User's Manual
Table Of Contents
- PremierWave XC HSPA+ User Guide
- 1: Using This Guide
- 2: Introduction
- 3: Installation of PremierWave XC HSPA+
- 4: Using DeviceInstaller
- 5: Configuration Using Web Manager
- 6: Network Settings
- Network 1 (eth0) Interface Settings
- Network 1 (Link) Settings
- Network 1 (Failover)
- Network 2 (Cellular) Settings
- Network 2 (Link) Settings
- Gateway
- 7: Cellular
- 8: Action Settings
- 9: Line and Tunnel Settings
- Line Settings
- Tunnel Settings
- Serial Settings
- To Configure Tunnel Serial Settings
- Packing Mode
- To Configure Tunnel Packing Mode Settings
- Accept Mode
- To Configure Tunnel Accept Mode Settings
- Connect Mode
- To Configure Tunnel Connect Mode Settings
- Disconnect Mode
- To Configure Tunnel Disconnect Mode Settings
- Modem Emulation
- To Configure Tunnel Modem Emulation Settings
- Relay Output
- 10: Terminal and Host Settings
- 11: Services Settings
- 12: Security Settings
- 13: Maintenance and Diagnostics Settings
- Filesystem Settings
- Protocol Stack Settings
- SMTP Settings
- Diagnostics
- Threads
- Clock
- System Settings
- Discovery and Query Port
- 14: Advanced Settings
- 15: Security in Detail
- 16: Updating Firmware
- 17: Branding the PremierWave XC HSPA+
- Appendix A: Technical Specifications
- Appendix B: Compliance
- Appendix C: Technical Support
- Appendix D: Binary to Hexadecimal Conversions
- Appendix E: USB-CDC-ACM Device Driver File for Windows Hosts
4: Using DeviceInstaller
PremierWave XC HSPA+ User Guide 26
Group
Configurable field. Enter a group to categorize the . Double-click the field,
type in the value, and press Enter to complete. This group name is local to
this PC and is not visible on other PCs or laptops using DeviceInstaller.
Comments
Configurable field. Enter comments for the . Double-click the field, type in
the value, and press Enter to complete. This description or comment is local
to this PC and is not visible on other PCs or laptops using DeviceInstaller.
Device Family Shows the device family type as “PremierWave”.
Short Name Shows “premierwave_xc_hspa” by default.
Long Name Shows “Lantronix PremierWave XC HSPA+” by default.
Type Shows the device type as “PremierWave XC HSPA+””.
ID Shows the PremierWave ID embedded within the unit.
Hardware Address Shows the PremierWave hardware (MAC) address.
Firmware Version Shows the firmware currently installed on the PremierWave.
Extended Firmware Version Provides additional information on the firmware version.
Online Status Shows the PremierWave status as Online, Offline, Unreachable (the
PremierWave is on a different subnet), or Busy (the PremierWave is
currently performing a task).
IP Address Shows the PremierWave current IP address. To change the IP address,
click the Assign IP button on the DeviceInstaller menu bar.
IP Address was Obtained Appears “Dynamically” if the PremierWave automatically received an IP
address (e.g., from DHCP). Appears “Statically” if the IP address was
configured manually.
If the IP address was assigned dynamically, the following fields appear:
Obtain via DHCP with values of True or False.
Obtain via BOOTP with values of True or False.
Subnet Mask Shows the subnet mask specifying the network segment on which the
PremierWave resides.
Gateway Shows the IP address of the router of this network.
There is no default.
Number of Ports Shows the number of serial inputs.
Supports Configurable Pins Shows False, indicating configurable pins are not available on the
PremierWave.
Supports Email Triggers Shows True, indicating email triggers are available on the PremierWave.
Telnet Supported Indicates whether Telnet is enabled on this PremierWave.
Telnet Port Shows the PremierWave port for Telnet sessions.
Web Port Shows the PremierWave port for web sessions.
Firmware Upgradable
Shows True, indicating the PremierWave firmware is upgradable as newer
versions become available.
Current Settings Description
PRELIMINARY DRAFT
PRELIMINARY DRAFT