User Manual

ManualsBrandsLandoll ManualsSpecial machinery174282 FRAME REPLACEMENT KIT

F-695 Edition Brillion Farm Equipment 1-1

rev01-04-13 Landoll Corporation

INSTALLATION INSTRUCTIONS FOR

FRAME REPLACEMENT KIT P/N 174282

ON WFP22-36 (WING FLOAT PULVERIZERS)



CAUTION

• Identify the parts listed below.

• Place the Wing Float Pulverizer in a suitable area

to work with the frame while the wings are

unfolded.

• Make sure all hydraulic pressure is neutralized.

NOTICE

Do not work on or under this machine unless

securely

blocked and supported by a hoist or

tractor or by other sufficient means!

Understand the procedure before doing the work.

Use proper tools and equipment.

Kit 174282 - Parts List

ITEM PART NUMBER DESCRIPTION QTY

174282 KIT, WFP22-36 FRAME REPLACEMENT

1 1-557-010362-65 PIN COTTER, 1/4X2-1/2 ZP 1

2 1-647-010004255 PIN, SPRING, SLOTTED 3/8X2 3

3 1-654-010061-06 SCREW,HXCP, 3/4-10UNCX2-1/4GR5 12

4 1-861-010034-17 WASHER, LKG, HLCL SPR, 3/4 12

5 1-861-010034-21 WASHER, LKG HEL SPRG 6

6 1J136 SPRAY CAN RED PAINT 1

7 1J548 SPRAY CAN BLACK PAINT 1

8 107-0814 RIVET 1/8X1/8 ALUM POP 2

9 110-4224 PIN,COTTER 3/16 X 2IN LG 2

10 137943 SCREW,HEX CAP 1-8UNCX2-1/4GR5 6

11 140477 BEARING, DISC 1.775 ID ASSY 6

12 140479 MOUNT, TRUNNION BEARING 12

13 147072 PIN, SPRING SLOTTED 5/16 X 2 6

14 154185 WASHER, 3/8 6

15 154186 WASHER, FLAT TOP 6

16 171738 WASHER, SHIM 11 GA, 1.79 ID 6

17 171739 WASHER, SHIM 14 GA, 1.79 ID 6

18 171876 PIN, 1” W/KEEPER WELD 3

19 173119 SHAFT-STUB, AXLE, WELDMENT 6

20 173359 WASHER, FLAT, 1.063X2X1/4 ZP 6

21 174879 BOLT ON BEARING HANGER 2

22 174880 PLATE-BEARING MOUNT 2

23 175095 FRAME, WFP22-36 CENTER 1

24 2P225 STRAP, SCRAPER 1

25 7K678 CABLE TIE 15

26 9D674 HOSE TIE - 8” 4

27 9J437 CLEVIS PIN, 1/2X6 1

28 F-695 INSTALLATION INSTRUCTIONS FOR KIT 174282 1

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR FRAME REPLACEMENT KIT P/N 174282 ON WFP22-36 (WING FLOAT PULVERIZERS)  CAUTION NOTICE Do not work on or under this machine unless securely blocked and supported by a hoist or Understand the procedure before doing the work. Use proper tools and equipment. tractor or by other sufficient means! • Identify the parts listed below. • Place the Wing Float Pulverizer in a suitable area to work with the frame while the wings are unfolded.
PAGE 2
The top corner of the wheel arms on the transport axle rockshaft must be trimmed to provide under frame clearance on the P/N 171861 (new) center frame. See Figure 1-1 for detailed dimensions. • Touch up the effected area with Brillion paint.  WARNING Failure to Trim the Wheel Arm will cause severe damage to the RockShaft and/or Frame.
PAGE 3
Relocate the scraper mounting strap on the left hand wing for clearance on a P/N 171861 (new) center frame. 1. Using a grinder, cut off wheel or torch remove or trim strap flush with tube located at the 12 5/8” dimension  WARNING Failure to Trim the Strap flush will cause the Scraper Bar to bend. 2. Weld a new strap at the 16 5/8” dimension. See Figure 1-2. 3. Touch up the effected area with Brillion paint.
PAGE 4