User manual
Table Of Contents
- GX5050 User Guide
- J011 User Guide
- Table of Contents
- Read This First
- Paper
- Replacing Consumables
- Making Printer Settings
- Troubleshooting
- Printing Will Not Start
- Paper Is Not Fed or Delivered Normally
- Paper Jam
- Removing Paper Jammed in the Paper Tray (Tray 1)
- Removing Paper Jammed in the Optional Tray (Tray 2 (Optional))
- Removing Paper Jammed in the Bypass Tray (optional)
- Removing Paper Jammed under the Top Cover
- Removing Paper Jammed around the Guide Board
- Removing Paper Jammed in the Duplex Unit
- Removing Paper Jammed in the Output Tray
- Print Results Are Not Satisfactory
- Error & Status Messages on the Control Panel
- Status Monitor Errors
- Status Monitor Does Not Open
- No Response from Printer
- No Paper/Tray Not Detected (Tray 1)
- No Paper/Tray Not Detected (Tray 2)
- No Paper/Tray Not Detected (Bypass Tray)
- Paper Size Mismatch/Paper Type Mismatch (Tray 1)
- Paper Size Mismatch/Paper Type Mismatch (Tray 2)
- Paper Size Mismatch/Paper Type Mismatch (Bypass Tray)
- Paper Size Mismatch/Paper Type Mismatch (AutoTray Select)
- Cover Open
- Duplex Unit Not Detected
- Cover Open / Print Cartridge(s) Not Detected
- Cartridge End
- Cartridge/Print-head Tank Empty
- When the Ink Collector Unit is Almost Full/Full
- Ink Collector Unit Not Detected
- Out of Printable Temperature Range
- Printer Error
- Network Interface Board Error
- Adjusting the Printer
- Inquiries and Consumables
- Maintaining
- Preparing for Printing
- Confirming the Connection Method
- Installing the Printer Driver (USB)
- Sharing the Printer
- Using the SmartDeviceMonitor for Client Port
- Using the Standard TCP/IP Port
- Using the LPR Port
- Using as the Windows Network Printer
- Using as the NetWare Print Server/Remote Printer
- If a Message Appears during Installation
- Making Option Settings for the Printer
- Printer Driver
- Printing
- Printing on Various Paper Types
- Canceling Printing
- Adjusting Print Quality
- Various Print Functions
- Printing Multiple Document Sets
- Collating
- Printing Web Pages
- Reducing and Enlarging to Fit the Paper Size (Fit to paper size)
- Reducing and Enlarging by a Specified Ratio (Scale, Directional magnification)
- Reducing to A4/Letter Automatically
- Rotating the Image by 180 Degrees
- Printing on Registered Custom Size Paper
- Printing on Unregistered Custom Size Paper
- Printing on Both Sides of Paper
- Printing Multiple Document Pages per Sheet (Layout)
- Splitting the Document Image across Multiple Sheets (Poster)
- Printing from the Last Page
- Creating a Binding Margin
- Printing Documents with a Header and Footer
- Printing with a Layout Suitable for Making Booklets
- Printing Images or Text Superimposed on Prints
- Printing Documents with an Overlay Image Superimposed (Overlay)
- Unauthorized Copy Control
- Displaying the Preview before Printing
- Custom Settings
- Supporting Multi-Languages
- Monitoring and Configuring the Printer
- Using a Printer Server
- Additional Information
- J011 Notes for Users
- J011 User Guide
244
Using a Printer Server
Using NetWare
This section explains setting procedures for network printers in the NetWare environment. In the Netware envi-
ronment, you can connect the printer as a "print server" or as "remote printer". Network interface board supports
NetWare 5.1/6.5.
The network interface board is setup with a Web browser or with telnet.
Setting procedure with a Web browser is described here.
Setting Procedure
z
To use the printer as a print server
1. Configure the network interface board (by Web browser)
2. Turn the printer off and then back on
z
When using the printer as a remote printer
1. To use the network interface board (by Web browser)
2. Configure NetWare
3. Start the print server
Using Print Sever (NetWare 5.1, NetWare 6.5)
Follow the procedure below to connect the printer as a print server using NetWare 5.1/6.5.
z
To use the printer as a print server in NetWare 5.1/6.5, set it to the NDS mode.
z
To use NetWare 5.1/6.5, set the printer as a print server.
1. Launch the Web browser.
2. In the address bar, enter "http://(printer's IP address or host name)/".
Web browser top page is displayed.
If SSL encryption has been enabled, enter "https://(printer's address or host name)/".
3. 3. Click [Settings].
A dialog box for entering a user name and password appears.
4. Enter your user name and password, and then click [OK].
If this is the first time to do this, enter "admin" as the user name and leave the password blank.
Password " " (blank) is the factory default.
5. Change the password.
6. Click [NetWare Settings].
Setup items are as follows.
z
Netware: Set Netware to enable or disable.
z
IPX Protocol: Set IPX Protocol to enable or disable.
z
Network Frame Type: Select the frame type to be used.
z
Operation mode: Select whether the network interface board is to be used as a print server or as a
remote printer.