Operators Guide LD060/LD075 Copy Reference Guide you r docu ment m an a ge m ent pa r tne r
Paper type: Wood Free 80g/m2, Paper Thickness=100 µm // Pages in book=136 // Print scale=81% Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 6.800000 mm Introduction This manual contains detailed instructions on the operation and maintenance of this machine. To get maximum versatility from this machine all operators should carefully read and follow the instructions in this manual. Please keep this manual in a handy place near the machine.
MartiniC1_GBcopy4_FM.book Page i Tuesday, April 23, 2002 6:23 PM What You Can Do With This Machine The following sections introduce the duplex and combining functions of this machine. Types of Duplex Copies 1-sided 2 Pages 2-sided 1 Page " 1 Sided 2 Sided" p.43 2-sided 1 Page 2-sided 1 Page " 2 Sided 2 Sided" p.43 1-sided 4 Pages 2-sided 1 Page p.47 " 1 Sided 4 Pages Combine 2 Side" 2-sided 2 Pages 2-sided 1 Page p.47 " 2 Sided 4 Pages Combine 2 Side" 1-sided 8 Pages 2-sided 1 Page p.
MartiniC1_GBcopy4_FM.book Page ii Tuesday, April 23, 2002 6:23 PM Copying Book Originals 1-sided 4 Pages Booklet ( P.50 " 1 Sided Booklet") Open to Left 1 2 3 2 3 3 1 4 4 1 Open to Right 1 2 3 3 3 2 4 1 1 4 2-sided 2 Pages Booklet ( P.51 " 2 Sided Booklet") Open to Left 3 1 Open to Right 3 1 1-sided Magazine ( P.51 " 1 Sided Magazine") Open to Left 1 2 5 2 7 8 7 1 4 8 1 3 5 3 6 Open to Right 1 2 5 7 7 2-sided 8 2 8 Magazine ( 1 P.
MartiniC1_GBcopy4_FM.book Page iii Tuesday, April 23, 2002 6:23 PM Combining Multiple Pages onto a Single Page ( p.45 "1 Sided Combine") 1-sided 2 Pages 1-sided 1 Page 2-sided 1 Page 1-sided 4 Pages 1-sided 1 Page 2-sided 2 Pages 1-sided 1 Page 1-sided 8 Pages 1-sided 1 Page 2-sided 4 Pages 1-sided 1 Page Copying Originals Such as Books ( p.48 "Series Copies") Bound Originals 1-sided Pages Bound Originals 2-sided Pages 1-sided 1 Page Copying 2-Sided Pages onto 1-Sided Pages ( P.
MartiniC1_GBcopy4_FM.book Page iv Tuesday, April 23, 2002 6:23 PM TABLE OF CONTENTS What You Can Do With This Machine ................................................................... i How to Read this Manual ......................................................................................1 Machine Types .......................................................................................................2 Functions that Require Options .............................................................
MartiniC1_GBcopy4_FM.book Page v Tuesday, April 23, 2002 6:23 PM Series Copies........................................................................................................... 48 2 Sided→1 Sided ..................................................................................................... 50 Copying Book Originals............................................................................................ 50 Image Repeat.......................................................................
MartiniC1_GBcopy4_FM.book Page vi Tuesday, April 23, 2002 6:23 PM 5. User Tools (Copy/Document Server Features) User Tools Menu (Copier/Document Server Features) .................................... 89 Accessing User Tools (Copy/Document Server Features) .............................. 96 Exiting From User Tools........................................................................................... 96 General Features 1/5 ...................................................................................
MartiniC1_GBcopy4_FM.book Page 1 Tuesday, April 23, 2002 6:23 PM How to Read this Manual Symbols In this manual, the following symbols are used: R WARNING: This symbol indicates a potentially hazardous situation that might result in death or serious injury when you misuse the machine without following the instructions under this symbol. Be sure to read the instructions, all of which are included in the Safety Information section in the General Settings Guide.
MartiniC1_GBcopy4_FM.book Page 2 Tuesday, April 23, 2002 6:23 PM Machine Types This machine comes in two models which vary by copy speed. To make sure which model you have, see the inside front cover.
MartiniC1_GBcopy4_FM.book Page 3 Tuesday, April 23, 2002 6:23 PM Functions that Require Options ❍ ❍ Punch ❍ Staple (Saddle Stitch) Staple Finisher 3000M(50-sheet staples) Stack Tab Sheet Holder Shift Sort Functions Copying onto the Tab Stock Available functions depend on your machine configuration and which options you have. See the table below.
MartiniC1_GBcopy4_FM.book Page 4 Tuesday, April 23, 2002 6:23 PM Control Panel Note ❒ This illustration shows the Control Panel of the machine with options fully installed. ZGVH010E 1. Screen Contrast knob 6. {Program}} key Adjusts the brightness of the display panel. Press to store or recall a program. ⇒ p.79 “Programs” 2. Indicators 7. {Clear Modes}} key These indicators show the status of the machine or indicate errors. ⇒ “Control Panel” in the General Settings Guide.
MartiniC1_GBcopy4_FM.book Page 5 Tuesday, April 23, 2002 6:23 PM 11. Operation switch 15. {Clear/Stop}} key Press this switch to turn the power on (the On indicator goes on). To turn the power off, press this switch again (the On indicator goes off). ⇒”Turning On the Power” in the General Settings Guide. • Clear Press to delete a number entered. 12. Clip Tray • Stop Press to stop a copy job in progress. Press to stop Scanning and printing in Document Server mode. Holds clips and staples. 16.
MartiniC1_GBcopy4_FM.
MartiniC1_GBcopy4_FM.book Page 7 Tuesday, April 23, 2002 6:23 PM 1.
MartiniC1_GBcopy4_FM.
MartiniC1_GBcopy4_FM.book Page 9 Tuesday, April 23, 2002 6:23 PM Originals ❖ Exposure glass 1 ❖ Document feeder Sizes difficult to detect It is difficult for the machine to detect the sizes of the following originals, so select manually.
MartiniC1_GBcopy4_FM.book Page 10 Tuesday, April 23, 2002 6:23 PM Placing Originals Missing Image Area Even if you correctly place originals in the document feeder or on the exposure glass, margins of a few millimeters on all four sides of the original might not be copied. 1 1. 0.5 mm, 0.02” 2. 1 mm or more, 0.04” or more 10 3. 0.5 mm - 3.5 mm, 0.02” - 0.14” 4. 2 - 6 mm, 0.08”- 0.
MartiniC1_GBcopy4_FM.book Page 11 Tuesday, April 23, 2002 6:23 PM Originals Direction-fixed paper or 2-sided paper Direction-fixed (top to bottom) or 2-sided paper (e.g., letterhead paper, punched paper, or copied paper) might not be printed correctly depending on how the originals and paper are placed. Set "Letterhead setting" in system settings, and then place the original and paper as shown below. ⇒ p.
MartiniC1_GBcopy4_FM.book Page 12 Tuesday, April 23, 2002 6:23 PM Placing Originals Placing Originals Note ❒ Place originals after correction fluid and ink have completely dried. Not taking this precaution could dirty the exposure glass with marks that will be copied. 1 Example: When you want to staple copies, but you cannot select because the original size is A3K, selecting enables you to staple copies correctly. Reference For document sizes you can set. ⇒ p.7 “Originals”.
