Quick Start Guide
MOUNTING AND CONNECTING THE DEVICE
TECHNICAL DETAILS
LANCOM, LANCOM Systems and LCOS are registered trademarks. All other names or descriptions used may be trademarks or registered
trademarks of their owners. Subject to change without notice. No liability for technical errors and/or omissions. 111641/0418
Hardware
Power supply 12 V DC, external power adapter (230 V); bayonet connector to secure against disconnection
Power consumption Max. ca. 14 W
Environment Temperature range 0–35 °C; humidity 0–95 %; non-condensing
Housing Robust synthetic housing, rear connectors, ready for wall mounting, Kensington lock; measures
210 x 45 x 140 mm (W x H x D)
Number of fans None; fanless design, no rotating parts, high MTBF
Interfaces LANCOM R883VAW over ISDN
WAN: VDSL2 a VDSL2 as per ITU G.993.2; proles 8a, 8b, 8c, 8d, 12a, 12b, 17a;
a Compatible to VDSL2 from Deutsche Telekom
a ADSL conformity according to: ADSL2+ over ISDN as per ITU G.992.5 Annex B/J with DPBO,
ADSL2 over ISDN as per ITU G.992.3 Annex B, ADSL over ISDN as per ITU G.992.1 Annex B.
a Supports just one virtual connection at a time in ATM (VPI-VCI pair)
Wi-Fi a Frequency band: 2400-2483.5 MHz (ISM) or 5150-5825 MHz (restrictions vary between
countries)
a Radio channels 2.4 GHz: Up to 13 channels, max. 3 non-overlapping (2.4-GHz band)
a Radio channels 5 GHz: Up to 26 non-overlapping channels (channels available vary
according to country regulations; DFS for automatic dynamic channel selection required)
ETH 4 individual ports, 10 / 100 / 1000 Mbps Gigabit Ethernet, by default set to switch mode.
Up to 3 ports can be operated as additional WAN ports. Ethernet ports can be electrically
disabled in the LCOS conguration.
USB USB 2.0 hi-speed host port for connecting USB printers (USB print server),
serial devices (COM-port server) or USB drives (FAT le system)
ISDN 1 / ISDN 2 ISDN 1: Internal (NT) or external (TE) ISDN bus. This feature is controlled by LCOS. According to
the settings, connect the light-blue ISDN cable either to the NTBA or the ISDN terminal device.
ISDN 2: Internal (NT) ISDN bus. Use the light-blue ISDN cable to connect the ISDN device to
the ISDN interface.
Analog 1 / Analog 2 Use the cable of your analog devices to connect them with the analog interfaces. If necessary,
use the enclosed adapter.
Cong (Com) / V.24 Serial conguration interface/COM-port (8-pin mini-DIN): 9,600 - 115,200 baud, suitable for
optional connection of analog/GPRS modems. Supports internal COM-port server and provides
transparent asynchronous serial-data transfer via TCP.
WAN protocols
VDSL, ADSL, Ethernet PPPoE, PPPoA, IPoA, Multi-PPPoE, ML-PPP, PPTP (PAC or PNS) and IPoE (with or without
DHCP), RIP-1, RIP-2, VLAN
ISDN DSS1 (Euro-ISDN), PPP, X75, HDLC, ML-PPP, V.110/GSM/HSCSD
Declaration of Conformity
Hereby, LANCOM Systems declares that this radio equipment is in compliance with Directive 2014/53/EU. The full text
of the EU declaration of conformity is available at the following internet address: www.lancom-systems.com/ce/
Package content
Manual Quick Reference Guide (DE/EN); Installation Guide (DE/EN)
Cable 1 Ethernet cable, 3m (kiwi colored connectors); 1 DSL cable for an IP-based line, 4.25m;
1 ISDN cable, 3m (light-blue connectors)
Adapters 2 TAE adapters (RJ11 - TAE)
Power adapter External power supply adapter (230 V); NEST 12 V / 1.5 A DC/S; barrel connector 2.1 / 5.5 mm
bayonet; LANCOM item no. 111301
This product contains separate open-source software components which are subject to their own licenses, in particular
the General Public License (GPL). The license information for the device rmware (LCOS) is available on the device‘s
WEBcong interface under “Extras > License information“. If the respective license demands, the source les for the
corresponding software components will be made available on a download server upon request.
