User manual
Table Of Contents
- GX5050 User Guide
- J011 User Guide
- Table of Contents
- Read This First
- Paper
- Replacing Consumables
- Making Printer Settings
- Troubleshooting
- Printing Will Not Start
- Paper Is Not Fed or Delivered Normally
- Paper Jam
- Removing Paper Jammed in the Paper Tray (Tray 1)
- Removing Paper Jammed in the Optional Tray (Tray 2 (Optional))
- Removing Paper Jammed in the Bypass Tray (optional)
- Removing Paper Jammed under the Top Cover
- Removing Paper Jammed around the Guide Board
- Removing Paper Jammed in the Duplex Unit
- Removing Paper Jammed in the Output Tray
- Print Results Are Not Satisfactory
- Error & Status Messages on the Control Panel
- Status Monitor Errors
- Status Monitor Does Not Open
- No Response from Printer
- No Paper/Tray Not Detected (Tray 1)
- No Paper/Tray Not Detected (Tray 2)
- No Paper/Tray Not Detected (Bypass Tray)
- Paper Size Mismatch/Paper Type Mismatch (Tray 1)
- Paper Size Mismatch/Paper Type Mismatch (Tray 2)
- Paper Size Mismatch/Paper Type Mismatch (Bypass Tray)
- Paper Size Mismatch/Paper Type Mismatch (AutoTray Select)
- Cover Open
- Duplex Unit Not Detected
- Cover Open / Print Cartridge(s) Not Detected
- Cartridge End
- Cartridge/Print-head Tank Empty
- When the Ink Collector Unit is Almost Full/Full
- Ink Collector Unit Not Detected
- Out of Printable Temperature Range
- Printer Error
- Network Interface Board Error
- Adjusting the Printer
- Inquiries and Consumables
- Maintaining
- Preparing for Printing
- Confirming the Connection Method
- Installing the Printer Driver (USB)
- Sharing the Printer
- Using the SmartDeviceMonitor for Client Port
- Using the Standard TCP/IP Port
- Using the LPR Port
- Using as the Windows Network Printer
- Using as the NetWare Print Server/Remote Printer
- If a Message Appears during Installation
- Making Option Settings for the Printer
- Printer Driver
- Printing
- Printing on Various Paper Types
- Canceling Printing
- Adjusting Print Quality
- Various Print Functions
- Printing Multiple Document Sets
- Collating
- Printing Web Pages
- Reducing and Enlarging to Fit the Paper Size (Fit to paper size)
- Reducing and Enlarging by a Specified Ratio (Scale, Directional magnification)
- Reducing to A4/Letter Automatically
- Rotating the Image by 180 Degrees
- Printing on Registered Custom Size Paper
- Printing on Unregistered Custom Size Paper
- Printing on Both Sides of Paper
- Printing Multiple Document Pages per Sheet (Layout)
- Splitting the Document Image across Multiple Sheets (Poster)
- Printing from the Last Page
- Creating a Binding Margin
- Printing Documents with a Header and Footer
- Printing with a Layout Suitable for Making Booklets
- Printing Images or Text Superimposed on Prints
- Printing Documents with an Overlay Image Superimposed (Overlay)
- Unauthorized Copy Control
- Displaying the Preview before Printing
- Custom Settings
- Supporting Multi-Languages
- Monitoring and Configuring the Printer
- Using a Printer Server
- Additional Information
- J011 Notes for Users
- J011 User Guide
147
Preparing for Printing
Installing the Printer Driver (USB)
Follow the procedure below to install the printer driver only.
If you installed the printer driver when performing Quick Install for USB, there is no need to install it again here.
z
To install the printer driver under Windows 2000/XP or Windows Server 2003, you must log on as a user with administrator rights.
z
Do not turn on the power at this point.
The following explanation uses Windows 2000 as an example. Procedures under other operating systems may
differ.
Screens vary according to the operating environment.
1. Start Windows, and insert the provided "Drivers, Manual & Utility" CD-ROM into the CD-ROM
drive.
Quit all other applications currently running.
When you start Windows, the Add New Hardware Wizard may appear. If this happens, click [Cancel].
Check again that the power is off, and then proceed to step 2
.
After inserting the CD-ROM, the [Drivers, Manual & Utility] dialog box appears. If it does not, doubleclick
the CD-ROM drive icon under [My Computer] or [Explorer], and then double-click [SETUP.EXE].
If the [Drivers, Manual & Utility] screen does not appear even when you double-click the [SETUP.EXE] icon,
or if an error occurs during installation, access the CD-ROM drive from [My Computer] or [Explorer], dou-
ble-click the [English] icon, and then install the printer driver by following the instructions that appear on the
screen.
2. Click [PCL/RPCS Raster Printer Drivers].
3. Read the license agreement, click [I accept the agreement.], and then click [Next >].
4. Click [Next >].
5. Click [Connected with USB cable], and then click [Next >].
6. Check again that the power of the printer is off, and then click [Next >].
Check that the dialog box below appears.