MartiniC1_GBcopy4_FM.book Page 13 Tuesday, April 23, 2002 6:23 PM Placing Originals Placing Originals on the Exposure Glass Reference Related Initial Settings ⇒ p.108 “Eject Copy Face Up/Down in Glass” A Lift the exposure glass cover or the document feeder. Important ❒ Do not open the exposure glass cover or the document feeder forcefully. Otherwise, the cover of the document feeder might open or be damaged. Note ❒ Be sure to open the exposure glass cover or the document feeder by more than 30°.
MartiniC1_GBcopy4_FM.book Page 14 Tuesday, April 23, 2002 6:23 PM Placing Originals A Set the document guide to the original size. B Align the edges of the original and place it on the document feeder (ADF) with the side to be copied facing up. 1 Batch mode In batch mode, the machine copies an original of more than 100 pages as one document, even if it is placed on the document feeder in parts. Important ❒ When placing special originals such as translucent paper, place one by one.
MartiniC1_GBcopy4_FM.book Page 15 Tuesday, April 23, 2002 6:23 PM Placing Originals SADF mode Mixed Size mode In SADF mode, even when an original is placed page by page in the document feeder (ADF), each page is automatically fed when placed. When you place different size originals in the document feeder at the same time, the machine automatically checks the size of the originals and makes copies.
MartiniC1_GBcopy4_FM.book Page 16 Tuesday, April 23, 2002 6:23 PM Placing Originals C Align the rear and left edges of originals as shown in the illustration. 1 1 the horizontal size of the original with the Number keys, and then press the [#] key. Note ❒ If you make a mistake, press the [Print Inquiry List] or {Clear/Stop} } key, and then enter the value again. B4 A3 2 CP19AE 1. Place into the document feeder. 2. Vertical size D Adjust the guide to the widest original size.
MartiniC1_GBcopy4_FM.book Page 17 Tuesday, April 23, 2002 6:23 PM 2. Copying Basic Procedure A When the machine is set for user codes, enter a user code (up to 8 digits) with the number keys, and then press the {#} } key. The machine is ready to copy. Reference For Users Code, see ⇒“Key Operator Tools” in the General Settings Guide. B Make sure "Ready" is displayed on the screen. If any other function is displayed, press the {Copy} } key.
MartiniC1_GBcopy4_FM.book Page 18 Tuesday, April 23, 2002 6:23 PM Copying Auto Start Copy starts automatically when the machine is ready. A Set the copy contents while “Select copy mode and press {Start} }” and “Scanning originals can be started” are displayed alternately. 2 B Set the original. C Press the {Start}} key. The machine scans the original. When the machine is ready, it starts copying automatically.
MartiniC1_GBcopy4_FM.book Page 19 Tuesday, April 23, 2002 6:23 PM Basic Procedure Copy Face Up Use this function to reverse the order of copies. Preparation Before using this function, register "Face up" for a copy function key. ⇒ p.99 “Copy Function Key: F1– F5” A Press {Face Up}} key. B Set up the next copy job. C Place the originals in the document feeder, and then press the {Start} } key. All originals are scanned. After the current copy job, the next job starts automatically.
MartiniC1_GBcopy4_FM.book Page 20 Tuesday, April 23, 2002 6:23 PM Copying To check job contents B Select the number of the job you A Check contents. B Press the [Confirmed] key. C Press the [Delete Job] key. D Press the [Delete] key. You return to the Reserved Job screen. 2 want to delete. You return to the Reserved Job screen. To change job contents after checking Copying onto Tab Stock A Check job contents. B Change contents and You can copy onto tab stock. press the [Confirmed] key.
MartiniC1_GBcopy4_FM.book Page 21 Tuesday, April 23, 2002 6:23 PM Basic Procedure Important ❒ When you set tab stock, be sure to use the optional tab sheet fence. 1 2 3 2 ❒ Set tab stock so that it will be fed from the side without the tab first. ❒ Adjust the back fence position so that the tab sheet fence will fit the tab stock. 1. Originals 2. Tab stock 3. Copies A Select the paper tray where the tab sock is set. B Place originals, and then press the {Start} } key.
MartiniC1_GBcopy4_FM.book Page 22 Tuesday, April 23, 2002 6:23 PM Copying Copying from the Bypass Tray Use the bypass tray to copy onto special paper (OHP transparencies, label paper, adhesive labels), thick paper (postcards and thin paper), and copy paper that cannot be loaded in the paper trays. 2 Preparation When copying from the bypass tray, select [1 Sided→ → 1 Sided] for copying in [Dup./Combine/Series]. You can change the initial settings. ⇒ p.
MartiniC1_GBcopy4_FM.book Page 23 Tuesday, April 23, 2002 6:23 PM Copying from the Bypass Tray A Open the bypass tray. C Select the type and size of the paper. When copying onto standard size paper A Press the {#} } key. B Press the [Select Size] key. C Select the paper size. D Press the [OK] key. B Insert copy paper with the side you want to copy facing up, pusing until you hear the beep, and then align the paper guide to the paper size. 1.
MartiniC1_GBcopy4_FM.book Page 24 Tuesday, April 23, 2002 6:23 PM Copying When copying onto special paper A Press the {#} } key. B Select paper type in "Special paper". C Press the [OK] key. D Place 2 your originals, and then press the {Start} } key. E When your copy job is finished, press the { Clear Modes} } key to clear the settings.
MartiniC1_GBcopy4_FM.book Page 25 Tuesday, April 23, 2002 6:23 PM Copy Functions Copy Functions Adjusting Copy Image Density B Press the [Lighter] or [Darker] key to adjust image density. There are three types of adjustment available: 2 ❖ Auto image density The machine automatically adjusts the image density. ❖ Manual image density You can adjust the density of the original in seven increments.
MartiniC1_GBcopy4_FM.book Page 26 Tuesday, April 23, 2002 6:23 PM Copying Selecting Original Type Setting When the original type keys are not displayed Select one of the following five types to match your originals: A Press the [Original Type] key. B Select the original type, and then press the [OK] key. ❖ Text Select this mode when your originals contain only text (no pictures). 2 ❖ Photo Delicate tones in photographs and pictures can be reproduced with this mode.
MartiniC1_GBcopy4_FM.book Page 27 Tuesday, April 23, 2002 6:23 PM Copy Functions Selecting Copy Paper There are two ways to select copy paper: ❖ Auto Paper Select The machine selects a suitable size of copy paper automatically, based on original size and reproduction ratio. 2 ❖ Manual Paper Select Choose the tray containing the paper you wish to copy onto: a paper tray, bypass tray or large capacity tray (LCT). Reference ⇒ p.
MartiniC1_GBcopy4_FM.book Page 28 Tuesday, April 23, 2002 6:23 PM Copying Auto Paper Select A Make sure that the [Auto Paper Select] key is selected. 2 Note ❒ Trays with a key mark will not be automatically selected. ⇒ "Paper Size Settings" in the General Settings Guide Manual Paper Select A Select the paper tray, bypass tray or large capacity tray (LCT). The indicator corresponding to the selected paper tray is highlighted. Reference ⇒ p.
