User manual
Table Of Contents
- GX5050 User Guide
- J011 User Guide
- Table of Contents
- Read This First
- Paper
- Replacing Consumables
- Making Printer Settings
- Troubleshooting
- Printing Will Not Start
- Paper Is Not Fed or Delivered Normally
- Paper Jam
- Removing Paper Jammed in the Paper Tray (Tray 1)
- Removing Paper Jammed in the Optional Tray (Tray 2 (Optional))
- Removing Paper Jammed in the Bypass Tray (optional)
- Removing Paper Jammed under the Top Cover
- Removing Paper Jammed around the Guide Board
- Removing Paper Jammed in the Duplex Unit
- Removing Paper Jammed in the Output Tray
- Print Results Are Not Satisfactory
- Error & Status Messages on the Control Panel
- Status Monitor Errors
- Status Monitor Does Not Open
- No Response from Printer
- No Paper/Tray Not Detected (Tray 1)
- No Paper/Tray Not Detected (Tray 2)
- No Paper/Tray Not Detected (Bypass Tray)
- Paper Size Mismatch/Paper Type Mismatch (Tray 1)
- Paper Size Mismatch/Paper Type Mismatch (Tray 2)
- Paper Size Mismatch/Paper Type Mismatch (Bypass Tray)
- Paper Size Mismatch/Paper Type Mismatch (AutoTray Select)
- Cover Open
- Duplex Unit Not Detected
- Cover Open / Print Cartridge(s) Not Detected
- Cartridge End
- Cartridge/Print-head Tank Empty
- When the Ink Collector Unit is Almost Full/Full
- Ink Collector Unit Not Detected
- Out of Printable Temperature Range
- Printer Error
- Network Interface Board Error
- Adjusting the Printer
- Inquiries and Consumables
- Maintaining
- Preparing for Printing
- Confirming the Connection Method
- Installing the Printer Driver (USB)
- Sharing the Printer
- Using the SmartDeviceMonitor for Client Port
- Using the Standard TCP/IP Port
- Using the LPR Port
- Using as the Windows Network Printer
- Using as the NetWare Print Server/Remote Printer
- If a Message Appears during Installation
- Making Option Settings for the Printer
- Printer Driver
- Printing
- Printing on Various Paper Types
- Canceling Printing
- Adjusting Print Quality
- Various Print Functions
- Printing Multiple Document Sets
- Collating
- Printing Web Pages
- Reducing and Enlarging to Fit the Paper Size (Fit to paper size)
- Reducing and Enlarging by a Specified Ratio (Scale, Directional magnification)
- Reducing to A4/Letter Automatically
- Rotating the Image by 180 Degrees
- Printing on Registered Custom Size Paper
- Printing on Unregistered Custom Size Paper
- Printing on Both Sides of Paper
- Printing Multiple Document Pages per Sheet (Layout)
- Splitting the Document Image across Multiple Sheets (Poster)
- Printing from the Last Page
- Creating a Binding Margin
- Printing Documents with a Header and Footer
- Printing with a Layout Suitable for Making Booklets
- Printing Images or Text Superimposed on Prints
- Printing Documents with an Overlay Image Superimposed (Overlay)
- Unauthorized Copy Control
- Displaying the Preview before Printing
- Custom Settings
- Supporting Multi-Languages
- Monitoring and Configuring the Printer
- Using a Printer Server
- Additional Information
- J011 Notes for Users
- J011 User Guide
109
Troubleshooting
Reset Cartridge
No print cartridge has been installed. Install the print cartridge correctly.
See p.126 "
Cover Open / Print Cartridge(s) Not Detected".
Dry Waiting...
The ink on the printed OHP transparency is being allowed to dry.
Waiting...
Wait a moment.
Energy Saver
The printer is in Energy Saver mode. The printer is ready for use.
Cannot use High Temp./Power Off On
The temperature is abnormally high.
Switch the printer off and then on. If the message reappears, contact your service representative.
See p.131 "
Out of Printable Temperature Range".
Cannot use Low Temp./Power Off On
The temperature is abnormally low.
Switch the printer off and then on. If the message reappears, contact your service representative.
See p.131 "
Out of Printable Temperature Range".
Resetting Job...
The printer is reinitializing a print job.
Wait a moment.
Setting change
The printer is changing its settings. Wait a moment.
Load Paper:Tray# or Form Feed
The selected tray has run out of paper.
Reload the tray. Alternately, press the [Form Feed] key, select a different tray, and then print. To cancel the print
job, press the [Job Reset] key.
See p.112 "
No Paper/Tray Not Detected (Tray 1)", p.119 "Paper Size Mismatch/Paper Type Mismatch (Tray
2)", p.116 "No Paper/Tray Not Detected (Bypass Tray)".
Change Setting Tray #/
The size of paper in the selected tray does not match the specified paper size.
Load the tray with paper of the specified size, and then change the paper size setting for the tray on the control
panel. Alternately, press the [Form Feed] key, select a tray containing paper of the specified size, and then print.
To cancel the print job, press the [Job Reset] key.
See p.117 "
Paper Size Mismatch/Paper Type Mismatch (Tray 1)", p.119 "Paper Size Mismatch/Paper Type
Mismatch (Tray 2)", p.121 "Paper Size Mismatch/Paper Type Mismatch (Bypass Tray)".