Model 2410F Weatherproofer I Operator’s Manual LANDOLL CORPORATION 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.
Table of Contents 1 Introduction Understanding Safety Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 2 Standard Specifications 3 Assembly Instructions Weatherproofer I Frame Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Wheel Lift Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wheel Bearing Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6 Hydraulic Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7 Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7 Lubrication Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 1 Introduction The Landoll Model 2410F Weatherproofer I is a quality product designed to give years of trouble free performance. By following each section of this manual, your system will perform as designed for you and your operation CHAPTER 1 gives basic instructions on the use of this manual. CHAPTER 2 gives product specifications. These specifications supply lengths and measures for your equipment.
INTRODUCTION Understanding Safety Statements You will find various types of safety information on the following pages and on the machine signs (decals) attached to the machine. This section explains their meaning. The Safety Alert Symbol means ATTENTION! YOUR SAFETY IS INVOLVED! DANGER Danger means a life-threatening situation exists. Death can occur if safety measures or instructions on this label are not properly followed.
Chapter 2 Standard Specifications 2410F Series Weatherproofer I Model No. No. of Blades No. of Shank Transport F/R Shanks Spacing Width 2410F-7-24 2410F-9-24 18/20 22/24 7 9 24” 24” Transport Height 14’-8” 14’-8” 12’-1” 13’-7” Working Width 14’-0” 18’-0” Estimated Weight (Lbs.) 23,990 25,560 Tire Inflation Tire Size 380/55R 16.5 Imp (Used on 2410F-7-24 & 2410F-9-24) Tire Manufacturer Goodyear Ply/ Load Rating 8,000 lbs. @ 20 mph Inflation Pressure (Psi) (Max.
STANDARD SPECIFICATIONS LANDOLL CORPORATION GENERAL TORQUE SPECIFICATIONS (REV. 4/97) THIS CHART PROVIDES TIGHTENING TORQUES FOR GENERAL PURPOSE APPLICATIONS WHEN SPECIAL TORQUES ARE NOT SPECIFIED ON PROCESS OR DRAWING. ASSEMBLY TORQUES APPLY TO PLATED NUTS AND CAPSCREWS ASSEMBLED WITHOUT SUPPLEMENTAL LUBRICATION (AS RECEIVED CONDITION). THEY DO NOT APPLY IF SPECIAL GRAPHITE MOLY-DISULFIDE OR OTHER EXTREME PRESSURE LUBRICANTS ARE USED.
STANDARD SPECIFICATIONS LANDOLL CORPORATION HYDRAULIC FITTING TORQUE SPECIFICATIONS 37o JIC, ORS, & ORB (REV. 10/97) THIS CHART PROVIDES TIGHTENING TORQUES FOR HYDRAULIC FITTING APPLICATIONS WHEN SPECIAL TORQUES ARE NOT SPECIFIED ON PROCESS OR DRAWING. ASSEMBLY TORQUES APPLY TO PLATED CARBON STEEL AND STAINLESS STEEL FITTINGS ASSEMBLED WITHOUT SUPPLEMENTAL LUBRICATION (AS RECEIVED CONDITION). THEY DO NOT APPLY IF SPECIAL GRAPHITE MOLY-DISULFIDE OR OTHER EXTREME PRESSURE LUBRICANTS ARE USED.
