Vs IMPORTANT SAFETY INSTRUCTIONS \ WARNING: When using electrical products, basic cautions should always be followed, including the following: 1. Read these Instructions. 2. Keep these instructions safe. 3. Heed all wakings. 4. Follow all instructions. 5. Do not use this apparatus near water. 8. Clean only with a dry cloth. 7. Do net bock any of the ventilation openings. Install In accordance with manufacturer's Instructions. 8.
I= a JS FCC Com pliancy Statement This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference 2) This device must accept any interference received, that may cause undesired operation. Warning: Changes or modification to the equipment not approved by Lana can void the user's authority to use the equipment.
WELCOME \ Dear Player, Thank you very much for purchasing your new Lana product and becoming part of the worldwide Lana family). Sachs and every Lana unit is designed and built with the utmost attention to care and detail, so 1 trust yours will give You many Years of enjoyment. Lana products have a heritage which stretches back t 1965 whew 1 first began building valve amplifiers tn my parent's garage. Stine then we have moved on.
J INTRODUCTION | Forged deep within the Black Country the metal beating industrial heartland of the UK where the sound of metal guitar was bom, comes the IRON HEART. I RON E ART With molten metal flowing through its circuits, IRON HEART continues the legacy passed on by previous Lana amps such as LIPPI and AOR, and hits you hard between the eyes like a power hammer from hell.
FRONT PANEL CONTROLS 000 15W INPUT: Mono jack socket. Connect your guitar here to get full volume output. Use only high quality guitar cable. <1W INPUT: Mono Jack socket. Connecting your guitar here switches the output stage to under 1W. This allows you to drive the output stage hard at bedroom volume levels. Note: Both sockets should not be used simultaneously. PER-BOOST SWITCH: Switches the input boost circuit on or off.
J FRONT PANEL CONTROLS FREE ren @ he LEAD VOLUME: Controls the Lead channel volume. Experiment with different combinations of the Drive and Volume controls to achieve different sounds. Reducing the Drive while increasing the Volume will result in a warm, open, overdrive sound as the power amp is driven harder, while reducing the Volume and increasing the Drive will give a tighter, more modem sound with more distortion.
Vs REAR PANEL CONTROLS \ =, Ens © ool © ® MAINS INLET SOCKET MAINS FUSE: Make sure the voltage indicated on the rear panel is correct for your country! This drawer contains the main safety fuse for the unit. The fuse protects the amplifier from damage in the event of fault by disconnecting the mains power supply. ®@ HT FUSE: This fuse disconnects the high voltage DC power to the tubes within the amplifier in the event of a fault. Replacing fuses USE ONLY THE CORRECT SIZE AND RATING SPECIFIED ON THE PANEL.
J REAR PANEL CONTROLS ®@ @—C— OM USB: Record replay connector, (Dry on left channel, processed on right channel). USB2.0 is compatible with Windows XP ® operating system, Windows 7 ® operating system & Windows 8 ® operating system. Also compatible with Mac ® & iPad ®1-3 via camera USB adapter, iPad ® 4 & iPad Mini @ via Lightning-USB camera adapter cable. wm Dry signal send with level control e-12dB gain to optimist record levels.
SPECIFICATIONS \ FT LRT Supply Voltage: Factory ~100V, ~120V, ~220V, ~230V, ~240V 50/60Hz Mains Fuse: T500mAL Carton Contents | T250mAL o . TT Fuse T100mAL IT-Studio Amplifier Power Consumption B80W F84-IRT Fe h Output Power Rating 15W SHIRT Footstool Channels 3 Clean, Rhythm & Lead L l Features: | High and low power input sockets 5 pin Foot switch Cable Pr-Boost Input Control 12AX7/ECC83 preamble tubes Mains Cable 2 PIXEL output tubes | Emulated DI & Phones with Level control User Manual 3.
SUBSUMPTION \ Tube amplifiers generally sound much warmer/sweeter than solid state transistor amplifiers but they also need a little more respect due to the fragile glass tubes. The IT-Studio uses three 12AX7 preamble tubes, and 2 ELL output tubes which should give you years of trouble free service, however like all tube amps; it is important to treat it with a certain amount of care. Use the following steps as a guide for how to take care of your amplifier: HW Take care when moving the amplifier.
SIGNAL PATH BLOCK DIAGRAM \ Gutter Input: Sand Raul AuxfCDMP3 Input Always switch off and disconnect power cord when not in use
J USB INTERFACE FOR PC, MAC & IPAD USB Interface options: mn USB2.0 Bidirectional to PC/Mac/iPad etc. mn Record output of amplifier with or without a speaker load connected m Simultaneously record dry guitar signal for later processing or Re-Umping. = Re-Amp guitar track changing the settings as required nm Re-Amp guitar track with textual stomp boxes as required nm Add tube amplifier and/or power amplifier warmth to digital guitar tracks with or without speaker load.
USB INTERFACE FOR PC, MAC & IPAD \ IRT Studio USB Recording: \ iPad/MAC/PC Optional Speaker Load Recording Device Guitar Input Connect your USB recording device (PC/MAC or iPad) via an appropriate USB cable. Your amplifier will send two audio tracks to your recording device: {1) On the Left channel the direct unaffected guitar signal. {This can be used at a later date for (2) On the Right channel! the amplified fully processed signal.
~N J USB INTERFACE FOR PC, MAC & IPAD IRT Studio USB Optional Speaker Load iPad/MAC/PC Recording Device USB Connect USB cable as for recording. Then connect a good quality screened guitar cable from the rear panel “Re-Amp” output jack and loop round the front panel to guitar Input jack. (Route lead in an anti-clockwise direction around the amplifier to avoid hum pick-up from the power transformer) Output the original unprocessed guitar track by monitoring it on your record device.
USB INTERFACE FOR PC, MAC & IPAD IRT Studio USB “Re-Umping” with added Stomp box Effects: Proceed as for normal "Re-Umping” except in this case inert your FX box/s into the Guitar lead from the Re Amp out jack to the Guitar amplifier input. The recorded Left channel! will contain the original unprocessed signal now with your effects only added. The right channel will contain the same sound but also processed via the Studio amplifier.
J RACK MOUNTING Ventilation: Ensure the amplifier is well ventilated and that the ventilation slots in the top, bottom & sides are not obstructed in any way. Avoid dropping anything in through the vents especially liquids of any kind. If this should happen turn off the product and disconnect from the power supply immediately and leave to dry out for at least 24hrs. Seek help from a qualified service engineer.
