Datasheet

Multistage modules
PE-010-0606-1111 1.1 0.9 0.35 92 0.64 3.2 3.2 3.9 3.9 4.2 50 0.07
1)
PE-024-0606-1111 1.1 2.2 0.81 92 1.47 4.1 4.1 6.1 6.1 4.6 50 0.07
1)
PE-049-1010-1515 2.1 3.8 3.4 87 1.53 11.5 11.5 15 15 6.6 200 24
PE-049-1414-1515 4 3.8 3.7 87 0.83 15 15 20 20 7.2 200 22
PE-107-1010-1212 3 9.2 9.2 89 2.72 22.6 22.6 22.6 22.6 6.25 200 24
PE-190-1010-1212 2.8 15.7 16.4 87 4.78 30 30 30 30 6.5 200 24
PE-192-1420-1118 6.7 15.6 39.9 87 2.15 40 40 40 40 8.1 300 20
PE-192-1420-1525 4.4 16.0 27.3 88 3.03 40 40 40 40 8.1 300 22
PE3-070-20-25 6.5 6.5 3.0 118 0.93 14 8 36 36 16 200 22
PE3-119-14-15 3.9 8.0 7.5 100 2.09 15 15 30 30 10.4 200 22
PE3-119-20-15 8 8.2 14.9 100 0.97 22 22 44 44 12.9 200 20
PE3-231-10-15 1.9 15.5 6.9 104 7.22 15 15 30 30 9.5 200 24
PE4-115-14-15 3.5 7.6 2.6 122 1.95 14.5 4.5 33 24 13.8 200 22
PE4-129-10-15 1.8 8.2 1.9 115 3.83 8 8 23 23 12.5 200 24
PE5-257-10-15 1.5 14.5 2.0 123 7.9 8 8 30 30 15.4 200 24
(mm)
8
Product No.
P
c max
(W)
U
max
(V)
I
max
(A)
S
AWG #
Ac Bc
ABHL
∆T
max
(°C)
Center hole modules
Center hole modules are used when light, wires or
other hardware need to be transferred through the
module.
We only stock a limited number of modules of this
type. Let us know about the challenges of your ap-
plication, and we’ll make sure you get just the right
module. In principle, all modules can be supplied
with a center hole.
Operating temperature is max. 80°C.
Multistage modules
Thanks to superior material characteristics we can
offer a range of truly outstanding multistage TEMs.
If your system has to generate a ∆T above 50°C, you
normally need a multistage module. Typical applica-
tions include CCD arrays, IR detectors and analytical
instruments.
If you can’t fi nd the right TEM for your application,
feel free to put our designers to the test.
Operating temperature is max. 80°C.
Center hole modules
PE-119-10-13HS
1)
3.9 14.7 35.5 71 3.37 30 4.7 3.6 200 24
PE-125-14-11HS
1)
8.5 15.6 81.5 70 1.46 40 4.7 3.8 300 20
PE-125-14-15HS
1)
6 15.5 58.5 72 2.16 40 4.7 3.9 300 22
PE-014-14-25RH
2)
3.9 1.7 4.3 75 0.37 26 14 4.7 200 22
PE-032-14-15RH
2)
6 4.0 15 74 0.54 55
3)
27 3.9 200 22
PE-038-10-13RH
2)
3.9 4.7 11.4 74 1.05 24 10 3.6 200 24
Product No.
P
c max
(W)
U
max
(V)
I
max
(A)
A, B, D d
(mm)∆T
max
(°C)
1)
S = Silicon sealed versions.
2)
Round design. D = outer diameter and d = inner diameter.
3)
Outer diameter on warm side = 55 mm. Outer diameter on cold side = 44 mm.
HIGH PERFORMANCE SERIES
• Lead wires are approved acc. to UL 1569.
• R
AC
tolerance = ±10%
• Tolerance of I
max
, U
max
, Q
max
= ± 5%
R
AC
(ohm)
• Lead wires are approved acc. to UL 1569..
• R
AC
tolerance = ±10%
• Tolerance of I
max
, U
max
, Q
max
= ±5%
R
AC
(ohm)
HL
S
AWG #
1) Tefl on insulated wire. Cross section in mm
2