Laney DB SERIES USER MANUAL MODEL : DB150C DB150H DB300C DB300H DB400C DB400H
Laney 1 INTRODUCTION Congratulations on your decision to purchase a Laney amplifier. Laney products are designed with ease of operation as a primary objective, however to ensure you derive the best from your new amplifier, it is important you take time to read this user manual and to familiarise yourself with the control functions and facilities available BEFORE SWITCHING ON After unpacking your amplifier check that it is factory fitted with a three pin 'grounded' (or earthed) plug.
Laney 2 FRONT PANEL FEATURES DB150C & DB150H 15 14 16 TREBLE FET GAIN LEVEL LO OK 3 HI 5 4 6 2 7 2 8 1 0 10 4 3 5 5 3 4 5 6 PASSIVE 8 1 1 PRE 2 4 5 6 2 7 2 MID 8 1 9 10 0 INPUT 3 7 FET TUBE 2 HI 0 0 10 8 9 0 EQ 10 1 DB150C 0 NOISE LIMIT GATE 4 5 5 PRESHAPE BASS 5 6 4 3 7 1 3 POWER 6 2 2 4 TUBE POST 0 1 -0+ 1 3 9 5 3 4 PREAMPS ACTIVE VOLUME 2 4 9 GRAPHIC EQ 1 -0+ 1 3 40Hz 80Hz 160Hz320Hz 650Hz 1k3Hz2k6Hz 5kHz 10kHz
Laney 3 FRONT PANEL FEATURES DB150C & DB150H 15 14 16 TREBLE FET GAIN LEVEL LO OK 3 HI 5 4 6 2 7 2 8 1 0 10 4 3 5 5 3 4 5 6 PASSIVE 8 1 1 PRE 2 4 5 6 2 7 2 MID 8 1 9 10 0 INPUT 3 7 FET TUBE 2 HI 0 0 10 8 9 0 EQ 10 1 DB150C 0 NOISE LIMIT GATE 4 5 5 PRESHAPE BASS 5 6 4 3 7 1 3 POWER 6 2 2 4 TUBE POST 0 1 -0+ 1 3 9 5 3 4 PREAMPS ACTIVE VOLUME 2 4 9 GRAPHIC EQ 1 -0+ 1 3 40Hz 80Hz 160Hz320Hz 650Hz 1k3Hz2k6Hz 5kHz 10kHz
Laney 4 REAR PANEL FEATURES DB150C & DB150H 23 24 WARNING THIS EQUIPMENT MUST BE EARTHED. MAXIMUIM POWER CONSUMPTION 300 WATTS ~50 - 60 Hz. SPEAKER OUTPUT HORN 8P-86 CE SUPPLY VOLTAGE ~230V & FUSE RATING ~115V OFF T1A T2A PIN -1 = GND. PIN +1 = SIG. A TOTAL LOAD OF NO LESS THAN 8 OHMS CAN BE CONNECTED AT ANY ONE TIME. CAUTION TO REDUCE THE RISK OF FIRE HAZARD REPLACE FUSE WITH SAME TYPE AND RATING ONLY. ATTENTION REMPLACER LE FUSIBLE SERIAL No: PREAMP OUT PAR LE MEME ET LE CALIBRE.
Laney 5 REAR PANEL FEATURES DB150C & DB150H 23 24 WARNING THIS EQUIPMENT MUST BE EARTHED. MAXIMUIM POWER CONSUMPTION 300 WATTS ~50 - 60 Hz. SPEAKER OUTPUT HORN 8P-86 CE SUPPLY VOLTAGE ~230V & FUSE RATING ~115V OFF T1A T2A PIN -1 = GND. PIN +1 = SIG. A TOTAL LOAD OF NO LESS THAN 8 OHMS CAN BE CONNECTED AT ANY ONE TIME. CAUTION TO REDUCE THE RISK OF FIRE HAZARD REPLACE FUSE WITH SAME TYPE AND RATING ONLY. ATTENTION REMPLACER LE FUSIBLE SERIAL No: PREAMP OUT PAR LE MEME ET LE CALIBRE.
Laney 6 REAR PANEL FEATURES DB150C & DB150H 23 24 WARNING THIS EQUIPMENT MUST BE EARTHED. MAXIMUIM POWER CONSUMPTION 300 WATTS ~50 - 60 Hz. SPEAKER OUTPUT HORN 8P-86 CE SUPPLY VOLTAGE ~230V & FUSE RATING ~115V OFF T1A T2A PIN -1 = GND. PIN +1 = SIG. A TOTAL LOAD OF NO LESS THAN 8 OHMS CAN BE CONNECTED AT ANY ONE TIME. CAUTION TO REDUCE THE RISK OF FIRE HAZARD REPLACE FUSE WITH SAME TYPE AND RATING ONLY. ATTENTION REMPLACER LE FUSIBLE SERIAL No: PREAMP OUT PAR LE MEME ET LE CALIBRE.
BLT Industries Ltd., Newlyn Road, Cradley Heath, West Midlands. B64 6BE. Tel: (0044) (0)1384 633821 Fax: (0044) (0)1384 639186 Http://www.laney.co.uk In the interest of continued product development BLT Industries Ltd. Reserves the right to amend product specification wihtout prior notification.
