Datasheet
Standard modules
Supercool’s thermoelectric modules for indus-
trial and commercial applications deliver the
market’s best cooling performance.
By using one or more TEMs, you can design a
cooling system with effects ranging from just
a few Watts all the way up to several hundred
Watts. With max. voltage from 0.9 V up to
30 V DC and an array of pellet geometries,
there’s every chance of fi nding just the right
module for your application. In the event that
our standard range doesn’t meet all your require-
ments, we offer a choice of other dimensions and
pellet geometries. Max. ∆T up to 75°C
(at T
hot
= 25°C).
To optimize service life, maximum warm side
temperature is 80°C.
Sealed versions
We also provide a selection of off-the-shelf stan-
dard TEMs with perimeter sealing.
Silicon moisture sealing: A cost-effective mois-
ture sealing method suitable for most applica-
tions. Add –S after product code
(PE-071-14-15-S)
Epoxy moisture sealing: Moisture and vapor
sealing using special epoxy resin with low ther-
mal conductivity. Add –E after product code
(PE-127-10-13-E)
Sealed modules (-S or –E) available from stock
are given in the table below.
All high performance modules are available in a
sealed version on request.
6
Standard modules
PE-007-14-15 6.0 0.9 3.3 74 0.12 10 10 3.9 200 22
PE-017-10-15 3.4 2.1 4.5 74 0.49 10 10 3.8 200 24
PE-017-14-15 6 2.1 7.6 74 0.29 15 15 3.9 200 22
PE-031-08-15 2.2 3.8 5.1 74 1.57 13 13 3.8 200 24
PE-031-10-08 6 3.8 13.8 72 0.52 15 15 3.1 200 22
PE-031-10-13 3.9 3.8 9.3 74 0.93 15 15 3.6 200 24 S
PE-031-10-15 3.4 3.8 8.1 74 1.03 15 15 3.8 200 24 S
PE-031-14-15 6 3.8 14.5 74 0.48 20 20 3.9 200 22
PE-063-08-15 2.2 7.8 10.4 74 3.20 25 12 3.8 150 24
PE-063-10-15 3.4 7.8 16.5 74 2.03 30 15 3.8 200 24
PE-071-10-08 6 8.8 31.6 72 1.17 20 20 3.1 200 22
PE-071-10-13 3.9 8.8 21.2 74 1.98 20 20 3.6 200 24 S
PE-071-10-15 3.4 8.8 18.5 74 2.18 20 20 3.8 200 24
PE-071-14-11 8.5 8.8 45.8 72 0.83 30 30 3.8 200 20
PE-071-14-15 6 8.8 33.2 74 1.27 30 30 3.9 200 22 S
PE-071-14-25 3.9 8.8 21.6 75 1.88 30 30 4.8 200 22
PE-071-20-15 13.1 8.8 71.9 74 0.55 47 47 4.6 200 20
PE-127-08-15 2.2 15.7 20.9 74 6.2 25 25 3.8 200 24
PE-127-08-25 1.3 15.7 12.6 75 11.0 25 25 4.8 200 24 S
PE-127-10-08 6 15.7 57.1 72 2.23 30 30 3.1 200 22 S
PE-127-10-13 3.9 15.7 37.9 74 3.46 30 30 3.6 200 24 S, E
PE-127-10-15 3.4 15.7 33.2 74 4.02 30 30 3.8 200 24
PE-127-10-25 2 15.7 19.7 75 6.7 30 30 4.8 200 24
PE-127-14-11 8.5 15.7 82.1 72 1.54 40 40 3.8 300 20 S, E
PE-127-14-15 6 15.7 59.4 74 2.23 40 40 3.9 300 22 S, E
PE-127-14-25 3.9 15.7 38.6 75 3.36 40 40 4.8 350 22 S, E
PE-127-20-15 13.1 15.7 128.7 74 1.08 62 62 4.6 200 20
PE-127-20-25 8 15.7 78.7 75 1.68 62 62 5.6 200 20
PE-131-10-13 3.9 16.2 39.1 74 3.65 40 23 3.6 200 24 S
PE-161-12-10 6.7 20.0 83.9 72 2.44 40 40 3.3 350 22 S
PE-161-12-13 5 20.0 62.3 74 3.34 40 40 3.7 350 22 S
PE-161-12-15 4.4 20.0 54.6 74 3.87 40 40 3.9 350 22 S
PE-241-10-13 3.9 30.0 71.8 74 6.6 40 40 3.6 200 24
PE-241-10-25 2 30.0 37.3 75 12.7 40 40 4.8 300 24 S
PE-241-14-15 6 30.0 112.7 74 4.21 55 55 3.9 200 22
Product No.
P
c
max
(W)
U
max
(V)
I
max
(A)
S
AWG #
ABHL
(mm)∆T
max
(°C)
• Lead wires are approved acc. to UL 1569.
• R
AC
tolerance = ±10%
• Tolerance of I
max
, U
max
, Q
max
= ± 5%
R
AC
(ohm)
1) S = Silicon sealed version available. E = Epoxy sealed version available. Note! Max ∆T is reduced by
2-3°C for S-type and 1-2°C for E-type.
Available
Sealing
1
HIGH PERFORMANCE SERIES