Use and Care Manual

Page 2
Dura-Life Clear (WL-2823)
Rev. 06/2017
• NORTH AMERICA • 600 Mid Florida Drive Airport Industrial Park of Orlando, Florida 32824 • Tel. [phone] Fax [phone]
• CARIBBEAN & SOUTH AMERICA • Urb. Aponte #5, San Lorenzo, Puerto Rico USA 00754 • Tel. [phone] Fax [phone]
•
CENTRAL AMERICA
•
Zona Industrial Bes, lote #4, El Coyol de Alajuela, Costa Rica
•
Tel. [phone] Fax [phone]
Surface Preparation
Surface must be completely dry and in sound
condition. All surfaces must be clean and free of
contaminants such as form and release agents, dirt,
grease, oil, rust, chalk, efflorescence, organic growth,
mildew and non-adherent material. Gloss finishes should
be sanded or de-glossed. Feather sand rough edges and
spot prime bare areas. Any deteriorated or failed sealant
and/or patching compound should be removed and
replaced. Fill cracks and voids with Lanco
®
Rain-Shield
TM
Elastomeric Crack Filler. Apply sealants or patching
compounds over a primed surface and at a safe level of
pH.
New concrete mortar joints must have cured for a
minimum of 30 days before applying clear sealer.
Previously sealed areas must be porous in order to apply
clear sealer. To test for porosity, place a few drops of
water on or other methods in order to provide a sound
surface. Apply a full coat of primer as recommended
under New Surfaces.
MILDEWED SURFACES: Any existing mildew on the
surface must be killed and removed prior to the
application of this product. Any mildew not removed may
continue to grow through the new finish. Using a long-
handled brush, scrub mildewed surfaces with a mixture of
one quart of household bleach and three quarts of warm
water. Allow the solution to remain on the surface for 10
minutes. Rinse thoroughly with water and allow the
surface to dry before painting. Wear protective eyewear,
waterproof gloves, and protective clothing. Quickly wash
off any of the mixture that comes in contact with your
skin. Do not add detergents or ammonia to the bleach /
water solution.
General Information
PRECAUTION: For exterior use only. Do not add mineral
spirits or other solvents to this product. Do not apply when
surfaces or air temperature are below 50°F (10°C). Do not
expose to freezing temperatures in storage. Do not use on
unpainted ferrous metal. Do not use on staining wood such
as cedar, mahogany, or redwood.
LIMITED WARRANTY: The manufacturers liability in
connection with the sale of this product extend only to the
replacement price if it should fail to comply with quality
standards or specifications.
CAUTION: Harmful if swallowed. Contains Acrylic Resin. In
case of eye contact, flush thoroughly with water. Do not
rub eyes. In case of skin contact, flush area immediately
with clean water. If swallowed, do not induce vomiting.
Consult a physician immediately. Use only with adequate
ventilation. Adequate ventilation required when sanding or
abrading the dried film. Always use NIOSH/MSHA TC21C or
equivalent.) Goggles are recommended while handling the
product. Keep out of reach of children.
WARNING! If you scrape, sand, or remove old paint, you
may release lead dust. Lead is toxic. Exposure to lead dust
can cause serious illness, such as brain damage, especially
in children. Pregnant women should also avoid exposure.
Wear a NIOSH-approved respirator to control lead
exposure. Clean up carefully with a HEPA vacuum and a
wet mop. Before you start, find out how to protect yourself
and your family by contacting the National Lead
Information Hotline at 1-800-424-LEAD or log on to
www.epa.gov/lead
. For chemical emergency call ChemTrec
1-800-424-9300. PROTECT FROM FREEZING.
S.D.S.: Available upon request.
The information presented on this Technical Data Sheet is based on testing
conducted by Lanco
®
Paints &
Coatings. No guarantee of accuracy,
comprehensiveness, or performance is given or implied. Information and
recommendations are subject to change dependent on surface conditions
(substrate), weather and method of application. Please consult with a Lanco
Re
presentative or visit www.lancopaints.com for complete, up-to-
date technical
information.