MartiniC1_GBcopy4_FM.book Page 29 Tuesday, April 23, 2002 6:23 PM Copy Functions - Rotated copy If the direction in which your original is placed (L or K) is different from that of the paper you are copying onto, this function rotates the original image by 90° and fits it on the copy paper. This function works when Auto Paper Select or Auto Reduce/Enlarge is selected. ⇒ p.27 “Auto Paper Select” 2 R R Note ❒ The default setting for "Auto Tray Switching" is "With image rotation ".
MartiniC1_GBcopy4_FM.book Page 30 Tuesday, April 23, 2002 6:23 PM Copying Preset Reduce/Enlarge A Press the [Reduce/Enlarge] key. You can select a preset ratio for copying. 2 ❖ Base Point The base point of Enlarge/Reduce differs depending on how the original is scanned. When the original is set on the exposure glass, the upper left corner will be the base point. When it is set to the document feeder, the bottom left corner of the original will be the base point. 1.
MartiniC1_GBcopy4_FM.book Page 31 Tuesday, April 23, 2002 6:23 PM Copy Functions - Create Margin Mode Use "Create Margin" to reduce the image to 93% of its original size with the center as reference. By combining it with the Reduce/Enlarge function, you can also provide the Reduce/Enlarge copy with a margin. Zoom You can change the reproduction ratio in 1% steps. 2 Reference Related Initial Settings A ⇒ p.99 “Copy Function Key: F1– F5” ⇒ p.
MartiniC1_GBcopy4_FM.book Page 32 Tuesday, April 23, 2002 6:23 PM Copying Note ❒ To change the ratio in 1% steps, just press the {n} or {o} keys. To change the ratio in 10% steps, press and hold down the {n} or {o} keys. 2 ❒ If you have incorrectly entered the ratio, readjust the ratio with the [n n ] or [o o] keys.
MartiniC1_GBcopy4_FM.book Page 33 Tuesday, April 23, 2002 6:23 PM Copy Functions E Enter the length of the copy with Size Magnification This function calculates an enlargement or reduction ratio based upon the lengths of the original and copy. A mm a mm the number keys, and then press the [#] key. Note ❒ To change the length after pressing the [#] key, select [Original] or [Copy] and enter the desired length. F Press the [OK] key. G Press the [OK] key. H Place your original, press the {Start} } key.
MartiniC1_GBcopy4_FM.book Page 34 Tuesday, April 23, 2002 6:23 PM Copying A Press the [Reduce/Enlarge] key. D Press the [Vertical] key. E Adjust the ratio with the [n n] or [o o] keys. F Press the [OK] key. D Press the [OK] key. E Place your originals, 2 press the {Start} } key. B Press the [Specifd. Ratio] key. C Press the [Direct. Mag.%] key. To enter a ratio with the number keys A Press the [Horizontal] key. B Enter the desired ratio with the number keys, followed by the [#] key.
MartiniC1_GBcopy4_FM.book Page 35 Tuesday, April 23, 2002 6:23 PM Copy Functions ❒ You can enter sizes within the following ranges. Metric version Vertical: 1 – 999 mm (in 1 mm steps) Horizontal: 1 – 9999 mm (in 1 mm steps) Inch version Vertical: 0.1” – 99.9” (in 0.1” steps) Horizontal: 0.1” – 99.9” (in 0.1” steps) A Press the [Reduce/Enlarge] key. B Press the [Specifd. Ratio] key. C Press the ["Dir. Size Mag mm"] key.
MartiniC1_GBcopy4_FM.book Page 36 Tuesday, April 23, 2002 6:23 PM Copying ❖ Shift Sort • The optional Finisher 3000B (100–sheet staples), Finisher 3000M(50–sheet staples) or Booklet finisher is required to use this function. Each time the copies of one set or those of a different job are delivered, the next copy set is shifted when delivered, so that you can separate sets or jobs. 2 ❖ When the Booklet Finisher is installed B Enter the number of copy sets with the number keys.
MartiniC1_GBcopy4_FM.book Page 37 Tuesday, April 23, 2002 6:23 PM Copy Functions Stack Staple This function collates copies of pages from a multi-page original. Stacks of each page's copies are shifted for ease of separation. An optional finisher is required to use this function. Each copy set can be stapled together. 2 2 3 222 111 333 1 A Press the [Stack] key.
MartiniC1_GBcopy4_FM.book Page 38 Tuesday, April 23, 2002 6:23 PM Copying Stapling position and original setting ❖ Finisher 3000M(50–sheet staples) Original logation Place all the originals in the automatic document feeder (ADF) in the orientation in which they can be read normally. When placing the original on the exposure glass, keep the same orientation, but set the original facing downwards.
MartiniC1_GBcopy4_FM.book Page 39 Tuesday, April 23, 2002 6:23 PM Copy Functions ❖ Booklet Finisher A Select Original logation Document Feeder Stapling position ❖ Finisher 3000B(100–sheet staples), Finisher 3000M(50–sheet staples) Top Exposure glass one of the stapling posi- tions. Left 2 Bottom Top slant 2 Top 2 Note ❒ The stapling position will be fixed to “Top”. Saddle stitch ❖ Booklet Finisher ZGVX100E *1 *2 *3 This table shows staple positioning.
MartiniC1_GBcopy4_FM.book Page 40 Tuesday, April 23, 2002 6:23 PM Copying Note ❒ When placing originals on the exposure glass, start with the first page to be copied. When placing originals in the document feeder (ADF), set so that the last page is on the bottom. ❒ When placing original on the exposure glass or in the document feeder (ADF) using batch mode, press the {#} } key after all have been scanned.
MartiniC1_GBcopy4_FM.book Page 41 Tuesday, April 23, 2002 6:23 PM Copy Functions Punch The optional finisher and punch unit are required to use this function. This function is used to make punch holes in copies. ❖ 2 holes 2 ❖ 3 holes ❖ 4 holes Note ❒ You cannot use the bypass tray with this function. ❒ The 4 – hole punch type is only capable of punching in the 4 – hole format.
MartiniC1_GBcopy4_FM.book Page 42 Tuesday, April 23, 2002 6:23 PM Copying Punch hole positions Direction in which Original is Set Exposure glass 2 holes Punch Hole Positions *1 Document feeder K 2 L Standard 3 holes K L 4 holes K L 2 holes K L 90º Turn 3 holes K L 4 holes K L *1 42 This table shows the punch hole positions. The orientation of the paper does not indicate direction of delivery.
MartiniC1_GBcopy4_FM.book Page 43 Tuesday, April 23, 2002 6:23 PM Copy Functions A Select the punch position. 2 B Place your originals, then press the {Start}} key. Duplex Originals and Copy Direction There are two types of duplex. You can select the orientation. • Top to Top ❖ 1 Sided → 2 Sided Copies two 1–side pages onto one 2–sided page. Duplex1 1 • Top to Bottom 1 2 2 Duplex2 ❖ 2 Sided → 2 Sided Copies one 2–sided page onto one 2–sided page.
