USER’S MANUAL AMPLIFIERS: MAXP 1200 / 1055D / 1201D / 1601D / 2051D / 2055D / 2651D
TABLE OF CONTENTS Contents and introdction - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page J Amplifier featuer descriptions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - _.
AMPLIFIER FEATUER DESCRIPTIONS ~I055D/~IZOID/~160ID ~IZOO ~Z05ID/~Z65ID/~Z055D o ~, ~. I. Une Out RCA Jacks· The LINE OUT allows you to build multiple amplifier systems without having to use splitter cords to distribute the signal. Now it is simple a matter of bringing one set of RCAs into the first amplifier, then using the line out RCA jacks as the feed to the next amplifier. 5. Brigde Mode 6. Variable Bass Boost Control· 0 - + 10dB Always use high quality shielded RCA cables. 3.
MAXPI ZOO MONO BLOCK AMPLIFIER APPLICATIONS Basic application Interconnect cable checklist: - Connect the line inputs to a Radio/CD RCA outputs or line output of the full range primary amplifier with good quality RCA cables. A "Y" adapter may be needed as shown in the diagram. - Use at least 16 gauge speaker wiring.
~PI055D/~PI201D/~PI601D/~P2051D/~P2651D ~P2055D MONO BLOCK CLASS D AMPLIFIER APPLICATIONS Basic application Interconnect cable checklist: - Connect the line inputs to a Radio/CD RCA outputs or line output of the full range primary amplifier with good quality RCA cables. A "Y" ada per may be needed as shown in the diagram. - Use at least 16 gauge speaker wiring. These amplifiers have dual speaker terminals, simplifYing the hookup of multiple speakers _0 8UBWOOFER nl!RBJU1I1! .
SETTING UP SYSTEMS AFTER INSTALLATION FOR BEST PERFORMANCE General: At this point you are ready to get more specific on the settings for your amplifier. Subsonic: This setting acts as a low frequency cut off for your system bass reproduction. The point that you set it at cuts off any frequencies from reproduction beyond this point. The 12 o'clock position is a great starting point.
Lanzar MAX PRO SERIES AMPLIFIER FEATURES output Power Rating MAXPI200 MAXPIOSSD MAXPI20lD MAXPI60lD MAXP20SID MAXP205SD MAXP26SID 4Ohmload 2-Ohm load 450xl 900xl Ix250W lx500W Ix500W Ix 1OOOW Ix750W lx1500W lxl000W lx2000W lx625W lx1250W lx1250W lx2500W l-Ohm load O.S-Ohm load 1800xl NA lxl000W lx2000W lx2000W NA lx3000W NA lx4000W NA lx2500W lx5000W lx5000W NA YES >200 >95d8 <0.05% YES >300 >95dB <0.50% YES >300 >95dB <0.50% 0.2V-9V 0.04V- 18V 47k-Ohm YES >300 >95dB <0.50% 0.2V-9V 0.
TROUBLESHOOTING Before removing your amplifier, refer to the list below and follow the suggested procedures. Always test the speakers and their wires first. AMPLIFIER WILL NOT POWER UP. Check for good ground connection. Check that remote DC terminal has at least 13.Bv DC. Check that there is battery power on the +terminal. Check all fuses. Check that Protection lED is not lit. If it is lit shut off amplifier briefly and then repower it. HIGH HISS OR ENGINE NOISE (ALTERNATOR WHINE) IN SPEAKERS.
() ) *+* !!! " # $ %&'