Use and Care Manual

Uses:
Acrylic Primer Sealer
TM
is specially formulated
to penetrate and seal internal cracks and
porous surfaces such as concrete. Also
recommended to seal and protect exposed
architectural concrete exposed aggregate
sidewalks, ornamental stone and precast
concrete.
Notice: The technical data contained herein are
true and accurate to the best of our knowledge.
Published technical data and instructions are
subject to change without prior notice.
S.D.S.: Available upon request.
Wood and plywood: Sand rough areas and prime properly. Maximum
acceptable moisture content prior to coating new wood should be under
16%.
Method of Application:
Stir thoroughly before using. Paint always on shaded side of the building. Do
not dilute paint, use as supplied. Do not apply when surface or air
temperature is below 50 ˚F or if rain is expected within 5 hours. Apply
product with brush, roller or sprayer. Apply generously with a full brush or
roller and avoid excessive brushing or spreading too thinly. Typical standard
practice recommends intermixing when working with more than one
container of the same color, to ensure color consistency.
Test pH levels: Levels of pH should be under 9 prior to the application of
any paint or primer. If pH level is above 9 but below 13, apply Lanco
®
100%
Acrylic Roof & Wall Primer/Sealer AS-210 as per instructions prior to the
application of additional primers and/or finish coats.
Mixing and thinning: Mix always thoroughly before application. Thinning is
not recommended, if necessary use only 8oz. of water per gallon of this
product.
Brush: Use a good quality nylon PA-1982 or polyester brush PA-1999.
Roller: Use a Lanco
®
All-Purpose 3/8” Nap Roller PA-566. Apply
generously, but avoid excessive brushing or reworking of painted areas, do
not apply or spread too thinly.
Spray: Spray equipment should be capable of maintaining a pressure of
700-1000 psi with a tip of 0.015 to 0.019. Spray and back roll on rough or
porous surface to achieve required film build. Apply two coats with
overnight drying between coats to minimize pinholes on the surface is
recommended. See equipment’s manufacturer recommendation.
Precaution: Do not apply when air or surface temperature is below
50˚F(10˚C). Apply liberally,but do not overspread. Stop painting at least two
hours before you expect dew to form or the temperature to fall below
50˚F(10˚C).
Important: It is important that you apply one coat of primer and two full
coats of paint to achieve the warranty protection.
Limited warranty: The manufacturers liability in connection with the sale of
this product extend only to the replacement price if it should fail to comply
with quality standards or specifications.
Caution: Harmful if swallowed. Contains acrylic resin. In case of eye contact,
flush thoroughly with water. Do not rub eyes. In case of skin contact, flush
area immediately with clean water. If swallowed, do not induce vomiting.
Consult a physician immediately. Use only with adequate ventilation.
Adequate ventilation required when sanding or abrading the dried film.
Always use (NIOSH/MSHA TC21C or equivalent.) Goggles are
recommended while handling the product. This product may contain
chemicals known to the State of California to cause cancer and birth defects
or other reproductive harm. Keep out of reach of children.
Warning! If you scrape, sand, or remove old paint, you may release lead
dust. Lead is toxic. Exposure to lead dust can cause serious illness, such as
brain damage, especially in children. Pregnant women should also avoid
exposure. Wear a NIOSH-approved respirator to control lead exposure.
Clean up carefully with a HEPA vacuum and a wet mop. Before you start,
find out how to protect yourself and your family by contacting the National
Lead Information Hotline at 1-800-424-LEAD or log on to
www.epa.gov/lead. For chemical emergency call ChemTrec
1-800-424-9300. Protect from freezing.
• NORTH AMERICA • 600 Mid Florida Drive Airport Industrial Park of Orlando, Florida 32824 • Tel. [phone] Fax [phone]
• CARIBBEAN & SOUTH AMERICA • Urb. Aponte #5, San Lorenzo, Puerto Rico USA 00754 • Tel. [phone] Fax [phone]
• CENTRAL AMERICA • Zona Industrial Bes, lote #4, El Coyol de Alajuela, Costa Rica • Tel. [phone] Fax [phone]
Page 2 Acrylic Primer Sealer AS-210 Rev. 06/ 2016