STANDARD SPECIFICATIONS 6-3/8 2-3/8 2-3/8 4-3/8 4-3/8 10-3/8 10-3/8 2410f-7-24 shank placement Figure 2-1: Shank Placement Assembly (2410F-7-24) 2-4 F-735-0114 Edition
STANDARD SPECIFICATIONS 6-3/8 2-3/8 2-3/8 6-3/8 6-3/8 10-3/8 10-3/8 4-3/8 4-3/8 2410-9-24 shank placement Figure 2-2: Shank Placement Assembly (2410F-9-24) 2-5
STANDARD SPECIFICATIONS 10-1/4 6-7/8 13-3/4 3-3/4 10-13/16 10-13/16 27-5/8 2410F-7-24 7-1/2 29-1/4 6-7/8 9-1/8 7-1/16 29-1/4 24-5/16 combo w chopper reel placement 2410F-9-24 Figure 2-3: Finishing Combo w/ Chopper Reel Installation 2-6 F-735-0114 Edition
STANDARD SPECIFICATIONS 6-3/4 10-3/8 10-9/16 6-7/16 14 14 27-5/16 2410F-7-24 6-7/8 7-1/2 7-1/16 9-3/16 29-1/4 29-1/4 24-3/8 combo w conditioner reel placement 2410F-9-24 Figure 2-4: Finishing Combo w/ Conditioner Reel Installation 2-7
STANDARD SPECIFICATIONS 10-13/16 10-13/16 3-3/4 27-5/8 2410F-7-24 29-1/4 29-1/4 9-1/8 24-5/16 chopper reel placement 2410F-9-24 Figure 2-5: Finishing Chopper Reel Installation 2-8 F-735-0114 Edition
STANDARD SPECIFICATIONS 14 14 6-7/16 27-5/16 2410F-7-24 29-1/4 29-1/4 9-3/16 24-3/8 conditioner reel placement 2410F-9-24 Figure 2-6: Finishing Conditioner Reel Installation 2-9
STANDARD SPECIFICATIONS 11-7/16 7-1/8 11-15/16 2410F-7-24 7-11/16 harrow placement 6-9/16 7-1/8 2410F-9-24 Figure 2-7: Finishing Harrow Installation 2-10 F-735-0114 Edition
Chapter 3 Assembly Instructions It is very important that your new 2410F Weatherproofer I be properly assembled, adjusted and lubricated before use. Illustrations to assist with the assembly process are provided in “Standard Specifications” on page 2-1. They show proper shank and light mounting bracket spacing. Illustrations in this section show proper assembly procedures. Remove paint from grease fittings. Replace any grease fittings that are damaged or missing. Be sure to return screws, clips, etc.
ASSEMBLY INSTRUCTIONS REAR TOWER PLATE ASSEMBLY CLAMP ASSEMBLY MAIN FRAME ASSEMBLY WING STOP MOUNT ASSEMBLY FRONT TOWER PLATE ASSEMBLY m2410f-9-24 main frame assy op Figure 3-1: Frame Assembly 3-2 F-735-0114 Edition
ASSEMBLY INSTRUCTIONS Weatherproofer I Frame Assembly IMPORTANT Read all safety precautions at the front of the section before attempting any of the following procedures. 1. Place frame assembly on stands approximately 36” high. The assembly area should be a large level area of sufficient size to accommodate the Weatherproofer I when fully assembled (See Figure 3-1.) 2. The front and rear tower plate, wing stop mount, and clamp assemblies are installed at the factory.
ASSEMBLY INSTRUCTIONS 1-5/8 X 1-1/4 X 1 BUSHING 90 ADAPTER 4-1/2 X 16 HYDRAULIC CYLINDER 3/4-10 HEX LOCK NUT 3/4-10 X 2 HEX HEAD CAP SCREW WALKING BEAM SPINDLE LIFT BEARING CAP 2-1/2 THRUST WASHER 4” UHMW BEARING ROCKSHAFT 1-8 HEX LOCK NUT 3 X 2-1/2 X 4 SPRING BUSHING 3/4-10 HEX LOCK NUT 3/4-10 X 4-1/2 HEX HEAD CAP SCREW LIFT BEARING CAP 1/2-13 X 5 HEX HEAD CAP SCREW HUB AND SPINDLE ASSEMBLY WALKING BEAM ASSEMBLY 1/2-13 HEX LOCK NUT TIRE AND WHEEL ASSEMBLY 2410f-9-24 rockshaft assy op Figure
ASSEMBLY INSTRUCTIONS Wheel Lift Installation 1. Place 4” UHMW bearings onto rockshaft. Attach lift bearing caps onto rockshafts using 3/4-10 x 2 hex head cap screws and hex lock nuts. 2. Attach rockshaft to the frame assembly using lift bearing cap, 3/4-10 x 2 hex head cap screws, and hex lock nuts. 3. Attach base end of each 4-1/2 x 16 hydraulic cylinder to the main frame using lift pins and 5/16 x 2-1/2 spring slotted pins which are included with the cylinder (See Figure 3-2.
