OPERATOR’S MANUAL REPAIR PARTS CATALOG Subsoil Chisel Plow with ONE & TWO SHANKS MODELS: SCP-1 SCP-2 IMPORTANT! Repairs cannot be purchased retail direct from factory. Order through your Brillion dealer. BRILLION FARM EQUIPMENT 1298rev2-10-04 1298rev401 BRILLION, WISCONSIN 54110 www.brillionfarmeq.
1298rev401 6K007
SUBSOIL CHISEL PLOW ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ SCP-1 & SCP-2 CONTENTS Introduction ..................................................................................................................................... 3 Location Reference ................................................................................................................ 3 Parts Ordering ...............................................................
1298rev401 6K007
Introduction Your Brillion Sub-soil Chisel Plow is built with the best materials and workmanship available. It has been designed to give years of trouble-free operation. Proper care and operation will insure that you receive the service and long life built into this machine. Study this manual carefully before attempting to operate the machine. If items in the manual are not understood, contact your local Brillion dealer.
SAFETY SUGGESTIONS Investigation has shown that nearly one-third of all farm accidents are caused by careless use of machinery. You can do your part in improving safety by observing the following suggestions. Insist that all people working with you or for you abide by them. 1. Never turn corners at a high rate of speed. 2. Never work under the chisel plow unless it is securely blocked up and cannot be knocked off the blocks. 3.
DECAL LOCATIONS Figure 2B 1. 8J310 - Decal, “Caution” list 2.
SET-UP INSTRUCTIONS Your Brillion Subsoil Chisel Plow is shipped to you in separate assemblies. Before assembling the unit, separate the various bundles and open the box assembly, taking care not to lose any of the parts or hardware. (Refer to repair parts section for relative location of parts.) Block up the frame or mount it to the three point hitch on the tractor for the assembly of shanks.
SUPPORT STANDS Assemble the support stands through the vertical tubes on the ends of the frame. Insert the 1/4 x 2 1/4" long cotter pins in the top holes of the support stands to prevent them from falling out when the machine is raised. When the machine is idle and not mounted to the tractor, the 1/2 x 3" long clevis pins, inserted in the middle holes, will prevent the unit from tipping.
MACHINE SPECIFICATIONS Shanks: 1" thick, high strength ductile iron Overall Width: 1-Shank Machine = 29” 2-Shank Machine = 50 1/2” Working Depth: 0 to 16" Hitch: Pins provided are designed to work with Category II three-point hitch on 2-Shank Machine and Category I Three-Point Hitch on 1-Shank Machine.
REPAIR PARTS ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ CONTENTS 1-Shank Frame Assembly ....................................................................................................... 10 2-Shank Frame Assembly ....................................................................................................... 12 Shank Assembly ................................................................................................................
1 9 14 13 8 7 12 ! ! 2, 4 10 CAUTION 3, 5 1. 2. 3. 4. 8 5. 6. 7. 8. 15 9. DO NOT LUBRICATE, ADJUST OR REPAIR WHEN MACHINE IS IN MOTION. DO NOT TOW OR TRANSPORT FASTER THAN 15 MILES PER HOUR. DO NOT RIDE OR ALLOW OTHERS TO RIDE ON THE MACHINE. BLOCK UP ALL HYDRAULICALLY OR MECHANICALLY RAISED COMPONENTS TO PREVENT UNINTENDED LOWERING, OR LOWER THE MACHINE TO THE GROUND TO MAKE ADJUSTMENT OR REPAIRS WHEN NOT IN USE. KEEP ALL PERSONS AWAY FROM MACHINE DURING HITCHING AND OPERATING.
“1”-SHANK FRAME ASSEMBLY Index No. Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 6K009 5K990 6D758 6C729 8D423 5C461 --1J722 6K010 2J430 8J310 9D047 6D049 3C335 6C400 8K829 1298rev401 2-10-04 No. Req’d Description “1” -Shank Frame Assembly, complete (w/out shank) “1” -Shank Frame Bolt, 3/4-10 NC x 3 1/2” Long Gr. 5 Locknut, 3/4-10 NC Bolt, 5/8-11 NC x 3 3/4” Long Gr. 5 Locknut, 5/8-11 NC ------Klik-Pin, 7/16” Hitch Pin w/ Nut Decal, Reflective Red Decal, Caution List Support Stand Cotter Pin, 1/4” dia.
CAUTION DEEP TILL OPERATION CAN DAMAGE UNDERGROUND UTILITIES CAUSING DANGEROUS CONDITIONS AND DISRUPTING SERVICES. DETERMINE THE DEPTH AND LOCATION OF BURIED CABLES, PIPE LINES, AND DRAIN TILES BEFORE OPERATION. 8K829 20 21 19 7 1 17 12 9 9 8 16 20 19 10 2, 4 3, 5 15 13, 14 7 3, 5 8 18 18 2, 4 10 11 CAUTION 1. 2. 3. 4. 5. 6. 7. 8. 9. 1298rev401 2-10-04 DO NOT LUBRICATE, ADJUST OR REPAIR WHEN MACHINE IS IN MOTION. DO NOT TOW OR TRANSPORT FASTER THAN 15 MILES PER HOUR.
“2”-SHANK FRAME ASSEMBLY Index No. Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 6K006 5K997 6D758 6C729 8D423 5C461 --5D110 5D156 2J430 8J310 9D047 6D049 3C335 6C400 6K003 6K004 6K005 8D042 1C211 1C210 8K829 1298rev401 2-10-04 No. Req’d Description “2” -Shank Frame Assembly, complete (w/out shank) “2” -Shank Frame Bolt, 3/4-10 NC x 3 1/2” Long Gr. 5 Locknut, 3/4-10 NC Bolt, 5/8-11 NC x 3 3/4” Long Gr.
11 18 18 17 17 12 9 10 14 5 16 2 13 16 15 7 6 3 1 4 8 1298rev401 Page 14 6K007
SHANK ASSEMBLY Index No. Part No. No. Req’d Description SNGL 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1298rev401 1J480 1J479 1J484 1J485 1J481 1J486 1C120 5C392 1C659 6K003 6K004 6K005 6D758 6C729 8D423 5C461 8D042 1C211 1C210 Shank Assembly, complete (Incl. Items 1-8) Shank only Clamp Wearstrip Point Capscrew, 1/2-13 NC x 2 1/4” Long Gr. 5 Flat Washer, 1/2” Lock Nut, 1/2-13 NC Roll Pin, 1/4” x 1 1/2” Long L. H. Angle R. H Angle Plate Bolt, 3/4-10 NC x 3 1/2” Long Gr.
INDEX Part No. Index No. Page No. Part No. 13 11 13 11 13 13 11 9 9 13 11 13 11 9 11 13 9 5K990 5K997 6K003 6K003 6K004 6K004 6K005 6K006 6K009 6K010 6K005 8K829 8K829 1C211 1C659 3C335 5C077 5C392 5C461 6C400 6C400 6C729 6C729 6C729 6 20 18 19 17 8 13 13 6 7 5 15 14 14 3 13 3 Page No. Part No. Index No. Page No. K C 1C120 1C210 Index No.
Equipment from Landoll Corporation is built to exacting standards ensured by ISO 9001:2008 registration at all Landoll manufacturing facilities. LANDOLL CORPORATION 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM Copyright 2010.