MartiniC1_GBcopy4_FM.book Page 44 Tuesday, April 23, 2002 6:23 PM Copying Original Direction and Completed Copies A Press the {Dup./Combine/Series} } key. The resulting copy image will differ according to the direction in which you place your original (widthwise K or lengthwise L). 2 B Select the ([1 Sided]/[2 Sided]) key for "Original", and then press the ([1 Sided]/[2 Sided]) key for "Copy".
MartiniC1_GBcopy4_FM.book Page 45 Tuesday, April 23, 2002 6:23 PM Copy Functions 1 Sided Combine Combine several pages onto one side of a sheet. ❖ 2 Sided, 1 Page → Combine 1 Side Copies one 2-sided original to one side of a sheet. ❖ 1 Sided, 2 Pages → Combine 1 Side Copies two 1-sided originals to one side of a sheet. 1 1 2 2 2 GCSHVYOE 1 2 1 2 ❖ 2 Sided, 2 Pages → Combine 1 Side Copies two 2-sided originals to one side of a sheet.
MartiniC1_GBcopy4_FM.book Page 46 Tuesday, April 23, 2002 6:23 PM Copying ❖ Orientation of the Original and Image Position of Combine Open to Left R Originals A Press the [Dup./Combine/Series] key. 2 Open to Top S Originals B Press the ([1 Sided]/[2 Sided]) key for "Original", and then press the [Combine 1 Side] key for "Copy".
MartiniC1_GBcopy4_FM.book Page 47 Tuesday, April 23, 2002 6:23 PM Copy Functions 2 Sided Combine Combines various pages of originals onto one sheet with two sides. ❖ 1 Sided, 16 Pages → Combine 2 Side Copies sixteen 1-sided originals to one sheet with eight pages per side. 1 ❖ 1 Sided, 4 Pages → Combine 2 Side Copies four 1-sided originals to one sheet with two pages per side. 1 2 3 4 2 5 6 7 8 2 1 15 16 1 2 1 9 10 11 12 13 14 15 16 2 3 2 4 GCSHVY5E 4 3 1. Front 2.
MartiniC1_GBcopy4_FM.book Page 48 Tuesday, April 23, 2002 6:23 PM Copying ❖ 2 Sided, 16 Pages → Combine 2 Side Copies eight 2-sided originals to one sheet with eight pages per side. 1 for "Original", and then press the [Combine 2 Side] key for "Copy". 1 2 3 4 3 5 6 7 8 2 2 B Press the ([1 Sided]/[2 Sided]) key 4 1 13 15 14 16 9 10 11 12 13 14 15 16 2 GCSHVY6E 1. Front 2. Back Note ❒ You cannot use the bypass tray with this function. Reference ⇒ p.
MartiniC1_GBcopy4_FM.book Page 49 Tuesday, April 23, 2002 6:23 PM Copy Functions ❖ Book → 2 Sided Copies a two-page spread original onto one sheet with one page per side. 1 2 3 Paper for 1– sided copy 11" × 17"L 81/2" × 11"K × 2 sheets 81/2" × 11"L 51/2" × 81/2"K × 2 sheets 2 ❒ See the following table for original and copy paper sizes when making 1 sided copies using a 100% ratio. ❖ Front & Back → 2 Sided Copies each two-page spread original as it is onto both sides of a sheet.
MartiniC1_GBcopy4_FM.book Page 50 Tuesday, April 23, 2002 6:23 PM Copying E Make sure that the [Auto Paper Select] key is selected. F Place your originals on the expo- B Press the [2 Sided] key for the original, then press the [1 Sided] key for the copy. sure glass, and then press the {Start} } key. Note ❒ Press the {#} } key after all originals have been scanned. 2 2 Sided→ →1 Sided You can make one-sided copies from two-sided originals. Reference ⇒ p.
MartiniC1_GBcopy4_FM.book Page 51 Tuesday, April 23, 2002 6:23 PM Copy Functions ❖ 1 Sided → Magazine Copies two or more originals to make page ordered copies when they are folded and stacked.
MartiniC1_GBcopy4_FM.book Page 52 Tuesday, April 23, 2002 6:23 PM Copying ❖ Open to Right • Open to Right 5 7 3 5 1 3 1 2 GCBOOK6E How to fold copies to make a booklet Fold the copy so that a crease is in the center and open as shown in the following illustration: 1 Reference Related Initial Settings 2 3 3 1 Note ❒ You cannot use the bypass tray with these functions. ❒ The machine automatically selects the reproduction ratio automatically to the paper size. ⇒ p.
MartiniC1_GBcopy4_FM.book Page 53 Tuesday, April 23, 2002 6:23 PM Copy Functions H Place your originals, and then press the {Start} } key. Note ❒ When placing individual originals on the exposure glass or in the document feeder in Batch mode, press the {#} } key after all are scanned. ❖ Original: A5K K/Copy paper: A4L L L/Copy paper A4K K or Original: A5L 2 repeats (100%) The original image is copied repeatedly.
MartiniC1_GBcopy4_FM.book Page 54 Tuesday, April 23, 2002 6:23 PM Copying Double Copies One original image is copied twice onto one copy, as shown in the illustration. ❒ Originals of size A5L and B6KL (51/2" × 81/2"L) cannot be detected properly on the exposure glass. Be sure to select such copy paper manually, or set the originals in the document feeder. Reference Related Initial Settings 2 ⇒ p.102 “Double Copies Separation Line” A Press the [Edit/Stamp] key.
MartiniC1_GBcopy4_FM.book Page 55 Tuesday, April 23, 2002 6:23 PM Copy Functions Centering You can make copies with the image moved to the center of the paper. A Select the paper. B Press the [Edit/Stamp] key. 2 Note ❒ You cannot use the bypass tray with this function. ❒ Original sizes and directions for centering are listed below. C Press the [Edit Image] key. D Press the [Centring] key. E Press the [OK] key. F Press the [OK] key. G Place your originals, and press the {Start} } key.
MartiniC1_GBcopy4_FM.book Page 56 Tuesday, April 23, 2002 6:23 PM Copying Note ❒ You can move the scanned position up to 30 mm (in 1mm steps) upward, downward, to left and to right. E Set the scanned position for the back of the original. Press the [↑ ↑] or [↓ ↓] key to set the top or bottom position. Press the [← ←] or [→ →] key to set the left or right position. Then press the [OK] key. 1 2 4 2 3 1. Top: 0 – 30 mm, 0" – 1.2" 2. Right: 0 – 30 mm, 0" – 1.2" 3. Bottom: 0 – 30 mm, 0" – 1.2" 4.
MartiniC1_GBcopy4_FM.book Page 57 Tuesday, April 23, 2002 6:23 PM Copy Functions ❖ Center This mode erases center margin of the original image. Reference The erase width in the Border, Ce nt er and C en te r/ Bo r d er modes is set to 10 mm (0.4”) at default settings. You can change this settings w ith the User Tools. ⇒ p.101 “Erase Center Width”, ⇒ p.
