27, determine the O.D., the I.D., and the

thickness “T” of the ElectroGround washer that suits the specific

application. Note: Please consult Laird Technologies sales department for

sizes not shown in Table 1.

2. From Table 2, insert material code in place of XX in base part number.

3. For tolerances O.D. and I.D. refer to Table 3.

Example:

1. Dimensions required: O.D. = 0.200 I.D. = 0.125, and Thickness = 0.032

(from Table 1).

2. Base Part Number: 8904-0178-XX (from Table 1).

3. Material required is Beryllium Copper Code 40 (from Table 2).

4. Full part number is 8904-0178-40.

noitacificepS eriWepyTedoC lairetaM

035-CQQ yollA 52reppoC muillyreB04

lenoM24

QQN-281 Class A

yollA 6505munimulA34

025B MTSAleetS detalP niT44

403leetS sselniatS64

.D.I.D.OseziS T

0.030 (0,8) to 0.062 (1,6)

0.010 (

0,3)

0.010 (

0,3)

0.062 (1,6) to 1.0 (25,4)

0.015 (

0,4)

0.015 (

0,4)

1.0 (25,4) to 2.0 (50,8)

0.020 (

0,5)

0.020 (

0,5)

Other alloys available upon request.

All dimensions shown are in inches (millimeters) unless otherwise specified.

TABLE 1. DIMENSIONS (continued)

TABLE 2. MATERIALS

TABLE 3. TOLERANCES