Combination Outfit For General Water Analysis Test Kit Instruction Manual Code 4783-03 Code 3590-03
USE OF THE OCTA-SLIDE 2 VIEWER The Octa-Slide 2 Viewer should be held so non-direct light enters through the back of the Viewer. Insert the reacted sample into the top of the Viewer. Slide the Octa-Slide 2 Bar into the Viewer and match the color of the reaction to the color standards. 1 2 3 Insert the OctaSlide 2 Bar into the Octa-Slide 2 Viewer (1101). Insert test tube into the Octa-Slide 2 Viewer (1101). Match sample color to a color standard. Record results.
COMBINATION WATER OUTFIT CODE 4783-03 CODE 3590-03 QUANTITY 15 mL 100 60 mL 30 mL 4.5 g 30 mL 30 mL 15 mL 60 mL 1 1 4 (6†) 1 1 1 1 1 CONTENTS *Hardness Reagent #5 Hardness Reagent #6 Tablets Hardness Reagent #7 *Iron Reagent #1 *Iron Reagent #2 Powder *Wide Range Indicator *Sulfide Reagent A *Sulfide Reagent B Sulfide Reagent C Test Tube, w/cap Spoon, 0.05 g, plastic Test Tubes, plastic, 2.5-5-10 mL, w/caps Pipet, 1.0 mL, plastic Iron Octa-Slide 2 Bar, 0.5-10.0 ppm Wide Range pH Octa-Slide 2 Bar, 5.0-10.
TOTAL HARDNESS TEST PROCEDURE 1 Fill the test tube (4488) to the desired line with the sample water, upper line: 1 drop = 10 ppm CaCO3 middle line: 1 drop = 1 gpg CaCO3 lower line: 1 drop = 20 ppm CaCO3. 3 2 Add 5 drops of *Hardness Reagent #5 (4483). Swirl to mix. 5 4 Add 1 Hardness Reagent #6 Tablet (4484). Swirl until tablet has disintegrated. Solution will turn Red if hardness is present. Proceed to next step. If solution is Blue, there is no measurable amount of hardness.
IRON TEST PROCEDURE 2 1 Rinse test tube (0106) with sample water. Fill to 5 mL line. Add 5 drops of *Iron Reagent #1 (4450). 4 3 Cap and mix. Use the 0.05g spoon (0690) to add one level measure of *Iron Reagent #2 Powder (4451). 6 5 Wait 3 minutes. 3 Cap and shake until powder dissolves. 7 9 Insert the Octa-Slide 2 Bar (4448-01) into the OctaSlide 2 Viewer (1101). Match sample color to a color standard. Record results as ppm iron.
pH TEST PROCEDURE 2 1 Fill a test tube (0106) to the 10 mL line with sample water. 3 5 Cap and mix. Insert test tube into the OctaSlide 2 Viewer (1101). Add 8 drops of *Wide Range pH Indicator (2218). 4 6 Insert Wide Range pH Octa-Slide 2 Bar (3483-01) into the Octa-Slide 2 Viewer (1101). Match sample color to a color standard. Record as pH.
TOTAL SULFIDE TEST PROCEDURE † Supplied only with Code 3590-03 Note: Collect sample with a minimum of aeration and analyze promptly. 1 2 Fill a test tube (0106) to the 5 mL line with the sample water. 3 Add 15 drops of *Sulfide Reagent A (4458). 4 Add 3 drops of *Sulfide Reagent B (4459). Cap and gently invert to mix. Cap and mix. 5 6 Use the pipet (0354) to add 1.0 mL of Sulfide Reagent C (4460). Wait 1 minute.
LaMOTTE COMPANY Helping People Solve Analytical Challenges PO Box 329 • Chestertown • Maryland • 21620 • USA 800-344-3100 • 410-778-3100 (Outside USA) • Fax 410-778-6394 Visit us on the web at www.lamotte.
