Datasheet

86
www.lairdtech.com
87
www.lairdtech.com
EMI ESSENTIALSEMI ESSENTIALS
EXTRUSIONS GUIDE
MIL-DTL-85328
PART NUMBER
PART
NUMBER
NOMINAL DIMENSIONS
A B
M83528/009X001 8861-0100 0.063 (1,6) 0.042 (1,1)
8861-0179 0.079 (2,0) 0.039 (1,0)
8861-0181 0.079 (2,0) 0.059 (1,5)
M83528/009X002 8861-0105 0.095 (2,4) 0.062 (1,6)
M83528/009X003 8861-0110 0.120 (3,0) 0.075 (1,9)
M83528/009X004 8861-0115 0.125 (3,2) 0.062 (1,6)
M83528/009X005 8861-0120 0.156 (4,0) 0.062 (1,6)
8861-0121 0.187 (4,8) 0.125 (3,2)
8861-0167 0.188 (4,8) 0.062 (1,6)
8861-0193 0.189 (4,8) 0.189 (4,8)
M83528/002X006 8861-0125 0.250 (6,4) 0.062 (1,6)
8861-0173 0.250 (6,4) 0.125 (3,2)
8861-0174 0.250 (6,4) 0.188 (4,8)
8861-0136 0.250 (6,4) 0.200 (5,1)
8861-0175 0.252 (6,4) 0.031 (0,8)
8861-0183 0.378 (9,6) 0.063 (1,6)
8861-0172 0.500 (12,7) 0.020 (0,5)
8861-0131 0.500 (12,7) 0.042 (1,1)
8861-0182 0.500 (12,7) 0.059 (1,5)
M83528/009X007 8861-0130 0.500 (12,7) 0.075 (1,9)
8861-0188 0.500 (12,7) 0.094 (2,4)
M83528/009X008 8861-0135 0.500 (12,7) 0.125 (3,2)
M83528/009X009 8861-0140 0.500 (12,7) 0.188 (4,8)
8861-0142 0.750 (19,1) 0.040 (1,0)
8861-0141 0.750 (19,1) 0.042 (1,1)
M83528/009X010 8861-0145 0.750 (19,1) 0.062 (1,6)
8861-0184 0.827 (21,0) 0.071 (1,8)
8861-0189 0.827 (21,0) 0.094 (2,4)
M83528/009X011 8861-0150 0.880 (22,4) 0.062 (1,6)
8861-0103 0.984 (25,0) 0.043 (1,1)
8861-0169 1.00 (25,4) 0.062 (1,6)
8861-0192 1.00 (25,4) 0.126 (3,2)
M83528/009X012 8861-0155 1.00 (25,4) 0.250 (6,4)
M83528/009X013 8861-0160 1.18 (30,0) 0.062 (1,6)
TOLERANCES ALL PROFILES
DIMENSIONS TOLERANCE
Under 0.101 (2,6) ± 0.005 (0,15)
0.101 to 0.200 (2,6 to 5,1) ± 0.008 (0,2)
0.201 to 0.300 (5,1 to 7,6) ± 0.010 (0,3)
0.301 to 0.500 (7,6 to 12,7) ± 0.015 (0,4)
Over 0.500 (12,7) ± 0.020 (0,5)
PART NUMBER
NOMINAL DIMENSIONS
A B C
8862-0112 0.125 (3,2) 0.125 (3,2) 0.078 (2,0)
8862-0113 0.200 (5,1) 0.130 (3,3) 0.090 (2,3)
8862-0114 0.250 (6,4) 0.250 (6,4) 0.156 (4,0)
8862-0100 0.330 (8,4) 0.305 (7,7) 0.125 (3,2)
8862-0105 0.375 (9,5) 0.375 (9,5) 0.188 (4,8)
Rectangular Strips Hollow Rectangular Strips
ELECTROSEAL CONDUCTIVE
ELASTOMER MATERIAL
THICKNESS/TOLERANCE 10 X 10 SHEET 10 X 15 SHEET 15 X 20 SHEET 18 X 18 SHEET
0.020 ± 0.004 (0,5 ± 0,1) 8860-0020-100-XX 8860-0020-150-XX 8860-0020-300-XX N/A
0.032 ± 0.005 (0,8 ± 0,1) 8860-0032-100-XX 8860-0032-150-XX 8860-0032-300-XX 8860-0032-324-XX
0.045 ± 0.005 (1,1 ± 0,1) 8860-0045-100-XX 8860-0045-150-XX 8860-0045-300-XX 8860-0045-324-XX
0.062 ± 0.007 (1,5 ± 0,2) 8860-0062-100-XX 8860-0062-150-XX 8860-0062-300-XX 8860-0062-324-XX
0.093 ± 0.010 (2,3 ± 0,3) 8860-0093-100-XX 8860-0093-150-XX 8860-0093-300-XX 8860-0093-324-XX
0.100 ± 0.010 (2,5 ± 0,3) 8860-0100-100-XX 8860-0100-150-XX 8860-0100-300-XX 8860-0100-324-XX
0.125 ± 0.010 (3,2 ± 0,3) 8860-0125-100-XX 8860-0125-150-XX 8860-0125-300-XX 8860-0125-324-XX
ELECTROSEAL™ CONDUCTIVE
ELASTOMER EMI SHIELDING
Laird electrically conductive elastomer products are ideal
for both military and commercial applications requiring
both environmental sealing and EMI shielding. Compounds
can be supplied in molded or extruded shapes, sheet stock,
custom extruded, or die-cut shapes to meet a wide variety of
applications.
Our conductive extrusions offer a wide choice of proles to t
a large range of applications. The cross-sections shown on the
following pages are offered as standard. Custom dies can be
built to accommodate your specic design.
• Available in a wide variety of conductive ller materials
• Shielding effectiveness up to 120 dB at 10 GHz
SHEET MATERIAL
The Table below lists thicknesses and sizes for our molded sheet
material, while Table 3, page 82, shows the compounds available
for all of our conductive silicone elastomers.
HOW TO SPECIFY ECE
Decide on molded sheet stock or extruded shapes. Select the
desired conguration and dimensions from Table 1 (for sheet
stock) or page 85 (for extruded shapes). Select the desired
material from Table 3. Insert material number from Table 3, page
82, in place of the letters XX in the Laird part number.
Example
1. From page 87, for a rectangular strip measuring
0.500 in. (12,7 mm) x 0.075 in. (1,9 mm), part number
is 8861-0130-XX.
2. From Table 3, on page 82, for silver-nickel ller, material
number is 84.
3. Ordering part number is 8861-0130-84.*
Note: Rectangular and D-shaped extrusions can be supplied with
pressure sensitive adhesive tape.
*If pressure sensitive adhesive is required, replace the fth digit with a 9
(i.e. 8861-9130-84).