AH100 USER MANUAL
IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electric products, basic cautions should always be followed, including the following. 1. Read all safety and operating instructions before using this product 2. The product should be powered by a three pin `grounded (or earthed) plug connected to a power socket with a grounded earth outlet. 3. All safety and operating instructions should be retained for future reference 4. Obey all cautions in the Operating instructions and on the back of the unit 5.
Page 3 /12
Laney OPERATING INSTRUCTIONS BEFORE SWITCHING ON After unpacking your amplifier check that it is factory fitted with a three pin 'grounded' (or earthed) plug. Before plugging into the power supply ensure you are connecting to a grounded earth outlet. If you should wish to change the factory fitted plug yourself, ensure that the wiring convention applicable to the country where the amplifier is to be used is strictly conformed to.
Laney OPERATING INSTRUCTIONS Dear Player, Thank you very much for purchasing your new Laney product and becoming part of the worldwide Laney family. Each and every Laney unit is designed and built with the utmost attention to care and detail, so I trust yours will give you many years of enjoyment. Laney products have a heritage which stretches back to 1967 when I first began building valve amplifiers in my parent’s garage.
Laney 1 2 3 OPERATING INSTRUCTIONS 4 5 7 8 9 10 11 12 13 15 6 16 17 14 19 18 FRONT PANEL CONTROLS 1 The Mic input is designed for low impedance microphones, it is a balanced XLR socket so will work equally well with microphones that are balanced or unbalanced. Level controlled by 2 The Line In socket is designed for line level signals such as those obtained from keyboards, sound modules and sounds cards. Level controlled by Both mic and line in sockets may be used at the same time.
Laney 9 OPERATING INSTRUCTIONS This gain control allow you to adjust the level of instruments connected to the Channel 2 CD In and Line In sockets. 10 1/4” Jack socket designed to accept any line level signals from equipment such as keyboards, sound modules, CD/MP3 players and sounds cards. Level controlled by 11 11 This gain control allow you to adjust the level of instruments connected to the Channel 3 Line In socket.
Laney 1 OPERATING INSTRUCTIONS 2 3 4 5 6 FRONT PANEL CONTROLS 1 Power inlet socket. Connect to your power source. Make sure the specified voltage is correct for your country! 2 3 4 This drawer contains the main safety fuse for the unit. USE ONLY THE CORRECT SIZE AND RATING OF FUSE AS SPECIFIED ON THE PANEL. The mains fuse ratings are detailed in the specs section at the rear of this manual. Serial Number and model of your unit. This socket(s) should be used to connect an extension-cabinet.
Laney OPERATING INSTRUCTIONS OTHER FEATURES Your AH100 features a kick style design to enable you to use it as a stage monitor, or a conventional straight combo.
Laney SPECIFICATIONS D.I. BLOCK DIAGRAM Headphones Channel 1 Line In GAIN EQ SECTION VOLUME CD POWER AMP INTERNAL LOUDSPEAKER Channel 2 EXT. SPEAKER Line In Mic Remote GAIN Reverb VOLUME General Notes Amplifier connection: In order to avoid damage, it is advisable to establish and follow a pattern for turning on and off your equipment. With all system parts connected, turn on source equipment, tape decks, cd players, mixers, effects processors etc. BEFORE turning on your AUDIOHUB.
Laney SPECIFICATIONS Supply Voltage Mains Fuse Power Consumption Output Power THD%N Channel 1 Inputs Channel 2 Inputs Channel 3 Inputs Channel 1 EQ Channel 2 + 3 EQ (Shared) Reverb Ext Loudspeaker Internal loudspeaker DI / Main out Headphone Socket Size Unit weight Packing weight OPERATING INSTRUCTIONS ~100V, ~120V, ~220V, ~230V, ~240V 50/60Hz Factory Option ~230V = T1A L. ~100-120V = T2A L (Time delay) 100W 65W <0.
Laney POWER TO THE MUSIC METAL BLUES JAZZ ROCK AMPICONS ARE HERE TO HELP! @ In the interest of continued product development, Laney reserves the right to amend product specification without prior notification.