i VPN
Off VPN connection inactive
Green, permanently VPN connection active
Green, ashing VPN connecting
e ISDN
Off Interface deactivated
Green, permanently D-channel active
Green, ickering ISDN data transfer
Red, ickering ISDN transfer error
Red/orange, blinking ISDN hardware error
b Online
Off WAN connection inactive
Green, permanently WAN connection active
Red, permanently WAN connection error
c DSL
Off Interface deactivated
Green, permanently DSL connection active
Green, ickering DSL data transfer
Red, ickering DSL transfer error
Red/orange, blinking DSL hardware error
Orange, blinking DSL training
Orange, permanently DSL sync
Green, blinking DSL connecting
d Analog
Off Interface deactivated
Green, permanently Interface activated
Orange, blinking Incoming call
Green, blinking Connection active
h VoIP
Off No SIP accounts dened or VCM is off
Green, permanently All dened and active SIP accounts
(outgoing) were successfully registered
Red, permanently Not all dened and active SIP accounts
were registered (possibly still in process)
Red or green,
inverse ashing
Number of currently used lines (connecting
or connected)
f ETH
Off No networking device attached
Green, permanently Connection to network device operational,
no data trafc
Green, ickering Data transmission
g WLAN
Off No Wi-Fi network dened or Wi-Fi module
deactivated. The Wi-Fi module is not
transmitting beacons.
Green, permanently At least one Wi-Fi network is dened and
Wi-Fi module activated. The Wi-Fi module
is transmitting beacons.
Green, blinking DFS scanning or other scan procedure
j Reset
Reset switch
Operated e.g. with a paper clip
a short press: Restart the device
a long press: Reset the device
a Power
Off Device switched off
Green, permanently* Device operational, resp. device paired /
claimed and LANCOM Management Cloud
(LMC) accessible
Red/green blinking Conguration password not set. Without a
conguration password, the conguration
data in the device is unprotected.
Red blinking Charge or time limit reached
1x green inverse
blinking*
Connection to the LMC active, pairing OK,
device not claimed
2x green inverse
blinking*
Pairing error, resp. LMC activation code
not available
3x green inverse
blinking*
LMC not accessible, resp. communication
error
LANCOM R883VAW
DSL
ETH 2
Power
ETH 1
Online
ISDN 1
ETH 4
ETH 3
VPN
Analog 1
Analog 2
ISDN 2
WLAN
Reset
VoIP
a c eb gfd ih j
LANCOM R883VAW
Quick Reference Guide
*) After a rmware upgrade to LCOS 10.14 the additional power LED
statuses are displayed in 5-seconds rotation if the device is
congured to be managed by the LANCOM Management Cloud.
Gigabit Ethernet 10/100/1000
ISDN 1 ISDN 2
TE / NT NT
VDSL
Analog 1Analog 2
a b c d e f
g
4
Please observe the following when setting up the device
A Do not rest any objects on top of the device
A For devices to be operated on the desktop, please attach the
adhesive rubber footpads
A In case of wall mounting, use the drilling template as supplied
A Keep the ventilation slots on the side of the device clear
of obstruction
A Rack installation with the optional LANCOM Rack Mount
(separately available)
LANCOM 1681V
Power
VDSL
Online
ETH 1
ETH 2
VPN
ETH 3
ETH 4
ISDN Status
a
VDSL interface
Use the supplied DSL cable for the IP-based line to connect the
VDSL interface and the provider’s telephone socket. For more
infor mation, please contact your Internet service provider.
b
Ethernet interfaces
Use the cable with the kiwi-colored connectors to connect one of
the interfaces ETH 1 to ETH 4 to your PC or a LAN switch.
c
Analog interfaces
Connect analog terminal devices to the analog interfaces either
directly via RJ11, or with the help of the enclosed TAE adapters.
d
Conguration interface
Use a serial conguration cable to connect the serial interface
(COM) to the serial interface of the device you want to use for
conguring / monitoring (separately available).
e
ISDN interfaces
ISDN 1:
Internal (NT) or external (TE) ISDN bus.
This feature is controlled by LCOS.
ISDN 2:
Internal (NT) ISDN bus.
A 100-Ohm resistor for line termination is
switchable in LCOS.
f
USB interface
You can use the USB interface to connect a USB printer or a
USB memory stick.
g
Power
After connecting the cable to the device, turn the bayonet
connector 90° clockwise until it clicks into place.
Use only the supplied power adapter.
g