LV200 USER MANUAL
IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electric products, basic cautions should always be followed, including the following. 1. Read all safety and operating instructions before using this product 2. The product should be powered by a three pin `grounded (or earthed) plug connected to a power socket with a grounded earth outlet. 3. All safety and operating instructions should be retained for future reference 4. Obey all cautions in the Operating instructions and on the back of the unit 5.
Page 3 /12
Laney OPERATING INSTRUCTIONS BEFORE SWITCHING ON After unpacking your amplifier check that it is factory fitted with a three pin 'grounded' (or earthed) plug. Before plugging into the power supply ensure you are connecting to a grounded earth outlet. If you should wish to change the factory fitted plug yourself, ensure that the wiring convention applicable to the country where the amplifier is to be used is strictly conformed to.
Laney OPERATING INSTRUCTIONS Dear Player, Thank you very much for purchasing your new Laney product and becoming part of the worldwide Laney family. Each and every Laney unit is designed and built with the utmost attention to care and detail, so I trust yours will give you many years of enjoyment. Laney products have a heritage which stretches back to 1967 when I first began building valve amplifiers in my parent’s garage.
Laney 1 2 3 BRIGHT OPERATING INSTRUCTIONS 5 6 7 8 10 11 12 14 DRIVE 1 CLEAN CHANNEL 15 16 DRIVE 2 17 18 20 DRIVE EQUALISATION 21 22 REVERB TUBE ENABLED 200 INPUT VOLUME CLEAN BASS MIDDLE 4 TREBLE DRIVE 1 GAIN MASTER 9 DRIVE 2 GAIN MASTER BASS MIDDLE 13 CLEAN TREBLE 1 0 DRIVE POWER 19 FRONT PANEL CONTROLS 1 This socket should be used for connecting your instrument to the amplifier. Only use a good quality screened cable.
Laney OPERATING INSTRUCTIONS 11 Controls the overall level on the drive1 channel. Use in conjunction with 10 switch drastically cuts out any mid frequencies present in the drive2 sound giving you a very modern, 12 The VScoop aggressive lead tone. 13 Switch in to activate the drive2 channel. When active, control the amount of distortion with with The centre of the switch will be lit when active. 14 and the overall volume 15 14 Sets the level of gain on the drive2 channel.
Laney OPERATING INSTRUCTIONS 21 22 28 23 24 25 26 27 21 Power inlet socket. Connect to your power source. Make sure the specified voltage is correct for your country! 22 This drawer contains the main safety fuse for the unit. USE ONLY THE CORRECT SIZE AND RATING OF FUSE AS SPECIFIED ON THE PANEL The mains fuse ratings are detailed in the specs section at the rear of this manual 23 Displays the model number, power requirements and serial number of the unit.
Laney OPERATING INSTRUCTIONS QUICK START SETTINGS - suggestions only, experiment! BRIGHT DRIVE 1 CLEAN CHANNEL DRIVE 2 DRIVE EQUALISATION REVERB In 200 On INPUT VOLUME CLEAN BASS MIDDLE TREBLE DRIVE 1 GAIN MASTER DRIVE 2 GAIN MASTER BASS MIDDLE CLEAN TREBLE TUBE ENABLED 1 0 POWER DRIVE CLEAN SETTINGS BRIGHT DRIVE 1 CLEAN CHANNEL DRIVE 2 DRIVE EQUALISATION REVERB 200 On INPUT VOLUME CLEAN BASS MIDDLE TREBLE DRIVE 1 GAIN MASTER DRIVE 2 GAIN MASTER BASS MIDDLE
Laney OPERATING INSTRUCTIONS SAMPLE SYSTEM Laney Power To The Music RB115 LV412S Model Power Rating 300W Program Serial Number: SAMPLE DESIGNED IN THE UK BY LANEY www.laney.co.uk Input 8 Ohms Link General Notes Amplifier connection: In order to avoid damage, it is advisable to establish and follow a pattern for turning on and off your equipment. With all system parts connected, turn on source equipment, tape decks, cd players, mixers, effects processors etc. BEFORE turning on your guitar amplifier.
Laney OPERATING INSTRUCTIONS SPECIFICATIONS Supply Voltage Mains Fuse Power Consumption Output Power Rating Loudspeaker Features Footswitchable Reverb EQ Input Impedance Size Unit Weight Packing Weight ~100V, ~120V, ~220V, ~230V, ~240V 50/60Hz Factory Option ~220V>~240V = T1A L.
BLOCK DIAGRAM INPUT FX SEND FX RETURN CLEAN BRIGHT EQ SECTION VTS This loop is a series type so all of your signal will go through your FX unit. REVERB DRIVE1 SCOOP CLEAN REVERB DRIVE1 EQ SECTION DRIVE REVERB POWER AMP DRIVE1 SCOOP DRIVE2 INTERNAL LOUDSPEAKER ECC83 TUBE STAGE POWER ON MUTE EXT.