USER’S MANUAL AMPLIFIERS: RS: RS S: MAXP 2760/MAXP 2960/MAXP 4260
TABLE OF CONTENTS Contents and introdction - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 1 Amplifier featuer descriptions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - _. Page 2 MAXP2760/MAXP2960 channel amplifier applications- - - - - - - - - - - - - - - - - - - - - - - - - - - - - _.
AMPLIFIER FEATUER DESCRIPTIONS ~Z760fNU'XPZ960 Z CHANNELAMPUFIERS The X..oVER slide switch selects the intermal crossover functions: - The input signal is routed directiy to the UNE OUT RCA jacks. regardless of the X-OVER setting simplifying daisy chaining of amplifiers. • HP: Selects the built in HIGH PASS filter. variable from 40 Hz to 2KHz. • FlAT: Bypasses all crossovers for full frequency range operation. LP: Selects the built in LOW PASS filer. variable from 30 Hz to 150Hz.
MAXP2760/MAXP2960 2 CHANNEL AMPLIFIER APPLICATIONS FULL RANGE STEREO This ;s the most basic application for the MAX PRO Series 2 channel amplifiers. FUll. RANGE SPEAKERS Q 1. Interconnect cable checklist: Connect the UNE INPUTS to the Radio/CD with good quality RCA cables. 3. Crossover frequency control checklist: f~: 11'11 ;e: 4.Line level: Refer to the section "Setting up systems after installation for best performance- ~ r~ b£([J1flf1:Ecm[!D ilSl ' L""", L :6), foo/ S. Bass Remote: "C.
MAXP4260 4 CHANNEL AMPLIFIER APPLICATIONS 4 CHANNEL FULL RANGE SYSTEM Here we show how to use the 4 channel amplifiers as straightforward discrete 4 channel full range units. ~ Interconnect c.ble checldlst: - Connect the four inputs of the amplifier to a Radio/CD with quality RCA cables, SWItch .enlng checklist: -ljZCH X'()VER: FULL -3/4CH X'()VER: FULL Crossover frequency control checklist: Channel. I/Z: Channel.
MAXP4260 4 CHANNEL AMPLIFIER APPLICATIONS 2 way active, or b .... mpllfted system with mono bass Level control checklist: This application shows how easily a 2 way active system can be implemented using a MAX PRO series 4 channel amplifier. Channels I and 2 will be used for highs, and channels 3 and 4 for mono bass. Refer to the section "setting up systems after in stall ation for best performance" ·2 ohm per channel in stero mode Interconnect cable checklist: ·4 ohm mono bridged.
MAXP42604 CHANNEL AMPLIFIER APPLICATIONS Front/ear high pass, using a Z channel amplifier for mono sub bass The combination of a 2 and a 4 channel amplifier, utilizing their built in crossovers. makes it a snap to put together a full system with front and rear highs. with mono sub bass. Interconnect cable checklist: - Using good quality RCA cables. feed the front and rear outputs of a head unit to the inputs of the 4 channel amplifier as shown.
SETTING UP SYSTEMS AFTER INSTALLATION FOR BEST PERFORMANCE General: At this point you are ready to get more specific on the settings for your amplifier. HIgh Pass: -When in Hi Pass operation, this setting acts as a low frequency cut off for your system reproduction. The point that you set it at cuts off any frequencies from reproduction beyond this point. The 12 o'clock position is a great starting point. EXAMPLE: If you adjust the High Pass to 100Hz.
Lanzar MAX PRO SERIES AMPLIFIER FEATURES MODEL MAXP2760 MAXP2960 MAXP4260 Out Power Rating RMSat40hms MAX at 4 Ohms MAX at 4 Ohms Bridced RMSat 2 Ohms 500Wx2 1000Wx2 1200Wxl BOOWx2 750Wx2 1500Wx2 3000Wxl 1200Wx2 250Wx4 500Wx4 1000Wx2 400Wx4 Yes 10Hz-40KHz >200 > 95dB <0.05% >70dB 0.2V-6.0V 20kQ Power/Protect Yes Yes Yes Yes 10Hz-40KHz >200 > 95dB <0.05% >70dB 0.2V-6.0V 20kQ Power/Protect Yes Yes 10Hz-40KHz >200 > 95dB <0.05% >70dB 0.2V-6.
TROUBLESHOOTING Before removing your amplifier, refer to the list below and follow the suggested procedures. Always test the speakers and their wires first. AMPLIFIER WILL NOT POWER UP. Check for good ground connection. Check that remote DC terminal has at least 13.8v DC. Check that there is battery power on the +terminal. Check all fuses. Check that Protection LED is not lit If it is lit. shut off amplifier briefly and then repower it. HIGH HISS OR ENGINE NOISE (ALTERNATOR WHINEI IN SPEAKERS.
() ) *+* !!! " # $ %&'
