User's Manual

ManualsBrandslantronix ManualsElectronicsDRIG WIRELESS DEVICE SERVER

Table Of Contents

Figures
Tables
Using This Guide
- Purpose and Audience
- Summary of Chapters
- Additional Documentation
Introduction
- Product Description
- Industrial Automation Protocols
- Network Protocols (Serial Tunneling)
- XPress DR+ Application Examples
- Addresses and Port Numbers
- Configuration Methods
Installation and Hardware
- What's in the Box?
- Physically Connecting the XPress DR+
- XPress DR+ Front Panel
- Serial Interface
- Ethernet Interface
- Power Requirements
- Reset Switch
- LEDs
- Dimensions
- Wall Mount Bracket
- Product Information Label
XPress DR+W
- Application Examples
- Physically Connecting the XPress DR+W
- Front Panel Description
- LEDs
- Required Information for Initial Configuration
- Installing the XPress DR+W for Initial Configuration
- Server Configuration (Option 0)
- WLAN Configuration (Option 4)
- Next Steps
Using DeviceInstaller
- Installing DeviceInstaller
- Assigning an IP Address
- Accessing the XPress DR+ Using DeviceInstaller
- Viewing the Current Configuration
Configuration Using Web Manager
- Accessing XPress DR+ Using DeviceInstaller
- Network Configuration
- Server Configuration
- Host List Configuration
- Channel Configuration
- WLAN Configuration (XPress DR+W only)
- Applying Settings
- Applying Factory Defaults
Configuration Using Telnet or Serial Port (Setup Mode)
- Accessing Setup Mode
- Exiting Setup Mode
Setup Mode: Server Configuration
- Server Configuration (Option 0)
- DHCP Name
Setup Mode: Channel Configuration
- Channel 1 (Option 1) and Channel 2 (Option 2)
- Baudrate
- I/F (Interface) Mode
- Flow
- Port Number
- Connect Mode
- Send the Escape Sequence (+++) in Modem Mode
- Auto Increment Source Port
- Remote IP Address
- Remote Port
- DisConnMode
- Flush Mode (Buffer Flushing)
- Pack Control
- DisConnTime (Inactivity Timeout)
- Send Characters
- Telnet Terminal Type
- Channel (Port) Password
- WLAN Settings (XPress DR+W Only)
Setup Mode: Advanced Settings
- Expert Settings (Option 5)
- Security Settings (Option 6)
- Default Settings (Option 7)
Firmware Upgrades
- Obtaining Firmware
- Reloading Firmware
Monitor Mode
Troubleshooting and Technical Support
- Problems and Error Messages
- Technical Support
Technical Specifications
Lantronix Cables and Adapters
Alternative Methods of Assigning an IP Address
Binary to Hexadecimal Conversions
- Converting Binary to Hexadecimal
Compliance Information
- Declaration of Conformity
- XPress DR+W Regulatory Information
Warranty

Chapter 3: Installation and Hardware

XPress DR+ User Guide 21

Table 3-1. RJ45 Serial Connector Pinouts

Pin Direction Name Function

1 Output from DR+ RTS Ready To Send

2 Output from DR+ DTR Data Terminal Ready

3 Output from DR+ TXD Transmitted Data

4 Ground GND Signal Ground

5 Ground GND Signal Ground

6 Input to DR+ RXD Received Data

7 Input to DR+ DSR Data Carrier Detected

8 Input to DR+ CTS Clear To Send

Screw Terminal Serial Connectors

Table 3-2. Serial Screw Terminal Pinout for RS422 (4-Wire)

Pin Direction Name Function

1 Output TX+ Transmit Data +

2 Output TX- Transmit Data -

3 Ground GND Signal Ground

4 Input RX+ Received Data +

5 Input RX- Received Data -

Table 3-3. Serial Screw Terminal Pinout for RS485 (2-Wire)

Pin Direction Name Function

1 Bi-directional TX+/RX+ Transmit Data + and Received Data +

2 Bi-directional TX-/RX- Transmit Data – and Received Data -

3 Ground GND Signal Ground

4 Not Applicable Not Applicable Not Used

5 Not Applicable Not Applicable Not Used

Figure 3-4. Screw Terminal Ports

Figure 3-3. RJ45 Connector – Front View