Data Sheet
Table Of Contents
- Table of Contents
- List of Figures
- List of Tables
- 1: Functional Description
- 2: Hardware and Software Description
- xPico 200 Block Diagram
- Software Features
- Network Co-Processor Mode
- Wireless Microcontroller Mode
- TruPort Serial
- TruPort Socket
- Ethernet to Wi-Fi Bridge
- Concurrent Soft AP and Client Mode
- Enterprise Wi-Fi Security (802.11i, 802.1X/EAP)
- InfiniShield Security
- Wi-Fi Connection Profiles
- Configuration and Management Interface
- Reliable Firmware Over-The-Air (FOTA) Updates
- Power Management
- Pre-integration with MACH10 Platform
- Remote Gateway Management with Lantronix Gateway Central
- Integrated Bluetooth Classic and Bluetooth Low Energy Stacks (xPico 250)
- 3: Pin and Pad Definitions
- Note1: The current module supports an external 10/100 Mbps Ethernet PHY via the RMII interface.
- Note2: The logic IO pins are 3.3V tolerant.
- Note3: SMT Pins 67 to 75 are the ground pads under the module. These pads must be connected to ground. These pads also provide thermal relief for the module. It is recommended that multiple vias for each pad be used to connect the ground pads to t...
- Note 4: All unused IO pins may be left floating, except for the required straps on pins 17, 26, and 29.
- Note 5: Asterisk (*) indicates feature available in a future release. Contact your local sales representative for availability.
- Signal
- Pin
- Signal
- Pin
- Driver Strength
- Edge Connector Pin
- xPico 200 SMT Pin
- Primary Function
- Signal Name
- 4: Interfaces
- Edge Conn. Pin
- SMT Pin
- Description
- Pin Name
- Type A USB Host Conn. Pin
- Signal Requirement
- Edge Conn. Pin
- SMT Pin
- Description
- Pin Name
- Edge Conn. Pin
- SMT Pin
- Description
- Pin Name
- Edge Conn. Pin
- SMT Pin
- Description
- Pin Name
- Edge Connector Pin
- xPico 200 SMT Pin
- Reset State
- Description
- Pin Name
- Edge Connector Pin
- xPico 200 SMT Pin
- Description
- Pin Name
- 5: IEEE 802.11 Wireless Lan Specifications
- Description
- Feature
- China
- Japan
- New Zealand
- Australia
- Europe
- Canada
- FCC/USA
- Channel
- Frequency
- China
- Japan
- New Zealand
- Australia
- Europe
- Canada
- FCC/USA
- Channel
- Frequency
- China
- Japan
- New Zealand
- Australia
- Europe
- Canada
- FCC/USA
- Channel
- Frequency
- 6: Bluetooth Specifications
- Description
- Feature
- 7: Antenna Connection Options
- Approved Region
- Vendor Part Number
- Vendor
- Lantronix Part Number
- Peak Gain Typical
- Antenna Type
- Peak Gain Typical
- Antenna Type
- 8: Electrical Characteristics
- Units
- Max xPico 250
- Max xPico 240
- Typical xPico 250
- TypicalxPico 240
- Soft AP
- Power Mgmt
- Parameter
- Units
- Max xPico 250
- Max xPico 240
- Typical xPico 250
- Typical xPico 240
- Soft AP
- Power Mgmt
- Parameter
- Units
- Peak Current Typical
- Average Current
- Soft AP/Wi-Fi Client
- Power Mgmt
- Parameter
- Unit
- Tolerance
- TYP.
- Rate
- Mode
- Unit
- Max
- TYP.
- Min.
- Rate
- Mode
- Unit
- Maximum
- Maximum RF Receive Level
- Unit
- Maximum
- Maximum RF Receive Level
- Unit
- Maximum
- Maximum RF Receive Level
- Unit
- Max
- Rate
- Mode
- Typical
- Receiver Characteristics
- Unit
- Maximum
- Minimum
- Description
- Parameter
- Unit
- Maximum
- Minimum
- Description
- Parameter
- Unit
- Maximum
- Minimum
- Description
- Parameter
- 9: Package Description and Mechanical Footprint
- Description
- Category
- 10: Product Information Label
- Example
- Description
- Field
- 11: Compliance
- Labeling of the End Product
- Federal Communication Commission Interference Statement (xPico 240/250)
- Industry Canada Statement (xPico 240/250):
- Radiation Exposure Statement:
- Déclaration d'exposition aux radiations:
- This device is intended only for OEM integrators under the following conditions: (For module device use)
- Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositive module)
- IMPORTANT NOTE:
- NOTE IMPORTANTE:
- Plaque signalétique du produit final
- Manual Information To the End User
- Manuel d'information à l'utilisateur final
- Caution :
- Avertissement:
- RoHS, REACH, and WEEE Compliance Statement
- 12: Ordering Information
- Description
- Part Number
- Description
- Part Number
- Description
- Part Number
xPico
®
200 Series Embedded Wi-Fi
®
Gateway Data Sheet 28
Table 5-3: 40 MHz Channels
Frequency Channel FCC/USA Canada Europe Australia New
Zealand
Japan China
5 GHz Band
5190 38 Yes Yes Yes Yes Yes Yes Yes
5230 46 Yes Yes Yes Yes Yes Yes Yes
5270 54 Yes Yes Yes Yes Yes Yes Yes
5310 62 Yes Yes Yes Yes Yes Yes Yes
5510 102 Yes Yes
Yes
Yes
Yes
Yes
-
5550 110 Yes Yes
Yes
Yes
Yes
Yes
-
5590 118 Yes Yes
Yes
-
Yes
Yes
-
5630 126 Yes Yes
Yes
-
Yes
Yes
-
5670 134 Yes Yes
Yes
-
Yes
Yes
-
5755 151 Yes Yes
-
Yes
Yes
-
Yes
5795 159 Yes Yes
-
Yes
Yes
-
Yes
Table 5-4: Preliminary 80 MHz Channels (xPico 270 only, Preliminary)
Frequency Channel FCC/USA Canada Europe Australia
New
Zealand
Japan China
5 GHz Band
5210 42 Yes Yes Yes Yes Yes Yes Yes
5290 58 Yes Yes Yes Yes Yes Yes Yes
5530 106 Yes Yes
Yes
Yes
Yes
Yes
-
5610 122 Yes Yes
Yes
-
Yes
Yes
-
5690 138 Yes Yes
Yes
-
Yes
Yes
-
5775 155 Yes Yes
-
Yes
Yes
-
Yes
Notes:
1. Frequencies from 5150 Mhz to 5250 Mhz for indoor use only.
2. The unit supports 20 MHz bandwidth channels for 2.4 Ghz channels.
3. The unit supports 20, 40 MHz bandwidth channels for 5 Ghz channels.
4. xPico 270 supports 80Mhz bandwidth channels for 5Ghz channels.
5. Country code modifications are not available to the end user.
6. If the unit is connected as a client to an external AP, the soft AP channel follows the external
AP. Otherwise, the Soft AP defaults to automatically choosing a channel based on RSSI and
channel usage. A unit that is not connected to an external AP may also be configured for a
specific channel.
7. In Soft AP mode, the product will not initiate any connection or active scan in 5G DFS bands
and will only follow external AP or master device to use a channel.