LX35R LX35 USER MANUAL
IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electric products, basic cautions should always be followed, including the following. 1. Read all safety and operating instructions before using this product 2. The product should be powered by a three pin `grounded (or earthed) plug connected to a power socket with a grounded earth outlet. 3. All safety and operating instructions should be retained for future reference 4. Obey all cautions in the Operating instructions and on the back of the unit 5.
Page 3 /12
Laney OPERATING INSTRUCTIONS BEFORE SWITCHING ON After unpacking your amplifier check that it is factory fitted with a three pin 'grounded' (or earthed) plug. Before plugging into the power supply ensure you are connecting to a grounded earth outlet. If you should wish to change the factory fitted plug yourself, ensure that the wiring convention applicable to the country where the amplifier is to be used is strictly conformed to.
Laney OPERATING INSTRUCTIONS Dear Player, Thank you very much for purchasing your new Laney product and becoming part of the worldwide Laney family. Each and every Laney unit is designed and built with the utmost attention to care and detail, so I trust yours will give you many years of enjoyment. Laney products have a heritage which stretches back to 1967 when I first began building valve amplifiers in my parent’s garage.
Laney 1 2 OPERATING INSTRUCTIONS 3 5 6 7 8 9 10 11 12 13 14 15 4 17 16 FRONT PANEL CONTROLS 1 This socket should be used for connecting your instrument to the amplifier. Only use a good quality screened cable. 2 Controls the volume level of the clean channel. 3 Switch in to activate the overdrive ‘Crunch’ channel. When active, control the amount of distortion with volume with 5 and the overall 6 4 Indicates that the drive channel is active.
Laney 8 Controls the amount of bass or bottom end present in your sound. 9 Controls the amount of mid present in you sound. OPERATING INSTRUCTIONS 10 Controls the amount of treble present in your sound. 11 Controls the amount of reverb applied to the signal. (LX35R only) 12 Fancy playing along with a backing track? Connect your CD/MP3 player here. 13 Connect a Laney FS2 footswitch here to enable remote switching for the channel and reverb/FX.
Laney 19 20 OPERATING INSTRUCTIONS 21 19 Power inlet socket. Connect to your power source. Make sure the specified voltage is correct for your country! This drawer contains the main safety fuse for the unit. 20 USE ONLY THE CORRECT SIZE AND RATING OF FUSE AS SPECIFIED ON THE PANEL The mains fuse ratings are detailed in the specs section at the rear of this manual 21 Displays the model number, power requirements and serial number of the unit.
Laney OPERATING INSTRUCTIONS QUICK START SETTINGS - Suggestions only, experiment! CLEAN SETTINGS DRIVE EQUALISATION LX35R 1 0 OUT INPUT VOLUME CRUNCH BLUES SETTINGS MASTER XTS BASS DRIVE MID TREBLE REVERB CD/LINE IN FOOTSWITCH EXT. SPKR EQUALISATION PHONES POWER LX35R 1 0 IN INPUT VOLUME CRUNCH ROCK LEAD SETTINGS MASTER XTS BASS DRIVE MID TREBLE REVERB CD/LINE IN FOOTSWITCH EXT.
Laney OPERATING INSTRUCTIONS BLOCK DIAGRAM HEADPHONES CD IN INPUT CLEAN EQ SECTION XTS REVERB / EFFECTS POWER AMP INTERNAL LOUDSPEAKER EXTERNAL LOUDSPEAKER DRIVE FOOTSWITCH General Notes Amplifier connection: In order to avoid damage, it is advisable to establish and follow a pattern for turning on and off your equipment. With all system parts connected, turn on source equipment, tape decks, cd players, mixers, effects processors etc. BEFORE turning on your guitar amplifier.
Laney SPECIFICATIONS Supply Voltage Mains Fuse Power Consumption Output Power Rating Loudspeaker Features Springline Reverb EQ Input Impedance Size Unit Weight Packing Weight OPERATING INSTRUCTIONS ~100V, ~120V, ~220V, ~230V, ~240V 50/60Hz Factory Option ~220V>~240V = T250mA L.
Laney POWER TO THE MUSIC METAL BLUES JAZZ ROCK AMPICONS ARE HERE TO HELP! @ In the interest of continued product development, Laney Reserves the right to amend product specification without prior notification.