ASSEMBLY INSTRUCTIONS RH WING WELDMENT 1-3/4 THRUST WASHER 4 X 24 HYDRAULIC CYLINDER 5/16 X 2-1/2 SPRING SLOTTED PIN EXTENSION BACKER PLATE 1 X 7-5/16 PIN 1-1/4-7 HEX LOCK NUT LH WING WELDMENT 1W FLAT WASHER MAIN FRAME ASSEMBLY 90 ELBOW W/ 1/16 RESTRICTOR 1-3/4 X 7-3/4 PIN 3/8 X 3 SPRING SLOTTED PIN EXTENSION WELDMENT HINGE PIN 1/2 X 2-1/4 GROOVED ALLOY PIN 1 X 8-3/4 PIN 5/16 X 2 SPRING SLOTTED PIN 3/4-10 X 8 HEX HEAD CAP SCREW SHANK CLAMP BOLT CLAMP ASSEMBLY (2410F-9-24 MODEL ONLY) 1N FLAT WASHE
ASSEMBLY INSTRUCTIONS Weatherproofer I Wing and Extension Installation IMPORTANT Read all safety precautions at the front of the section before attempting any of the following procedures. WARNING Do not attempt to lift heavy parts (such as the frame, disc gangs, wheel lift, and pull hitch) manually. Use a hoist or a forklift to move these parts into position. 1.
ASSEMBLY INSTRUCTIONS LEVELER TUBE 1-1/4N FLAT WASHER HITCH PIN 1-8 HEX LOCK NUT 1/2 X 2-1/4 GROOVED ALLOY PIN 1-1/4 - 7 HEX NUT 1-1/4 - 7 X 8 HEX HEAD CAP SCREW GR8 1-1/4 SPLIT LOCK WASHER LEVELER TOWER 1-1/4 - 7 HEX NUT HITCH RADIUS ROD ASSEMBLY 1-1/4 SPLIT LOCK WASHER FRAME ASSEMBLY 1/4-20 X 1 HEX HEAD CAP SCREW WING NUT CLAMP 3/4-10 FLANGE NUT 3/8-16 HEX NUT 3/8-16 X 3-1/2 ALL THREAD SCREW 1/4-20 HEX LOCK NUT 1-8 X 7-1/2 HEX HEAD CAP SCREW HITCH CLEVIS JACK 1-1/4-7 X 9-1/2 HEX HEAD CAP SCR
ASSEMBLY INSTRUCTIONS Hitch Installation IMPORTANT 1. Attach the hitch weldment to the front of the frame using hitch pins, 1-8 hex lock nuts, and 1/2 x 2-1/4 grooved alloy pins (See Figure 3-4.) The leveler tower must be installed so that the narrow end of the tower is down and the reinforced holes are to the rear of the machine. 2. Move the jack to the forward mounting tube and rotate to parking position to support the front of the hitch. 7.
ASSEMBLY INSTRUCTIONS DEPTH STOP TUBE ASSEMBLY DEPTH STOP HANDLE FRAME ASSEMBLY 5/8-11 HEX LOCK NUT DEPTH STOP MOUNT PLATE 5/8-11 X 2-1/2 HEX HEAD CAP SCREW WHEEL AND LIFT ASSEMBLY 3/8-16 HEX LOCK NUT 3/8-16 X 1-1/4 HEX HEAD CAP SCREW 2410f-9-24 depth stop tube assy op Figure 3-5: Depth Stop Assembly Installation 3-10 F-735-0114 Edition
ASSEMBLY INSTRUCTIONS Depth Stop Tube Assembly 1. Attach the depth stop mount plate to the lift using 3/8-16 x 1-1/4 hex head cap screws and hex lock nuts. IMPORTANT It may be necessary to leave these screws loose to attach the valve hoses later. 2. Lay the depth stop tube assembly on top of the center frame. Insert a 5/8-11 x 2-1/2 hex head cap screw in the rear hole of the tube assembly from the left side (See Figure 3-5.