MartiniC1_GBcopy4_FM.book Page 58 Tuesday, April 23, 2002 6:23 PM Copying Selecting [Same Width] A Press the [Same Width] key. F Set the border to be erased from of the back. Note ❒ Erasing the border of the back is valid only when you copy 2-sided originals. G Press the [OK] key. H Place your originals, 2 press the {Start} } key. B Set an erase border width with the [n n] and [o o] keys. Note ❒ To change the value entered, press the [n n] and [o o] keys to set the new value. C Press the [OK] key.
MartiniC1_GBcopy4_FM.book Page 59 Tuesday, April 23, 2002 6:23 PM Copy Functions H Press the [OK] key. I Place your originals, press the {Start} } key. Selecting [Diff. Width] and then A Press the [Diff. Width] key. Center/Border Erase A Press the [Edit/Stamp] key. 2 B Press the key for the part you wish to change, and then set an erase margin width with the [n n] and [o o] keys. C Press the [OK] key. B Press the [Erase] key. C Press the [Erase Center/Border] key. D Press the [Center/Border] key.
MartiniC1_GBcopy4_FM.book Page 60 Tuesday, April 23, 2002 6:23 PM Copying Inside Erase I Press the [2-sided Setting] key and the [Back Side] key. A Decide where the machine starts Note ❒ If you don't need to erase the image on the back, go to step K. scanning (X1, Y1) and where it stops scanning (X2, Y2). Note ❒ You can input lengths of 0 – 432 mm, 0 – 17". 2 B J Enter the values of [X1], [Y1], [X2] and [Y2] for the back.
MartiniC1_GBcopy4_FM.book Page 61 Tuesday, April 23, 2002 6:23 PM Copy Functions E Enter the value of [X1] with the number keys, and then press the [#] key. 3 Edges Full Bleed You can make full image copy by cutting down the margin of top, bottom, and right sides. This function is useful for originals full of image. 2 F Enter the value of [Y1] with the number keys, and then press the [#] key. G Enter the value of [X2] with the number keys, and then press the [#] key.
MartiniC1_GBcopy4_FM.book Page 62 Tuesday, April 23, 2002 6:23 PM Copying A Press the [Edit/Stamp] key. Margin Adjustment You can shift the image to the left, right, top or bottom to make a binding margin. 2 A A B Press the [Erase/Margin Adj.] key. C Press the [Margin Adjustment] key. D Set a binding margin for a front Reference Related Initial Settings ⇒ p.101 “Front Margin : Left/Right” ⇒ p.101 “Back Margins : Left/Right” ⇒ p.101 “Front Margin : Top/Bottom” ⇒ p.101 “Back Margin : Top/Bottom” ⇒ p.
MartiniC1_GBcopy4_FM.book Page 63 Tuesday, April 23, 2002 6:23 PM Copy Functions Background Numbering Use this function to have numbers printed on the background of copies. G Press the [OK] key. H Set your originals, then press the {Start} } key. Preset Stamp 2 Messages you use frequently can be stored in memory and stamped on copies. GCSTMP2E Reference Related Initial Settings ⇒ p.104 “Size” and “Density” in “Background Numbering”. A Press the [Edit/Stamp] key.
MartiniC1_GBcopy4_FM.book Page 64 Tuesday, April 23, 2002 6:23 PM Copying Stamp Position and Original Direction C Press the [Preset Stamp] key. D Select the desired message. E Press the [All Pages] or [1st Page only] key to select the print page. Note ❒ You can change the position, size, and density of the stamp. ⇒ p.64 “Changing stamp position, size and density” 2 F After you specify all the desired settings, press the [OK] key. G Press the [OK] key. H Place your originals, press the {Start} } key.
MartiniC1_GBcopy4_FM.book Page 65 Tuesday, April 23, 2002 6:23 PM Copy Functions User Stamp Reference Related Initial Settings Copies with the registered stamp. ⇒ p.104 “Stamp Position” ⇒ p.104 “Stamp Format” A Press the [Edit/Stamp] key. 2 Preparation Before using this function, you have to program a user stamp. ⇒ p.66 “To program the user stamp” Stamp position and original orientation B Press the [Stamp] key. C Press the [User Stamp] key. D Select the stamp you require.
MartiniC1_GBcopy4_FM.book Page 66 Tuesday, April 23, 2002 6:23 PM Copying T h e m ai n m e n u o f t h e C o p ier/Document Server features appears. To change the stamp position A Press the [Change] key. B Select the desired position, and then press the [OK] key. 2 To program the user stamp D Press the [Stamp] key. E Press the [User Stamp] key. F Press the [Program/Delete Stamp] key. Note ❒ The range of stamp images for readability is 10 – 297 mm high (0.4" – 11.7") and 10 – 432 mm (0.
MartiniC1_GBcopy4_FM.book Page 67 Tuesday, April 23, 2002 6:23 PM Copy Functions Note ❒ Originals cannot be scanned from the document feeder when programming the user stamp. L Press the [Exit] key. M Press the [Exit] key. E Press the [User Stamp] key. F Press the [Program/Delete Stamp] key. G Press the [Delete] key, then press the stamp number (1–4) you want to delete. The display returns to the main menu of the Copier/Document Server features. N Press the [Exit] key.
MartiniC1_GBcopy4_FM.book Page 68 Tuesday, April 23, 2002 6:23 PM Copying Stamp position and original orientation B Press the [Stamp] key. C Press the [Date Stamp] key. D Press the [All Pages] or [1st Page only] key to select the print page. 2 Note ❒ You can change the font and position of the date to be stamped. ⇒ p.68 “To change the date format” GCSTMP7E Note ❒ You cannot use the bypass tray with this function. Reference Related Initial Settings ⇒ p.105 “Font” ⇒ p.105 “Size” ⇒ p.
MartiniC1_GBcopy4_FM.book Page 69 Tuesday, April 23, 2002 6:23 PM Copy Functions To change the stamp position A Press the left bottom [Change] key. Stamp position and orientation of originals 2 B Select the desired Date Stamp position, and then press the [OK] key. Page Numbering Use this function to print page numbers on your copies. GCSTMP8E Note ❒ You cannot use the bypass tray with this function.
MartiniC1_GBcopy4_FM.book Page 70 Tuesday, April 23, 2002 6:23 PM Copying A Press the [Edit/Stamp] key. Changing the stamp position A Press the left bottom [Change] key. 2 B Press the [Stamp] key. C Press the [Page Numbering] key. D Select the format. B Select the desired position, and then press the [OK] key. Specify the first printing page and start number If you selected (P1,P2…, -1-,-2-…, P.1, P.2…, 1, 2…, ) Note ❒ You can specify the stamp position, pages to be stamped, and numbering. ⇒ p.
MartiniC1_GBcopy4_FM.book Page 71 Tuesday, April 23, 2002 6:23 PM Copy Functions C Press the {#}} key. D Press the [Numbering from/to] key, and then use the number keys to enter the number to start numbering from, then press the {#} } key. B Press the [First Printing Page] key, and then use the number keys to enter the original sheet number to start numbering from. Note ❒ The following gives an example based on when the first printing page is “2” and the first page number is “3”.
