VBD 1800 OWNER’S MANUAL Mobile Audio System • PLL Synthesizer Stereo Radio • Digital Compact Disc Player • Automatically Memory Storing • Turn Upside Down Detachable Panel • Preset Equalization
CONTENTS Installation .....................................................................................................3 DIN Front-Mount (Method A) ..................................................................................3 Installing the unit ...............................................................................................3 Removing the unit .............................................................................................4 DIN Rear-Mount (Method B) ....................
INSTALLATION Notes: DIN FRONT-MOUNT (Method A) • Choose the mounting location where the unit will not interfere with the normal driving function of the driver. Installing the unit 1 2 • Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. 182 53 3 • Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. (Fig. 1) 1.
INSTALLATION Removing the unit 1. 2. 3. 4. Factory-installed radio bracket Car radio mounting bracket Screw After aligning the car radio mounting bracket with the factory-installed radio bracket, tighten the screws (5 x 5mm) at 2 places on each side. 5. When fixed factory-installed radio bracket with the screws, use a standard-tipped screwdriver to pry the tabs of the car radio mounting bracket to make them fit into the holes in the factory-installed radio bracket. 6. Movable panel frame 1 2 3 1.
USING THE DETACHABLE FRONT PANEL 3. When the front panel is in State 3, press button, the front panel will slide down to State 2. Press button again, the panel will slide up. When the front panel is in State 2, slide the bottom button of the front panel leftward and pull it out from the panel bracket. And the panel bracket will slide up automatically. To Detach the Front Panel 1.
USING THE DETACHABLE FRONT PANEL 5. Do not expose the front panel to high temperatures or direct sunlight in anywhere. To Reinstall the Front Panel 1. When the panel bracket is in slide up position, insert left side of the front panel to its proper position and push right side into the panel bracket, a ‘click’ sound should be heard. 6. Keep away any volatile agents (e.g. benzene, thinner or insecticides) from touching the surface of the front panel. 7. Do not attempt to disassemble the front panel.
WIRING CONNECTION MAIN UNIT ANTENNA CONNECTOR (GREEN) IGNITION RED SWITCH (B+) MEMORY YELLOW BACK-UP BLACK GROUND (B–) CHOKE BOX SUBWOOFER CABLE (BROWN) Rch RED FRONT RCA CABLE Lch WHITE (GREY) POWER ANTENNA BLUE REAR RCA CABLE Rch RED Lch WHITE FRONT Lch SPEAKER REAR Lch SPEAKER WHITE GREY WHITE/BLACK GREY/BLACK GREEN VIOLET GREEN/BLACK VIOLET/BLACK 7 FRONT Rch SPEAKER REAR Rch SPEAKER
OPERATION 10 2 24 7 11 12 6 15 26 19 20 8 23 21 14 16 17 22 4 1 13 18 9 25 3 5 removable faceplate. GENERAL OPERATION • SOUND ADJUSTMENT Press SEL button (10) to select the desired adjustment mode. The adjustment mode will change in the following order: • ON/OFF Switch on the unit by pressing the lefttop inside button of the back of them front panel. And the front panel will turn upside down from State 1 to State 2 to State 3.
OPERATION • RESET RESET button (26) must be activated with either a ball point pen or thin metal object. RESET button (26) is to be activated for the following reasons: - Initial installation of the unit when all wiring is completed. - All the function buttons do not operate. - Error symbol on the display. • LOUDNESS Press BND/LOUD button (13) for several seconds to increase bass output and display will show “LOUD ON”. Press it again for several seconds to release this function.
OPERATION You can sometimes improve reception of distant stations by selecting mono operation. When there is a disc in, press button (7), the panel will slide down. Then press EJECT button (4) to stop CD playing and eject the disc from the disc slot (5). Press button (7) again to slide up the front panel. • SCAN Press SCAN button (25) to set function to scan mode, which scanning to higher frequency station with receivable signal and keep on each station for several seconds.
OPERATION • PREVIEW ALL TRACKS Press SCN button (20) to play first several seconds of each track on the current disc. Press again to stop intro and listen to track. • PLAY ALL TRACKS Press SHF button (22) to play all tracks on CD in random order. Press again to cancel the function. NOTE ON CD-R/CD-RW DISCS • On this unit, in addition to an audio CD, you can play your original CD-R or CD-RW that contain audio titles.
REMOTE CONTROL HANDSET 1 7 4 3 8 9 6 5 13 2 12 10 11 14 15 FUNCTION KEYS & CONTROL 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15.
SPECIFICATION GENERAL Power Supply Requirements Chassis Dimensions Tone Controls - Bass (at 100 Hz) - Treble (at 10 KHz) Maximum Output Power Current Drain : DC 12 Volts, Negative Ground : 178 (W) x 165 (D) x 50 (H) : : : : ± 10 dB ± 10 dB 4 x 60 Watts 15 Ampere (max.) CD PLAYER Signal to Noise Ratio Channel Separation Frequency Response : More than 55 dB : More than 50 dB : 20 Hz - 20 KHz RADIO FM 87.5 to 107.9 MHz 10.
TROUBLE SHOOTING Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer. Symptom No power. Disc cannot be loaded or ejected. Cause Solution The car ignition switch is not on. If the power supply is properly connected to the car accessory circuits, but the engine is not moving, switch the ignition key to “ACC”. The fuse is blown. Replace the fuse. Presence of CD disc inside the player.
www.lanzar.