ASSEMBLY INSTRUCTIONS 3/4-10 X 11 HEX HEAD CAP SCREW GR5 FRAME ASSEMBLY RIGHT REAR DISC GANG ASSEMBLY 3/4 FLAT WASHER RIGHT FRONT DISC GANG ASSEMBLY 3/4-10 X 2 HEX HEAD CAP SCREW GR8 FOUR BOLT PLATE 3/4-10 X 11 HEX HEAD CAP SCREW GR8 SLOTTED CLAMP PLATE LEFT FRONT DISC GANG ASSEMBLY LEFT REAR DISC GANG ASSEMBLY 3/4-10 HEX LOCK NUT 2410f-7-24 disc gang inst Figure 3-6: Disc Gang Installation - Wing Frame (2410F-7-24) 3-12 F-735-0114 Edition
ASSEMBLY INSTRUCTIONS FRAME ASSEMBLY RIGHT REAR DISC GANG ASSEMBLY 3/4-10 X 11 HEX HEAD CAP SCREW GR5 RIGHT FRONT DISC GANG ASSEMBLY 3/4 FLAT WASHER 3/4-10 X 2 HEX HEAD CAP SCREW GR8 3/4-10 X 2-1/4 HEX HEAD CAP SCREW GR8 SLOTTED CLAMP PLATE FOUR BOLT PLATE 3/4-10 X 11 HEX HEAD CAP SCREW GR8 LEFT REAR DISC GANG ASSEMBLY 3/4-10 HEX LOCK NUT LEFT FRONT DISC GANG ASSEMBLY 2410f-9-24 disc gang inst Figure 3-7: Disc Gang Installation - Wing Frame (2410F-9-24) Disc Gang Installation - Wing Frame DANGE
ASSEMBLY INSTRUCTIONS CLAMP ASSEMBLY 3/4-10 HEX LOCK NUT 5/8-11 HEX LOCK NUT 3/4-10 X 4 HEX HEAD CAP SCREW 5/8-11 X 3-3/4 HEX HEAD CAP SCREW 1-1/4 X 4 BOLT-IN SHANK 5/8 X 3/4 X 1-1/4 CONNEX BUSHING 1-1/4” SHARK FIN POINT 1-1/4” WINGED SUBSOILER POINT 3/8 X 2 SPRING SLOTTED PIN 1-1/4” SHANK V-CAP POINT 2410 shank inst op Figure 3-8: Auto Reset Shank and Point Installation 3-14 F-735-0114 Edition
ASSEMBLY INSTRUCTIONS Auto Reset Shank and Point Installation 1. Attach each 1-1/4 x 4 bolt-in shank to each clamp assembly using 3/4-10 x 4 hex head cap screw and hex lock nut in the top hole and 5/8-11 x 3-3/4 hex head cap screw, 5/8 x 3/4 x 1-1/4 connex bushing, and hex lock nut in the second hole (See Figure 3-8.) 2. Connect subsoiler points to each shank using 3/8 x 2 spring slotted pins.
ASSEMBLY INSTRUCTIONS 3/8 X 112 HOSE ASSEMBLY SEE DETAIL A 1/2 X 94 HOSE ASSEMBLY SEE DETAIL B 1/2 X 271 HOSE ASSEMBLY SEE DETAIL C 16 PORT HYDRAULIC MANIFOLD ASSEMBLY 1/2 X 204 HOSE ASSEMBLY 90 ADAPTER 1” X 8” BLUE HOSE WRAP 90 ADAPTER CONNECTS TO LIFT CYLINDER BASE END 1/2 X 94 HOSE ASSEMBLY 3/4-16 MALE COUPLER CONNECTS TO LIMIT VALVE SIDE PORT CONNECTS TO LIFT CYLINDER ROD END 1/2 X 271 HOSE ASSEMBLY DETAIL A CONNECTS TO TRACTOR 90 ADAPTER LIMIT VALVE ADAPTER 1/2 X 94 HOSE ASSEMBLY 90 ADAP
ASSEMBLY INSTRUCTIONS 4 X 24 HYDRAULIC CYLINDER 3/8 X 27 HOSE ASSEMBLY CONNECTS TO REAR FOLD CYLINDER BASE ENDS CONNECTS TO REAR FOLD CYLINDER ROD END CONNECTS TO REAR FOLD CYLINDER ROD END 3/8 X 31 HOSE ASSEMBLY 3/8 X 31 HOSE ASSEMBLY SEE DETAIL A 90 ADAPTER CONNECTS TO MIDDLE MANIFOLD REAR PORTS 16 PORT MANIFOLD SEE DETAIL B DETAIL A 3/8 X 196 HOSE ASSEMBLY 4 X 24 HYDRAULIC CYLINDER CONNECTS LOCK CYLINDER ROD END W/ UPPER RH PORT CONNECTS LOCK CYLINDER BASE END W/ 2ND UPPER RH PORT 3/8 X 27
ASSEMBLY INSTRUCTIONS CONNECTS TO LH FOLD CYLINDER BASE END CONNECTS TO RH FOLD CYLINDER BASE END 3/8 X 48 HOSE ASSEMBLY 3/8 X 105 HOSE ASSEMBLY 3/8 X 31 HOSE ASSEMBLY 3/8 X 50 HOSE ASSEMBLY 3/8 X 40 HOSE ASSEMBLY CONNECTS TO LH FOLD CYLINDER ROD END CONNECTS TO RH FOLD CYLINDER ROD END DETAIL C 2410f fold hyd p2 op Figure 3-11: Hydraulic Fold Manifold Detail C 3/8-16 X 3 OR 3/8-16 X 4 HEX HEAD CAP SCREW HOSE CLAMPS 3/8-16 HEX LOCK NUT 2410f hitch hose clamps Figure 3-12: Hitch Hose Clamps and
ASSEMBLY INSTRUCTIONS Hydraulic Installation NOTES Refer to Figure 3-9 for hydraulic lift diagram. Refer to Figures 3-10 and 3-11 for hydraulic fold diagrams. 1. Install a 16 port manifold to the front side of the manifold mount bracket at the center frame using 1/2-13 x 3-1/2 hex head cap screws and hex lock nuts. 2. Install a 16 port manifold on the front side of the rear inner tower plate using1/2-13 x 3-1/2 hex head cap screws and hex lock nuts. 7.