MartiniC1_GBcopy4_FM.book Page 72 Tuesday, April 23, 2002 6:23 PM Copying F Press the [Total Pages] key, and then use the number keys to enter the total number of original pages, then press the {#} } key. G Press the [OK] key. Note ❒ To change settings after pressing the [OK] key, press the right bottom [Change] key, and then enter the numbers again. 2 If you selected (1–1, 1–2,…) A Press the right bottom [Change] key.
MartiniC1_GBcopy4_FM.book Page 73 Tuesday, April 23, 2002 6:23 PM Copy Functions A Press the [Cover/Slip Sheet] key. • Copy 1 2 3 1 2 3 2 • Blank B Press the (["Front Cover"] / [Front/Back Cover]) key. 1 2 3 1 2 3 C Select [Copy] or [Blank] for the cover sheet. ❖ Front/Back Covers The first and last pages of your original are copied on separate paper for cover use. • Copy D Select the paper tray containing non-cover sheet paper, and then press the [OK] key.
MartiniC1_GBcopy4_FM.book Page 74 Tuesday, April 23, 2002 6:23 PM Copying Note ❒ The paper for slip sheets should be the same size as the copy paper and should be set in the same direction. ❒ If you have selected "Interposer" for "Slip Sheet 2 Tray" in System Settings, you cannot copy on the slip sheets if you select "Slip Sheet 2". ❒ You cannot select the bypass tray for sheet paper to copy the originals. ❒ You can specify up to 20 pages. 2 A Press the [Cover/Slip Sheet] key.
MartiniC1_GBcopy4_FM.book Page 75 Tuesday, April 23, 2002 6:23 PM Copy Functions A Press the [Cover/Slip Sheet] key. Blank Slip Sheets You can insert a blank slip sheet (or sheets) before or after a specified page. 2 B Press the [Desig./Chapter] key. C Press the key to select a chapter 1 1 5 5 9 9 number. D Press the [Chapter] key. E Enter the number of the first page Preparation Before using this function, select a tray for slip sheets.
MartiniC1_GBcopy4_FM.book Page 76 Tuesday, April 23, 2002 6:23 PM Copying C Press the key to select the chapter number. D Press the [Insert Sheet] key. E Select the paper tray for slip sheets. F Select [Before] to insert slip sheets 2 before the page you specify. Select [After] to insert slip sheets after the page you specify. Enter the page number with the number keys. G Press the [Insert Quantity] key, and enter the number of sheets you wish to insert with the number keys.
MartiniC1_GBcopy4_FM.book Page 77 Tuesday, April 23, 2002 6:23 PM Copy Functions • Blank 2 1 12 2 Note ❒ OHP ship sheet(s) cannot be copied when using the interposer. A Press the [Cover/Slip Sheet] key. B Press the [Slip Sheet] key. C Select [Copy] or [Blank], and then press the [OK] key. D Select the paper tray that contains paper for copying originals. E Place originals, and then press the {Start} } key.
MartiniC1_GBcopy4_FM.book Page 78 Tuesday, April 23, 2002 6:23 PM Copying Storing Originals in the Document Server The Document Server enables you to save documents in memory and print them as required. B Enter a file name, user name, or password if neccessary. Important ❒ Data stored in the machine might be lost if some kind of failure occurs. The supplier shall not be responsible for any damage that might result from loss of data.
MartiniC1_GBcopy4_FM.book Page 79 Tuesday, April 23, 2002 6:23 PM 3. Program Programs You can store frequently used copy job settings in memory and recall them for future use. Note ❒ You can store up to 10 programs. ❒ You can select standard mode or program No. 10 as the mode to be set when modes are cleared or reset, or immediately after the operation switch is turned on. ⇒ p.99 “Change Initial Mode” ❒ Paper settings are stored based on size.
MartiniC1_GBcopy4_FM.book Page 80 Tuesday, April 23, 2002 6:23 PM Program E Enter the program name with the letter keys on the display panel. You can enter up to 40 characters. C Press the [Register] key. Repeat steps E, F of ”Storing a Program”. Note ❒ This overwrites the previous program. Deleting a Program 3 Reference For details on entering characters, see “Entering Text Characters” in the General Settings Guide. A Press the {Program}} key. B Press the [Delete] key.
MartiniC1_GBcopy4_FM.book Page 81 Tuesday, April 23, 2002 6:23 PM Programs C Press the program number you want to recall. Stored settings are displayed. Note ❒ Only programs with m against them contain a program. D Place your originals, and then press the {Start} } key.
MartiniC1_GBcopy4_FM.
MartiniC1_GBcopy4_FM.book Page 83 Tuesday, April 23, 2002 6:23 PM 4. Troubleshooting If Your Machine Does Not Operate as You Want When a Message is Displayed The following chart contains explanations of common messages. If other messages appear, follow the instructions as they are displayed. Messege Cause Action Cannot detect original size. The size of the originals Place the original on the exposure placed is difficult to detect. glass. ⇒ p.13 “Placing Originals on ⇒ p.
MartiniC1_GBcopy4_FM.book Page 84 Tuesday, April 23, 2002 6:23 PM Troubleshooting If You Cannot Make Clear Copies Problem Cause Action Copies appear dirty. The image density is too dark. Adjust the copy density. ⇒ p.25 “Adjusting Copy Image Density” Auto Image Density is not selected. Adjust the auto density. ⇒ p.25 “Adjusting Copy Image Density” The reverse side of an orig- The image density is too inal image is copied. dark. A shadow appears on copies if you use pasted originals.
MartiniC1_GBcopy4_FM.book Page 85 Tuesday, April 23, 2002 6:23 PM If You Cannot Make Copies As You Want If You Cannot Make Copies As You Want This section explains causes and remedies when copy results are not as expected. Problem Cause Action Copies are not stapled. There are jammed staples in the stapler. Remove jammed staples.
MartiniC1_GBcopy4_FM.book Page 86 Tuesday, April 23, 2002 6:23 PM Troubleshooting Problem Cause Action In Image Repeat mode, the original image is not copied repeatedly. You selected copy paper the same size as the originals, or you did not select the proper reproduction ratio. Select copy paper larger than the originals. The stamp position is wrong. The paper orientation is wrong. Check the paper orientation and stamp position. When using Combine, parts of the image are not copied.
MartiniC1_GBcopy4_FM.book Page 87 Tuesday, April 23, 2002 6:23 PM If You Cannot Make Copies As You Want When Memory Is Full Note ❒ If you set "Memory Full Auto Scan Restart" in User Tools (⇒ p.106) to "Yes", the memory overflow message will not be displayed, but Connect Copy continues to scan originals automatically. Connect Copy continues scanning and copying until the job is finished. Note that copy sets will be printed separately at this time. Message Cause Solution & Reference Memory is full.
MartiniC1_GBcopy4_FM.
MartiniC1_GBcopy4_FM.book Page 89 Tuesday, April 23, 2002 6:23 PM 5. User Tools (Copy/Document Server Features) User Tools Menu (Copier/Document Server Features) User Tools Item Names Default Settings General Features 1/5 ⇒ p.
