TDS

Concrete Adhesive
Concrebond CB1797 • CB1798
Description
Product Advantages
• Water resistant
• Excellent coverage
• Water cleanup
• Fast-drying
• Brush & roller application
• Excellent bond strength
• Does not contain harmful solvents
• Non-flammable
Use
For comercial and construction use only, to
provide a permanent bond between the cement
plaster mix and structurally sound substrates.
Adheres to porous and non-porous surfaces:
• Wood
• Concrete
• Old or existing plaster
• Wallboard
• Interior roof ceilings
• Lime plaster
Surface Preparation
All surfaces to be bo
nded must be clean, dry
and free of contaminants such as dust,
sand, oil and grease films.
Product Data
Notice: The technical data contained herein are
true and accurate to the best of our knowledge.
Published technical data and instructions are
subject to change without prior notice.
S.D.S.: Available upon request.
Storage
Protect from freezing; store in a cool, dry place
at room temperature. Product must be used
within one year of purchase.
Mixing:
Always mix thoroughly by hand or with a
power agitator before application.
Cleanup:
Clean all equipment immediately after use with
warm soapy water. Completely flush all spray
equipment with this solution.
Application
For satistactory bonding, follow the procedure:
1. Stir contents of container thoroughly before
use. Do not dilute to make volume.
2. Surface should be free of dust, sand or
foreign matter.
3. Apply a uniform coat to the surface by brush,
roller or spray gun.
4. Before applying the concrete plaster, check
surface for uniformity of color. Areas that are
irregular in shade indicate an insufficient
amount of bonding has been applied.
5. Allow at least two hours for bonding to cure
before applying concrete plaster.
6. If cured 24 hours, apply an additional coat
before applying concrete plaster.
7. Always maintain the proper level of water in
the concrete plaster mix. Do not apply too dry.
8. When troweling the concrete plaster, use a
circular motion follow through on all strokes.
Never pull the trowel away perpendicular to the
surface.
Danger/Warning
Use only with adequate ventilation. Ventilation
must be sufficient to limit exposure below
S.D.S. limits.
Caution:
Do not take internally. Close container after
each use. KEEP OUT OF REACH OF
CHILDREN. Do not take Internally.
For chemical emergency call ChemTrec
1-800-424-9300 (USA) ó 1-703-527-3887
(International).
LIMITATIONS & MORE INFORMATION:
Read Safety Data prior to use.
Go to www.lancopaints.com.
Protect from freezing.
T E C H N ICA L DATA SHEET
Product Type:
Finish color:
Drying time:
Sizes:
Thinning:
VIscosity:
Flash Point:
Coverage
VOC:
Vinyl Acetate Homopolymer
White CB1797
Blue CB1798
20 minutes - To Touch
2 hours - To Plaster
3.5 gallons
1 gallon
Is not recommended
1000 - 1200 CPS
Non-flammable
200 sq.ft./gal.
<50 G/l
www.lancopaints.com
Concrebond Bonding Agent CB1797 ● CB
1798 is a concrete bonding adhesive for
interior or exterior use, to bond new concrete
to old without laborious scarification process
which is usually necessary. It withstands
humidity and can be applied over damp or dry
surfaces and is not affected by alkalinity of lime
plaster or Portland cement. Available in white
or blue.
• NORTH AMERICA • 600 Mid Florida Drive Airport Industrial Park of Orlando, Florida 32824 • Tel. [phone] Fax [phone]
• CARIBBEAN & SOUTH AMERICA • Urb. Aponte #5, San Lorenzo, Puerto Rico USA 00754 • Tel. [phone] Fax [phone]
• CENTRAL AMERICA • Zona Industrial Bes, lote #4, El Coyol de Alajuela, Costa Rica • Tel. [phone] Fax [phone]
Rev
. 7 / 2020