Data Sheet

ManualsBrandsLAPP ManualsBus CablesBus cable UNITRONIC® BUS 1 x 2 x 0.32 mm² V

U.I. Lapp

GmbH

DATA SHEET

UNITRONIC BUS PB FD P 1 x 2 x 0,64

DB2170222

valid from: 28.10.2011

Originator: RAWE/PDC

approved: HAPF/PDC

Document: DB2170222 page 1 of 2

PD 0019/2.2_11.10DE

Application

Highly flexible data cable for the SIEMENS field-net SINEC L2 DP (acc. to DIN 19245, part 3 and EN 50 170) for fieldbus

system FIP (Factory Instrumentation Protocol) as well as for high performance data networks with 150 Ω nominal

impedance. The cable is designed for the system-defined transmission rates of 1.5 MBit/s, 2.5 MBit/s and 12 MBit/s, the

transmission characteristics are conform to the system and guarantee a high operating security during the data

transmission. The used materials are halogen free.

The cable is intended for high flexible application in power chains, on permanently moving machines and linear robots. Due

to its double screening it is suitable for installation in electromagnetically demanding areas. The PUR-sheath is very resistant

against mineral oils and abrasion.

Design

Conductor bare copper, nom. 0.25 mm

(24 AWG)

Insulation

Skin-Foam-Skin PE, core ∅ nom. 2.55 mm

Core identification code cores red and green

Stranding 2 cores together with 2 fillers

Wrapping 1 layer non woven tape

Screening plastic-laminated aluminium foil, side with metal outwards, braid of tinned

copper wires, coverage nom. 85%

Outer sheath PU flame retardant and halogen free, violet similar to RAL 4001,

wall thickness nom. 1.0 mm, outer diameter: max. 8.0 mm

Electrical properties at 20° C

Resistance (loop) max. 145 Ω/km

Insulation resistance min. 5 GΩxkm

Mutual capacitance A/A: ca. 32 nF/km

A/S: ca. 49 nF/km

(at 800 Hz)

Inductance 800 Hz: ca. 0.82 mH/km

Characteristic impedance 9,6 kHz: 270 Ω ± 27

38,4 kHz: 185 Ω ± 18

3 bis 20 Mhz: 150 Ω ± 15

Line attenuation 9,6 kHz: max. 0.3 dB/100 m

38,4 kHz: max. 0.4 dB/100 m

4 MHz: max. 2.5 dB/100 m

16 MHz: max. 4.9 dB/100 m

Velocity of propagation nom. 0,81c

Transfer impedance up to 20 MHz max. 10 mΩ/m

Operating peak voltage 220 V (not for power purposes)

Test voltage U

eff.

core/core und

core/screen

1500 V

Summary of content (2 pages)

PAGE 1
U.I. Lapp GmbH DATA SHEET UNITRONIC BUS PB FD P 1 x 2 x 0,64 DB2170222 valid from: 28.10.2011 Application Highly flexible data cable for the SIEMENS field-net SINEC L2 DP (acc. to DIN 19245, part 3 and EN 50 170) for fieldbus system FIP (Factory Instrumentation Protocol) as well as for high performance data networks with 150 Ω nominal impedance. The cable is designed for the system-defined transmission rates of 1.5 MBit/s, 2.
PAGE 2
U.I. Lapp GmbH DATA SHEET UNITRONIC BUS PB FD P 1 x 2 x 0,64 DB2170222 valid from: 28.10.2011 Mechanical and thermal properties Minimum bending radius 65 mm Permissible temperature range moved: -30˚ C up to +70˚ C Flame propagation flame retardant acc. to IEC 60332-1-2 Halogen free acc. to VDE 0472-815 general requirements Dangerous and forbidden substances acc. to RoHS directive (2002/95/EG) are not allowed to the manufacturing. Originator: RAWE/PDC approved: HAPF/PDC All rights reserved acc.