MartiniC1_GBcopy4_FM.book Page 90 Tuesday, April 23, 2002 6:23 PM User Tools (Copy/Document Server Features) User Tools Item Names Default Settings Copy Function Key: F1–F5 • F1: 1 Sided → 2 Sided: T to T • F2: 2 Sided: T to T → 2 Sided: T to T • F3: 1 Sided → 1 Sided Combine • F4: 1 Sided → 1 Sided Combine: 4 originals • F5: Create Margin General Features 4/5 ⇒ p.
MartiniC1_GBcopy4_FM.book Page 91 Tuesday, April 23, 2002 6:23 PM User Tools Menu (Copier/Document Server Features) User Tools Item Names Default Settings Enlarge 1–5 Metric version • Enlarge 1: 115% • Enlarge 2: 122% • Enlarge 3: 141% • Enlarge 4: 200% • Enlarge 5: 400% Inch version • Enlarge 1: 121% • Enlarge 2: 129% • Enlarge 3: 155% • Enlarge 4: 200% • Enlarge 5: 400% Priority Setting: Enlarge Metric version 141% Inch version 155% 5 Reproduction Ratio 2/2 ⇒ p.
MartiniC1_GBcopy4_FM.book Page 92 Tuesday, April 23, 2002 6:23 PM User Tools (Copy/Document Server Features) User Tools Item Names Default Settings Back Margin: Top/Bottom Metric version: T/B 0 mm Inch version: T/B 0” 1 Sided → 2 Sided Auto Margin: T to T Metric version: Right 5 mm 1 Sided → 2 Sided Auto Margin: T to B Metric version: T/B 0 mm Inch version: Right 0.2” Inch version: T/B 0” Erase Border Width Metric version: 10 mm Inch version: 0.
MartiniC1_GBcopy4_FM.book Page 93 Tuesday, April 23, 2002 6:23 PM User Tools Menu (Copier/Document Server Features) User Tools Item Names User Stamp Default Settings Program/Delete Stamp Stamp Position: 1~4 Metric version • Position: Top right • Top Margin: 24 mm • Right Margin: 24 mm Inch version • Position: Top right • Top Margin: 1.0" • Right Margin: 1.
MartiniC1_GBcopy4_FM.book Page 94 Tuesday, April 23, 2002 6:23 PM User Tools (Copy/Document Server Features) User Tools Item Names Page Numbering Default Settings Stamp Format P1, P2... Font Font 1 Size Auto Duplex Back Page Stamping Position Opposite position Page Numbering in Combine Per original Stamp on Designated Slip Sheet Stamp Position No Metric version • Position P1, 1/5, P.1, 1: Top right -1-, 1–1: Bottom center • Top/Bottom Margin P1, 1/5, P.
MartiniC1_GBcopy4_FM.book Page 95 Tuesday, April 23, 2002 6:23 PM User Tools Menu (Copier/Document Server Features) User Tools Item Names Default Settings Select Stapling Position (Top Right) Top 2 Select Stapling Position (Bottom Right) Left 2 Input/Output 2/2 ⇒ p.
MartiniC1_GBcopy4_FM.book Page 96 Tuesday, April 23, 2002 6:23 PM User Tools (Copy/Document Server Features) Accessing User Tools (Copy/Document Server Features) This section is for key operators in charge of this machine. You can change default settings. Note ❒ Be sure to exit from User Tools after all settings are finished. ❒ Selected keys are highlighted.
MartiniC1_GBcopy4_FM.book Page 97 Tuesday, April 23, 2002 6:23 PM Accessing User Tools (Copy/Document Server Features) General Features 1/5 ❖ Auto Paper Select Priority You can choose to have“Auto Paper Select” selected when the machine is turned on or reset, or modes are cleared. ⇒ p.27 “Selecting Copy Paper” ❖ Auto Tray Switching If you load paper of the same size in two or more trays, the machine automatically shifts to the other tray when the tray in use runs out (when Auto Paper Select is selected.
MartiniC1_GBcopy4_FM.book Page 98 Tuesday, April 23, 2002 6:23 PM User Tools (Copy/Document Server Features) ❖ Paper Display You can choose to have available paper trays/sizes shown on the initial display. Note ❒ If you choose "Hide", the display is shown as below. When the [Auto Paper Select] key is pressed, paper sizes appear on the display. 5 ❖ Original Type Priority You can select the type of originals effective when the machine is turned on or reset, or when modes are cleared.
MartiniC1_GBcopy4_FM.book Page 99 Tuesday, April 23, 2002 6:23 PM Accessing User Tools (Copy/Document Server Features) General Features 2/5 ❖ Duplex Mode Priority You can select the type of Duplex function effective when the machine is turned on or reset, or when modes are cleared. ❖ Copy Orientation in Duplex Mode You can set copy orientation when making two-sided copies. ❖ Original Orientation in Duplex Mode You can set original orientation when making two-sided copies.
MartiniC1_GBcopy4_FM.book Page 100 Tuesday, April 23, 2002 6:23 PM User Tools (Copy/Document Server Features) General Features 5/5 Reproduction Ratio 2/2 ❖ Document Server Print Key: F1–F5 You can register frequently used functions in function keys F1 to F5. You can also change registered functions. ❖ Reduce 1–6 You can customize available reduction ratios when you press the [Reduce/Enlarge] key followed by the [Reduce] key.
MartiniC1_GBcopy4_FM.book Page 101 Tuesday, April 23, 2002 6:23 PM Accessing User Tools (Copy/Document Server Features) Edit 1/2 ❖ Front Margin : Left/Right You can specify left and right margins on the front side of copies in Margin Adjust mode. Note ❒ You can enter a margin width of between 0 and 30 mm in 1 mm increments (0” and 1.2” in 0.1” steps) with the number keys. ❖ Back Margins : Left/Right You can specify left and right margins on the back side of copies in Margin Adjust mode.
MartiniC1_GBcopy4_FM.book Page 102 Tuesday, April 23, 2002 6:23 PM User Tools (Copy/Document Server Features) Edit 2/2 ❖ Image Repeat Separation Line You can select a separation line in Image Repeat mode: None, Solid, Broken A, Broken B or Crop Marks. • None ❖ Double Copies Separation Line You can select a separation line in Double Copy mode: None, Solid, B ro k e n A , B r o k e n B o r C r o p Marks.
MartiniC1_GBcopy4_FM.book Page 103 Tuesday, April 23, 2002 6:23 PM Accessing User Tools (Copy/Document Server Features) ❖ Separation Line in Combine You can select a separation line in Combine mode: None, Solid, Broken A, Broken B or Crop Marks. ⇒ p.45 “1 Sided Combine”, ⇒ p.47 “2 Sided Combine” • None ❖ Front Cover Copy in Combine You can make a combined copy on the front cover sheet when you select Front Cover copy mode.
MartiniC1_GBcopy4_FM.book Page 104 Tuesday, April 23, 2002 6:23 PM User Tools (Copy/Document Server Features) Stamp Background Numbering ❖ Size You can set the size of the numbers. ❖ Density You can set the density of the numbers. User Stamp 1/2-2/2 Preset Stamp 1/4-4/4 ❖ Program/Delete Stamp You can register/change/delete designs you like as user stamps. ❖ Stamp Priority You can select the priority stamp type when the [Preset Stamp] key is pressed. ⇒ p.