ASSEMBLY INSTRUCTIONS FOLD TOWER REAR PLATE SMV EMBLEM 1/4-20 X 1 HEX HEAD CAP SCREW 1/4-20 HEX LOCK NUT LH LIGHT BAR ASSEMBLY 1/4-20 X 1-1/4 HEX HEAD CAP SCREW AG RED LED SINGLE LAMP 1/2-13 HEX LOCK NUT REAR WARNING LIGHT HARNESS AG FLASHER CONTROL MODULE 1/2-13 X 3-3/4 HEX HEAD CAP SCREW 34” EXTENSION HARNESS RH LIGHT BAR ASSEMBLY MAIN WARNING LIGHT HARNESS 1/4-20 X 1 HEX HEAD CAP SCREW LIGHT BAR PLATE AG AMBER LED SINGLE LAMP 1/4-20 X 1-1/4 HEX HEAD CAP SCREW STOR-AWAY HARNESS 1/4-20 HEX LOCK NU
ASSEMBLY INSTRUCTIONS NOTE: IF REPAIRING OR REPLACING THE 7 PIN CONNECTOR, MATCH THE LETTERS AT THE BACK OF THE HARNESS TO THE 7 PIN CONNECTOR AS SHOWN. THE COLOR OF THE WIRE JACKET DOES NOT NECESSARILY MATCH THE COLOR MARKING OF THE 7 PIN CONNECTOR. #1 WHITE #2 BLACK #3 YELLOW #7 BLUE WIRING CHART 7-PIN CONNECTION 4-PIN CONNECTION GRND. 1 D YEL. 3 B GRN. 5 A BRN.
ASSEMBLY INSTRUCTIONS HOSE ASSEMBLY 1/4 X 54 2-1/2 X 2-1/2 CYLINDER ADAPTER, 90 HOSE ASSEMBLY 1/4 X 68 (S) ADAPTER, 45 ADAPTER (T) 8 PORT HYDRAULIC MANIFOLD ADAPTER, 90 HOSE ASSEMBLY 1/4 X 68 (Q) (W) HOSE ASSEMBLY 1/4 X 54 (R) (X) HOSE ASSEMBLY 3/8 X 86 ADAPTER (H) (L-1) 16 PORT HYDRAULIC MANIFOLD W/ 1/2-13 X 3-1/2 HEX HEAD CAP SCREW AND HEX LOCK NUT (G) HOSE ASSEMBLY 1/4 X 98 (K-1) HOSE ASSEMBLY 1/4 X 80 ADAPTER, 90 ADAPTER TEE (K-2) (C) HOSE ASSEMBLY 1/4 X 98 (L-2) (O) (D) (P) 3/8
ASSEMBLY INSTRUCTIONS (Q) (R) (S) (U) (T) (V) FRONT OF MACHINE 2-1/2 - 8-1/2 HOSE CLAMP (W) (X) HOSE CLAMP LEFT MANIFOLD (I) (E) (F) (J) (G) (K-1) (A) (B) (C) (D) (H) FRONT OF MACHINE (K-2) (L-1) (L-2) (M) (N) (O) (P) 3/8-16 X 4 HEX HEAD CAP SCREW CENTER MANIFOLD (REAR) HOSE CLAMP FRONT OF MACHINE (AA) (AC) (AB) (AD) (AE) (AF) 3/8-16 FLANGE LOCK (Z) (Y) RIGHT MANIFOLD 1/2-13 X 4 RD HEAD SQ NECK SCREW TINE RETAINER BUSHING HARROW ADJUSTMENT PLATE WRENCH QUICK HITCH PIN WRENCH COMBO MO
ASSEMBLY INSTRUCTIONS REAR FOLD TOWER ASSEMBLY 16 PORT HYDRAULIC MANIFOLD 22 NOTE: SIDE PLATE HIDDEN FOR CLARITY.
