4-Band Parametric Equalizer with Subwoofer Gain Control and Wireless BT Audio Connectivity
TABLE OF CONTENTS 1. FEATURES 3 2. PRECAUTIONS 3 Installation 3 3. CONTROLS 4 4. OPERATIONS 5 Setting system volume 5 Adjusting the controls 5 Setting the low-pass frequency 5 Connecting an MP3 player or video unit 6 Care and maintenance 6 5. INSTALLATION AND WIRING 7 What's in the Box 7 Before starting 7 Tools and additional components 8 Mounting Diagram 8 Wiring diagram 9 6.
FEATURES LANZAR HTG50EBTH is a 4-band stereo equalizer/crossover/Wireless BT specifically created for the mobile environment. The HTG50EBTH provides powerful features in a compact size: • Four equalization bands (150Hz, 400Hz, 2.5KHz, 15KHz), each frequency adjustable from -12 to +12dB. • Subwoofer output uses a built-in 12dB per octave electronic crossover fixed at 40Hz to 120Hz.
CONTROLS 4 www.Lanzar.
OPERATIONS Setting system volume 1. Turn the master volume and subwoofer level controls to their minimum settings. 2. Turn the source unit on and increase the volume until you hear distortion. 3. Reduce the volume to just below the distortion point (approximately 80% of full volume). This is the maximum usable musical signal for the source unit. Turning the volume beyond this point increases noise and distortion without increasing the musical signal.
Connecting an MP3 player or video unit 1. Plug the MP3 player or video unit into the auxiliary RCA input on the back of the HTG50EBTH unit. 2. Make sure the auxiliary button on the front of the unit is out, ready to receive input from the main RCA input (not the auxiliary RCA input). 3. Turn the HTG50EBTH master volume to a normal listening level. 4. Press the play button on the auxiliary source. 5. Push in the AUX button to change to the auxiliary source. 6.
INSTALL ATION AND WIRING Read these instructions and the following precautions carefully. What's in the Box: • 4-Band Parametric Equalizer Before Starting Mounting Precautions The HTG50EBTH can be mounted next to the source unit or under the dash using the mounting brackets. The front panel controls should be easily accessible from the driver's seat. In addition: • This unit requires additional mobile audio components for proper operation.
Tools and additional components You will need: • A Philips-head screwdriver when mounting the unit in the vehicle. • A small flat-head screwdriver to adjust the AUX gain controls if you connect an MP3 player or video source. • High-quality RCA input and output cables. Extra cable can cause signal loss and act as an antenna for noise. Use only high-quality RCA cables that are no longer than necessary to make a direct connection with the source unit and amplifiers. Mounting Diagram 8 www.Lanzar.
www.Lanzar.
Troubleshooting The unit does not work: No lights The power wires may not be connected. Check the power and ground wiring, then retest. Sound is Distorted • The source unit volume may be set too high. Reduce the source unit volume. • Equalizer gain controls are set too high. Turn the equalizer controls to the center position and listen for distortion again. If the problem still occurs, see your authorized LANZAR dealer. • Speakers may be damaged. Consult your authorized LANZAR dealer.
Specifications Features: • 4 Band Parametric Equalizer • Half Din Size • 9 Volt RMS Pre-Amp Output • Pre-amp Line Aux Inputs Via RCA Jacks • 3 Input Source Selectable • Input Gain Adjustments • Wireless BT Audio Connectivity • RCA AUX Input Jack • Source/Aux/ BT Input Selector • Rotary Fader • Output Volume Control • Sub Output Volume Control • Blue Light Illumination • Mounting Hardware Included • DC 12 Volt with Remote Trigger Wireless BT Streaming: • Built-in BT for Wireless Music Streaming • Simple & Ha
Questions? Issues? We are here to help! Phone: (1) 718-535-1800 Email: support@lanzar.