User Manual

ManualsBrandsLand of Nod ManualsFurnitureVERONA CRIB

Thank you for selecting a ducduc for nod product.

Keep instructions for future use.

Please check contents against the components list in

these instructions. Also, please ensure there was no

damage that may have occurred in shipping. if any

compenents are missing or you find any damage,

please contact The Land of Nod at 800-933-9904

before continuing.

Read all the instructions before use of the CRIB.

Please remember to securely tighten all bolts and

fasteners and periodically check to make sure every

component is properly and securely in place.

Pay close attention to the safety warnings in these

instructions and on CRIB labels.

A minimum of two people is required to safely

assemble and move the CRIB. Do not attempt to

move this CRIB alone - dragging or sliding it across

the floor may cause structural damage.

VERONA CRIB

CAUTION:

Any mattress

used in this CRIB must be

at least 27 1/4 inches by 51

5/8 inches with a thickness

not exceeding 6 inches.

Summary of content (10 pages)

PAGE 1
Thank you for selecting a ducduc for nod product. Please check contents against the components list in these instructions. Also, please ensure there was no damage that may have occurred in shipping. if any compenents are missing or you find any damage, please contact The Land of Nod at 800-933-9904 before continuing. Read all the instructions before use of the CRIB.
PAGE 2
PAGE 3
1 Lay SIDE PANEL down with holes facing up. Attach CRIB LEG to SIDE PANEL with one RAIL CONNECTOR BOLT , LOCKING WASHER , and REGULAR WASHER . Tighten with ALLEN WRENCH REPEAT FOR ACCENT PANEL .. . F L.2 K.2 G 2 Align the BASE I so that the sticker “Bottom” is facing the floor. The side of BASE two corner holes should be aligned against SIDE PANEL as shown. I with only While SIDE PANEL is laying down, attach BASE with two BASE CONNECTOR BOLTS LOCKING WASHERS and REGULAR WASHERS .
PAGE 4
3 Place SIDE RAIL onto BASE with rail connector holes facing SIDE PANEL . Attach ACCENT PANEL to crib SIDE RAIL and secure in place with two RAIL CONNECTOR BOLTS , LOCKING WASHERS , and REGULAR WASHERS as shown below. Tighten all bolts with ALLEN WRENCH . Back A.2 I accent panel connector holes K.2 K.
PAGE 5
4 Place END RAIL onto BASE with mattress support holes facing the bottom and inside of crib. Secure END PANEL to BASE with BASE CONNECTOR BOLTS , LOCKING WASHERS , and REGULAR WASHERS from underneath as shown below. Place other END RAIL on the opposite side with mattress support holes facing the bottom and inside of crib. Secure END RAIL to BASE with BASE CONNECTOR BOLTS , LOCKING WASHERS , and REGULAR WASHERS from underneath as shown below.
PAGE 6
5 Line up the rail connector holes on SIDE PANEL with the rail connector holes on the END RAILS . Attach LOCKING WASHERS and REGULAR WASHERS to RAIL CONNECTOR BOLTS and insert and slightly tighten the four RAIL CONNECTOR BOLTS with ALLEN WRENCH . rail connector holes L.2 B F K.2 A.1 Back 2 F L.2 1 L.2 K.2 rail connector holes 6 Line up the rail connector holes on SIDE RAIL with rail connector holes on END RAIL .
PAGE 7
Tighten bolts all the way. The MATTRESS SUPPORT PANEL may be installed in one of four positions. See the four different mattress support holes in each corner of the CRIB. First, select the desired mattress height. Then, unscrew the MATTRESS SUPPORT PIN from each MATTRESS SUPPORT BOLT . Insert the smooth ends of each MATTRESS SUPPORT PIN in the desired mattress support holes on END RAILS . See drawing for proper pin orientation. Back 8 Carefully lower MATTRESS SUPPORT PANEL with labels facing up.
PAGE 8
9 Attach one LOCKING WASHER and one REGULAR WASHER on top of each MATTRESS SUPPORT PIN . Secure and tighten each of the four MATTRESS SUPPORT . Use SCREWDRIVER to BOLTS to each of the four MATTRESS SUPPORT PINS tighten securely. D K.1 L.1 E 10 C Press firmly in center of MATTRESS SUPPORT PANEL to ensure proper placement. In the event MATTRESS SUPPORT PANEL does not appear to be secure remove and repeat steps 7 to 9. The MATTRESS SUPPORT PANEL must be firmly attached at all four corners.
PAGE 9
operation Th e m a ttress heig ht sho uld b e lo we re d a s yo u r ba by g ro ws t o e n s u re t h a t h e/ s h e does no t climb o ut of t h e CR IB . W h e n c h ild is a ble t o pu ll t o a s tan d i ng po sition, set mattres s t o lo we s t po s it io n a n d re mo ve bu mbe r pa d s, l arge toy s, and other objects t h a t c o u ld s e r ve a s s t e ps f o r c limbin g o u t . Regu l arly asses y o ur baby ’s a bilit ie s a n d ma k e a dju s t me n t s a c c o rdin g ly.
PAGE 10
Failure to follow these warnings and the assembly instructions could result in serious injury or death. Read all instructions before assembling crib. KEEP INSTRUCTIONS FOR FUTURE USE. Infants can suffocate on soft bedding. Never add a pillow or comforter. Never place additional padding under infant. To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep, unless otherwise advised by your physician.