ASSEMBLY INSTRUCTIONS Finishing Combo w/ Chopper Reel Installation (Option) 3. Install fittings into manifold according to Figures 3-15 thru 3-16. 4. Install hoses per Figures 3-15 thru 3-16. 5. Install steel plugs in any remaining open manifold or valve ports. NOTES Refer to Figure 3-15 for hydraulic diagram. See Figure 2-3 for finishing combo w/ chopper reel placement dimensions. 1.
ASSEMBLY INSTRUCTIONS REAR FOLD TOWER ASSEMBLY 16 PORT HYDRAULIC MANIFOLD 22 NOTE: SIDE PLATE HIDDEN FOR CLARITY.
ASSEMBLY INSTRUCTIONS Finishing Combo w/ Conditioner Reel Installation (Option) NOTES Refer to Figure 3-15 for hydraulic diagram. See Figure 2-4 for finishing combo w/ conditioner reel placement dimensions. 1. Attach two combo attachment harrow arms to rear of frame using 1-8 x 7-1/2 hex head cap screws and hex lock nuts (See Figure 3-19.) 2. Install the manifold to the manifold bracket on the rear of frame using 1/2-13 x 3-1/2 hex head cap screws and hex lock nuts. 3.
ASSEMBLY INSTRUCTIONS HOSE ASSEMBLY 1/4 X 34 2-1/2 X 2-1/2 CYLINDER ADAPTER, 90 HOSE ASSEMBLY 1/4 X 40 ADAPTER, 45 (S) ADAPTER (T) 8 PORT HYDRAULIC MANIFOLD ADAPTER, 90 HOSE ASSEMBLY 1/4 X 40 HOSE ASSEMBLY 1/4 X 34 (Q) (W) (R) (X) HOSE ASSEMBLY 3/8 X 86 ADAPTER (L-1) (H) 16 PORT HYDRAULIC MANIFOLD W/ 1/2-13 X 3-1/2 HEX HEAD CAP SCREW AND HEX LOCK NUT (G) HOSE ASSEMBLY 1/4 X 72 (K-1) HOSE ASSEMBLY 1/4 X 54 ADAPTER, 90 ADAPTER TEE (K-2) HOSE ASSEMBLY 1/4 X 72 (L-2) (C) (O) 3/8 X 428 HOSE
ASSEMBLY INSTRUCTIONS (Q) (R) (S) (U) (T) (V) FRONT OF MACHINE (W) (X) LEFT MANIFOLD (I) (E) (F) (J) (G) (K-1) (A) (B) (C) (D) (H) FRONT OF MACHINE (K-2) (L-1) (L-2) (M) (N) (O) (P) CENTER MANIFOLD (REAR) FRONT OF MACHINE (AA) (AC) (AB) (AD) (AE) (AF) (Z) (Y) RIGHT MANIFOLD 3/8-16 X 1-3/4 RD HEAD SQ NECK SCREW HOSE CLAMP m179167 op p2 3/8-16 FLANGE LOCK Figure 3-22: Finishing Reel Hydraulic Manifold and Miscellaneous Details 3-29
ASSEMBLY INSTRUCTIONS REAR FOLD TOWER ASSEMBLY 16 PORT HYDRAULIC MANIFOLD 22 NOTE: SIDE PLATE HIDDEN FOR CLARITY.
ASSEMBLY INSTRUCTIONS Finishing Chopper Reel Installation (Option) NOTES Refer to Figure 3-21 for hydraulic diagram. See Figure 2-5 for finishing chopper reel placement dimensions. 1. Attach reel arm assemblies to rear frame in second hole from top using 1-8 x 7-1/2 hex head cap screw, 5” pivot bushing, and hex lock nut (See Figure 3-23.) 2. Attach reel arms w/ extension assemblies to rear frame using 1-8 x 7-1/2 hex head cap screws and hex lock nuts. 3.