MartiniC1_GBcopy4_FM.book Page 105 Tuesday, April 23, 2002 6:23 PM Accessing User Tools (Copy/Document Server Features) Date Stamp ❖ Format You can select the date format for Date Stamp mode. ❖ Font You can select the Date Stamp font. ❖ Stamp Position You can set the position at which the stamp is printed. Press the arrow keys to adjust the position. ❖ Stamp Setting You can select whether the date is printed on the first page or all pages. ❖ Size You can set the Date Stamp size.
MartiniC1_GBcopy4_FM.book Page 106 Tuesday, April 23, 2002 6:23 PM User Tools (Copy/Document Server Features) Input/Output 1/2 ❖ Switch to Batch (SADF) You can have Batch mode or SADF mode have displayed when you press the Special Original key. ⇒ p.14 “Batch mode” ❖ SADF Auto Reset When you set one original at a time in the document feeder, the Auto Feed indicator lights for a selected time after an original is fed, to show is ready for another original.
MartiniC1_GBcopy4_FM.book Page 107 Tuesday, April 23, 2002 6:23 PM Accessing User Tools (Copy/Document Server Features) ❖ Select Stapling Position (Bottom Left) You can register a type of stapling used frequently in the bottom left staple key on the initial display. You can also change the registered type. Note ❒ The Finisher 3000B(100–sheet staples), Finisher 3000M(50– sheet staples) or Booklet Finisher is required to use this function.
MartiniC1_GBcopy4_FM.book Page 108 Tuesday, April 23, 2002 6:23 PM User Tools (Copy/Document Server Features) ❖ Letterhead Setting If you select "Yes" in this function, the machine rotates the image correctly. Note ❒ Direction-fixed (top to bottom) or 2-sided paper might not be printed correctly depending on how the originals and paper are placed. Reference When using letterhead paper, pay attention to the paper orientation. ⇒ p.
MartiniC1_GBcopy4_FM.book Page 109 Tuesday, April 23, 2002 6:23 PM 6. Specifications Combination Chart The combination chart given below shows modes that can be used together. When using the chart, note the explanations of the symbols, as given in the following table. ❍ These modes can be used together. $ These modes cannot be used together. The second mode selected will be the mode you're working in. × These modes cannot be used together. The first mode selected will be the mode you're working in.
MartiniC1_GBcopy4_FM.
MartiniC1_GBcopy4_FM.book Page 111 Tuesday, April 23, 2002 6:23 PM Supplementary Specifications Supplementary Specifications ❖ Batch Mode In Batch mode, you cannot switch between 1–sided originals and 2–sided originals in the middle of copying. ❖ Mixed Size mode • Copy speed and scanning speed may be reduced.
MartiniC1_GBcopy4_FM.
MartiniC1_GBcopy4_FM.book Page 113 Tuesday, April 23, 2002 6:23 PM Supplementary Specifications ❖ Auto Reduce/Enlarge • The reproduction ratios you can specify are 25 – 400%. ❖ Size Magnification • If the calculated ratio is over maximum or under the minimum ratio, it is adjusted to within available range automatically. However, with some ratios, parts of the image might not be copied or margins will appear on. • The reproduction ratio that you can specify are 25 – 400%.
MartiniC1_GBcopy4_FM.book Page 114 Tuesday, April 23, 2002 6:23 PM Specifications Paper Size and Direction Number of Copies Finisher Upper Tray 500 sheets (80 g/m2) (20 lb.) Finisher 3000B(100– sheet staples) A4KL, B5KL, A5KL, B6L, A6L, 81/2" × 11"KL, 51/2" × 81/2"KL 6 A3L, B4L, 11" × 17"L, 81/2" × 14"L, 12" × 18"L 250 sheets (80 g/m2) (20 lb.) Finisher Shift Tray 3, 000 sheets (80 g/m2) (20 lb.
MartiniC1_GBcopy4_FM.book Page 115 Tuesday, April 23, 2002 6:23 PM Supplementary Specifications Paper Size and Direction Number of Copies Finisher Upper tray 250 sheets (80 g/m2) (20 lb.) A4KL, B5KL, A5KL, B6KL, 81/2" × 11"KL, 51/2" × 81/2"KL A3L, B4L, 11" × 17"L, 81/2" × 14"L, 12" × 18"L 50 sheets (80 g/m2) (20 lb.) Finisher shift tray 1 500 sheets (80 g/m2) (20 lb.) Booklet Finisher A4KL, B5KL, A5K, 81/2" × 11"KL A3L, B4L, 11" × 17"L, 81/2" × 14"L, 12" × 18"L 250 sheets (80 g/m2) (20 lb.
MartiniC1_GBcopy4_FM.
MartiniC1_GBcopy4_FM.book Page 117 Tuesday, April 23, 2002 6:23 PM Supplementary Specifications • When using "Left 2" or "Top 2" with Double copies, or "1 Sided → 1 Sided", "1 Sided → 2 Sided", "2 Sided → 1 Sided", or "2 Sided → 2 Sided" in Combine mode, select K original for L copy and L originals for K copy. • If you use the Auto Paper Select function in the Mixed Size mode, the machine selects the proper size of paper and staples it even if you place different sizes of originals.
MartiniC1_GBcopy4_FM.
MartiniC1_GBcopy4_FM.book Page 119 Tuesday, April 23, 2002 6:23 PM Supplementary Specifications Paper Sizes and Orientation Saddle Stitch A4L, 81/2" × 11"L Other paper size Maximum Number of the Sheets Maximum Number of the Stapled Copies 2∼5 sheets 25 sets 6∼10 sheets 15 sets 11∼15 sheets 10 sets 2∼5 sheets 30 sets 6∼10 sheets 20 sets 11∼15 sheets 10 sets You cannot change the stapling positions during copying. When the original image is rotated, the stapling direction turns by 90°.
MartiniC1_GBcopy4_FM.
MartiniC1_GBcopy4_FM.book Page 121 Tuesday, April 23, 2002 6:23 PM Supplementary Specifications • If the number of originals placed is less than the number specified for combining, the last page is left blank, as shown in the illustration. ❖ Copying Book Originals • The machine sets the reproduction ratio automatically to meet paper size and copies originals together onto the paper.
MartiniC1_GBcopy4_FM.book Page 122 Tuesday, April 23, 2002 6:23 PM Specifications ❖ Centering Although the original is set at a different orientation to the paper, the machine will not rotate the image by 90° (Rotate copy). ❖ Erase The width of the erased margin varies depending on the reproduction ratio. If the size of the original is different to sizes listed in the following chart, the erased margin might be shifted.
MartiniC1_GBcopy4_FM.
MartiniC1_GBcopy4_FM.book Page 124 Tuesday, April 23, 2002 6:23 PM Specifications If you combine this function with the Duplex (Top to Top) function and select the "P1, P2" or "1/n, 2/n" format, the page numbers on the back of are printed as follows: 1 2 GCSTMPBE 1. Front 2.
MartiniC1_GBcopy4_FM.
MartiniC1_GBcopy4_FM.
MartiniC1_GBcopy4_FM.
MartiniC1_GBcopy4_FM.
MartiniC1_GBcopy4_FM.
MartiniC1_GBcopy4_FM.
