WARNING: When using electrical products, basic cautions should always be followed, including the following: 1. Read these instructions. 2. Keep these instructions safe. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any of the ventilation openings. Install in accordance with manufacturer’s instructions. 8.
ATTENTION: L’utilisation de tout appareil électrique doit être soumise aux precautions d’usage incluant: 1. Lire ces instructions 2. Gardez ce manuel pour de futures références. 3. Prétez attention aux messages de précautions de ce manuel. 4. Suivez ces instructions. 5. N’utilisez pas cette unité proche de plans d’eau. 6. N’utilisez qu’un tissu sec pour le nettoyage de votre unité. 7.
ACHTUNG: Beim Einsatz von Elektrogeräten müssen u.a. grundlegende Vorsichtsmaßnahmen befolgt werden: 1. Lesen Sie sich diese Anweisungen durch. 2. Bewahren Sie diese Anweisungen auf. 3. Beachten Sie alle Warnungen. 4. Befolgen Sie alle Anweisungen. 5. Setzen Sie dieses Gerät nicht in der Nähe von Wasser ein. 6. Reinigen Sie es nur mit einem trockenen Tuch. 7. Blockieren Sie keine der Lüftungsöffnungen. Führen Sie die Installation gemäß den Anweisungen des Herstellers durch. 8.
CUIDADO: Cuando use productos electrónicos, debe tomar precauciones básicas, incluyendo las siguientes: 1. Lea estas instrucciones. 2. Guarde estas instrucciones. 3. Haga caso de todos los consejos. 4. Siga todas las instrucciones. 5. No usar este aparato cerca del agua. 6. Limpiar solamente con una tela ceca. 7. No blacker ninguna de las salida de ventilación. Instalar de acuerdo a las instrucciones del fabricante. 8.
SPECIFICATIONS Supply Voltage:- Factory Preset Mains Fuse: ~100V>~120V ~220V>~240V HT Fuse Power Consumption Output Power Rating Features: Loudspeaker Outputs Input Impedance Size Unit Weight Packed Weight ~100V, ~120V, ~220V, ~230V, ~240V 50/60Hz T500mA L T250mA L T100mA L 50W 15W High and low power input sockets (15W/<1W) Footswitchable Pre-Boost - LED indicates active EQ - Passive Bass, Middle & Treble Volume Dynamics & Tone Master controls Emulated DI & Phones 3.
Forged deep within the Black Country - the metal beating industrial heartland of the UK - where the sound of metal guitar was born, comes the IRONHEART. With molten metal flowing through its circuits, IRONHEART continues the legacy passed on by previous Laney amps such as KLIPP and AOR, and hits you hard between the eyes like a power hammer from hell.
FRONT PANEL CONTROLS 15W INPUT: 1/4" mono jack socket. Connect your guitar here to get full volume output. Use only high quality guitar cable. <1W INPUT: 1/4" mono jack socket. Connecting your guitar here switches the output stage to under 1W. This allows you to drive the output stage hard at bedroom volume levels. Note: Both sockets should not be used simultaneously. PRE-BOOST SWITCH: Switches the input boost circuit on or off.
FRONT PANEL CONTROLS VOLUME: Controls the volume of the amplifier. Experiment with different combinations of the Drive and Volume controls to achieve different sounds. Reducing the Drive while increasing the Volume will result in a warm, open, overdriven sound as the power amp is driven harder, while reducing the Volume and increasing the Drive will give a tighter, more modern sound with more distortion. Once set, try using your guitar's volume controls to interactively adjust tone and distortion levels.
REAR PANEL CONTROLS LZB1 2 3 4 Spare fuse located in the fuse drawer. MAINS INLET SOCKET: Make sure the voltage indicated on the rear panel is correct for your country! MAINS FUSE: This drawer contains the main safety fuse for the unit. The fuse protects the amplifier from damage in the event of fault by disconnecting the mains power supply. POWER SWITCH: Main power switch for the unit.
REAR PANEL CONTROLS FX RETURN: 1/4" mono jack socket for the connection of the output of an external FX unit. This can also be used as a slave in for the power amp. As the FX Loop is an insert type, this will mute the preamp signal. FX LOOP SWITCH: Selects the FX Loop mode of operation: ! Bypass - Removes the FX Loop from the signal path. ! 0 dBu - For connection of FX units with a 0dBu nominal output level. ! -10dBu - For connection of FX units with a -10dBu nominal output level.
QUICK START SETTINGS CLEAN CRUNCH LEAD METAL
USER SETTINGS
TUBE AMP TIPS Tube amplifiers generally sound much warmer/sweeter than solid state transistor amplifiers but they also need a little more respect due to the fragile glass tubes. The IRT15H head uses three 12AX7 preamp tubes, and 2 EL84 output tubes which should give you years of trouble free service, however like all tube amps; it is important to treat it with a certain amount of care. Use the following steps as a guide for how to take care of your amplifier: ! Take care when moving the amplifier.
BLOCK DIAGRAM FX SEND INPUT FX RETURN <1W DRIVE VOLUME EQ Pre-Boost MID BASS TREBLE DI OUT 15W BYPASS 0dBu -10dBu REVERB MUTE PHONES FOOTSWITCH CD/MP3 IN (3.
SAMPLE SETUPS FX Unit LZB1 2 3 4 RECORD OUT MP3 IRT212 FS2
NOTES