ASSEMBLY INSTRUCTIONS REAR FOLD TOWER ASSEMBLY 16 PORT HYDRAULIC MANIFOLD 22 1/2-13 X 3-1/2 HEX HEAD CAP SCREW AND HEX LOCK NUT NOTE: SIDE PLATE HIDDEN FOR CLARITY.
ASSEMBLY INSTRUCTIONS Finishing Conditioner Reel Installation (Option) NOTES Refer to Figure 3-21 for hydraulic diagram. See Figure 2-6 for finishing conditioner reel placement dimensions. 1. Attach reel arm assemblies to rear frame in second hole from top using 1-8 x 7-1/2 hex head cap screw, 5” pivot bushing, and hex lock nut (See Figure 3-24.) 2. Attach reel arms w/ extension assemblies to rear frame using 1-8 x 7-1/2 hex head cap screws and hex lock nuts. 3.
ASSEMBLY INSTRUCTIONS 1-8 HEX NUT SPRING ASSEMBLY 22 1 X 9 SPRING ADJUSTMENT BOLT 7-1/4 ADJUSTMENT PIN W/ SNAP RING 1-8 X 7-1/2 HEX HEAD CAP SCREW HARROW ARM ASSEMBLY 4-1/4” PIVOT BUSHING 1-8 HEX LOCK NUT HARROW ASSEMBLY 5/8-11 FLANGE HEAD SERRATED NUT 1-8 X 9 SPRING ADJUSTMENT BOLT HARROW STIFFENER PLATE 2-1/2 SNAP RING SPRING CLAMP U-BOLT 7-1/4 ADJUSTMENT PIN 1” SPLIT LOCK WASHER 1-8 HEX LOCK NUT 17” SPRING ASSEMBLY 5/8-11 X 5 HEX HEAD CAP SCREW 2410-9-24_ harrow inst Figure 3-25: Finishing H
ASSEMBLY INSTRUCTIONS Finishing Harrow Installation (Option) 3. Attach 17” spring assembly to adjustment pin using 1-8 x 9 hex head cap screw, split lock washer, and hex lock nuts. See Figure 2-7 for 3 Row Coil Tine Harrow placement dimensions. 4. Attach harrow stiffener plate to top of harrow arm using 5/8-11 x 5 hex head cap screw and flange head serrated nut. 1. Attach harrow arms to rear of frame in top hole using 1-8 x 7-1/2 hex head cap screws and hex lock nuts (See Figure 3-25.) 2.
ASSEMBLY INSTRUCTIONS Final Assembly 1. Attach a tractor to the implement and charge the lift system hydraulics as described in “Hydraulic Lift System” on page 4-3. 4 FOOT 2. Install the 1-1/2 x 16 lockouts on both 3-1/2 x 16 cylinders on the frame. 300 POUNDS PULL 3. Connect lights to the tractor and verify operation. 4. Check tires for proper inflation. 5. Level the Weatherproofer I from front to rear as described in “Leveling (Front-to-Rear)” on page 4-4. 6.
ASSEMBLY INSTRUCTIONS Notes: 3-37
ASSEMBLY INSTRUCTIONS 3-38 F-735-0114 Edition
Chapter 4 Operation and Maintenance DANGER Never allow anyone to ride on the 2410F Weatherproofer I at any time. Allowing a person to ride on the machine can inflict serious personal injury or death to that person. DANGER Disc blades are extremely sharp. Exercise extreme care when working on or near disc blades. Do not allow discs to roll over or fall onto any bodily part. Do not allow wrenches to slip when working near disc blades. Never push wrenches toward disc blades.
OPERATION AND MAINTENANCE Tractor Preparation The Landoll 2410F Weatherproofer I is designed to be pulled by tractor equipped with a double lip or clevis type hitch. If your tractor is not equipped as such, you need to purchase the hitch from your local tractor dealer. If your Weatherproofer is equipped with the clevis option, this should be removed. The clevis option is only for transport use. Before attaching the Weatherproofer, prepare the tractor as follows: 1.
