5 Band Parametric Equalizer with Voltage Meter, Subwoofer Gain Control and Bass Driver
TABLE OF CONTENTS 1. FEATURES 3 2. PRECAUTIONS 4 Installation 4 3. CONTROLS 5 4. OPERATIONS 6 Setting system volume 6 Adjusting the controls 6 Setting the low-pass frequency 6 Connecting an MP3 player or video unit 7 Care and maintenance 7 5. INSTALLATION AND WIRING 7 What's in the Box 7 Before starting 8 Tools and additional components 9 Mounting Diagram 9 Wiring diagram 6.
FEATURES LANZAR VIBE530P is a 5-band stereo equalizer / crossover specifically created for the mobile environment.
PRECAUTIONS • Do not operate this product in ways other than those described in this manual. • Do not disassemble or modify this unit. • Do not pour liquid or poke foreign objects into the unit. Water and humidity may damage internal circuitry. • If the unit becomes wet, turn off all power and ask your authorized LANZAR dealer to clean or service the unit. Failure to observe these precautions may damage your ear, the monitor, or the video source, and may void the warranty.
CONTROLS Voltage Level Indicator Equalizer gain controls Master volume Subwoofer volume Fader control: Use to balance sound between front and rear speakers AUX(auxiliary)switch: Press to select auxiliary or main inputs - Front panel controls - - Rear panel connections Aux gain control: Gain adjustment for left and Para- Bass Controls: These 2 knobs control the right auxiliary input Para-Bass functions of the VIBE530P.
OPERATIONS Setting system volume 1. Turn the master volume and subwoofer level controls to their minimum settings. 2. Turn the source unit on and increase the volume until you hear distortion. 3. Reduce the volume to just below the distortion point (approximately 80% of full volume). This is the maximum usable musical signal for the source unit. Turning the volume beyond this point increases noise and distortion without increasing the musical signal.
Connecting an MP3 player or video unit 1. Plug the MP3 player or video unit into the auxiliary RCA input on the back of the VIBE530P unit. 2. Make sure the auxiliary button on the front of the unit is out, ready to receive input from the main RCA input (not the auxiliary RCA input). 3. Turn the VIBE530P master volume to a normal listening level. 4. Press the play button on the auxiliary source. 5. Push in the AUX button to change to the auxiliary source. 6.
Before Starting Mounting Precautions The VIBE530P can be mounted next to the source unit or under the dash using the mounting brackets. The front panel controls should be easily accessible from the driver's seat. In addition: • This unit requires additional mobile audio components for proper operation. • Always use great care when attaching anything to a vehicle! Check clearances in front of, behind, and on both sides of the planned installation before drilling any holes or installing any screws.
Tools and additional components You will need: • A Philips-head screwdriver when mounting the unit in the vehicle. • A small flat-head screwdriver to adjust the AUX gain controls if you connect an MP3 player or video source. • High-quality RCA input and output cables. Extra cable can cause signal loss and act as an antenna for noise. Use only high-quality RCA cables that are no longer than necessary to make a direct connection with the source unit and amplifiers. Mounting Diagram www.Lanzar.
Wiring Diagram 10 www.Lanzar.
Wiring Diagram www.Lanzar.
Troubleshooting The unit does not work: No lights The power wires may not be connected. Check the power and ground wiring, then retest. Sound is Distorted • The source unit volume may be set too high. Reduce the source unit volume. • Equalizer gain controls are set too high. Turn the equalizer controls to the center position and listen for distortion again. If the problem still occurs, see your authorized LANZAR dealer. • Speakers may be damaged. Consult your authorized LANZAR dealer.
Specifications Features: • 5 Band Parametric Equalizer • Half Din Size • 9 Volt RMS Pre-Amp Output • Pre-amp Line Aux Inputs Via RCA Jacks • 3 Input Sources Selectable • Input Gain Adjustments • RCA AUX Input Jack • Source/Aux Input Selector • Rotary Fader • Output Volume Control • Sub Output Volume Control • Sub Effect (Sweep, Wide) Control • Sub Effect Volume Control • Blue Light Illumination • Mounting Hardware Included • DC 12 Volt with Remote trigger • RCA Auxiliary Input (Rear) inputs for MP3, DVD, or Ph
Questions? Issues? We are here to help! Phone: (1) 718-535-1800 Email: support@lanzar.