OPERATION AND MAINTENANCE Hydraulic Lift System 1-1/2 X 16 LOCKOUT The Weatherproofer I is equipped with a hydraulic lift system to raise and lower the unit in the field. 1/8 HAIRPIN WARNING Escaping hydraulic fluid can cause serious personnel injury. Relieve system pressure before repairing, adjusting, or disconnecting. Wear proper hand and eye protection when searching for leaks. Use cardboard instead of hands (See Figure 4-2.) Keep all components (cylinders, hoses, fittings, etc.
OPERATION AND MAINTENANCE General Operation Leveling (Front-to-Rear) 1. The horsepower requirements are typically 40-50 horsepower per shank. This will vary widely due to speed, depth, moisture, residue and types of soils. Local dealers can help in making recommendations for your areas. 2. Operating speed is typically 4.5-6 mph. Excessive speed can cause the unit to bounce, uneven depth, and create undesirable ridges. 3.
OPERATION AND MAINTENANCE Disc Blades Depth Stop Adjustment (Manual) 1. The 2410F Weatherproofer I is equipped with 24" or 26” disc blades. 2. The 24” diameter blades are concave with a thickness of 4 ga (.256”) and are standard for the 2410F Weatherproofer I. 3. Sharpening – In some cases there is a desire to sharpen disc blades for improved cutting. There are several people who roll-sharpen disc blades. Most disc blades used today are made of chrome-boron steel.
OPERATION AND MAINTENANCE 2-1/4” SPINDLE TRIPLE LIP GREASE SEAL INNER BEARING CONE INNER BEARING CUP 8 BOLT HUB OUTER BEARING CUP OUTER BEARING CONE SPINDLE WASHER 1-14 HEX SLOT NUT 3/16 X 1-1/2 COTTER PIN HUB CAP 2410 wheel bearing maintenance Figure 4-8: Wheel Bearing Maintenance Wheel Bearing Maintenance Wheel bearing maintenance should be performed at the beginning of every season of use. Check the wheel bearings periodically for excessive end play.
OPERATION AND MAINTENANCE Hydraulic Maintenance Transport 1. Check the tractor hydraulic fluid level per tractor owners manual and after any leakage. Check fluid level with the cylinders in the retracted position. 2. If a cylinder or valve leaks, disassemble the parts to determine the cause of the leak. Any time a cylinder is opened up, or whenever any seal replacement is necessary, it is advisable to clean all parts and replace all seals. Seal kits are available from your Landoll dealer. 3.
OPERATION AND MAINTENANCE 4. Check that tires are of proper size, load rating, and inflated to manufacture specifications before transporting. Check wheel lug bolts to insure tightness. 1-1/2 X 16 LOCKOUT 1/8 HAIRPIN 5. Know the transport heights and widths of the unit before transporting. Attachments can increase the transport dimensions of the implement. Use caution when transporting near bridges and power lines. WARNING Electrocution can occur without direct contact. 6.
OPERATION AND MAINTENANCE 5 6 2 4 3 1 2410f lube Figure 4-11: Lubrication Schedule LUBRICATION TABLE ITEM DESCRIPTION INTERVAL (Hours Unless Stated) NO.
OPERATION AND MAINTENANCE Lubrication Maintenance Storage 1. Table 4-1 specifies the lubrication points and intervals on the 2410F Weatherproofer I. Proper maintenance of your machine will, under normal operating conditions, help to keep it operating at or near its peak performance for an extended period of time. Proper maintenance is also a condition of keeping your warranty in good status (See Figure 4-11.) 2.
OPERATION AND MAINTENANCE Notes: 4-11
OPERATION AND MAINTENANCE Page Intentionally Blank 4-12 F-735-0114 Edition
Chapter 5 Troubleshooting Guide The Troubleshooting Guide, shown below, is included to help you quickly locate problems that can happen using your 2410F Weatherproofer I. Follow all safety precautions stated in the previous sections when making any adjustments to your machine. PROBLEM UNEVEN DEPTH PROBABLE CAUSE SOLUTION Unit not level when under power in the field Level unit front to rear (See “Leveling (Front-to-Rear)” on page 4-4.) Excessive disc gang depth or down pressure Reduce machine depth.
TROUBLESHOOTING GUIDE Notes: 5-2 F-735-0114 Edition
Equipment from Landoll Corporation is built to exacting standards ensured by ISO 9001:2008 registration at all Landoll manufacturing facilities. Model 2410F Weatherproofer I Operator’s Manual Re-Order Part Number F-735-0114 LANDOLL CORPORATION 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM Copyright 2010.