Datasheet

ManualsBrandsLapp ManualsCable & WireStranded Wire PVC 10mm² Bare Copper Green / Yellow H07V-K 50m

U.I. Lapp

GmbH

DATA SHEET

H07V-K

DB8120001EN

valid from: 11

Sept. 2014

Originator: T. Merker / PCM

approved: HAPF / PDC

Document: DB8120001EN

page 1 of 1

PD 0019/2.2_11.10EN

APPLICATION (HD 516)

H07V-K belongs to Europe’s harmonized, normative cable types and is designed according to the CENELEC harmonized third-party stand-

ard EN 50525-2-31 – formerly: Meanwhile withdrawn harmonization document HD 21.3. H07V-K is a classic, single-layer insulated, single-

core, low-voltage hook-up wire, and that for stationary/ static and protected installation inside of devices/ appliances/ machines/ con-

trol cabinets (panels)/ cable ducting systems/ closed conduits for laying on or underneath plaster as well as in similar, closed systems

which cannot be opened if energized, since H07V-K doesn’t dispose of error correction/ protection for lack of an outer sheath (jacket),

but only of basic protection according to revised IEC 60364-4-41/ HD 60364-4-41. Beyond, H07V-K is suitable for the use in or on lighting

installation or control units/ switchgear in conjunction with voltages up to 1000 V AC or 750 V DC to-ground, according to HD 516. Un-

protected laying on or under plaster as well as wiring through unclosed or opening cable trunking systems is only permitted as part of

security irrelevant signal and control circuits with special extra-low voltage under 25 V AC to-ground or under 60 V DC to-ground. In wet or

damp rooms and locations, unprotected operation is completely forbidden. Under individual part numbers, different core insulation col-

ours are offered for diverse application types. Flat cardboard boxes containing 100-metre coils are applied as standard package type.

ETIM 5.0 Class-ID: EC000993

ETIM 5.0 Class-Description: Single core cable

DESIGN (EN 50525-2-31)

Conductor Copper, bare, fine-wired/ finely stranded/ conductor class 5 according to IEC 60228

Nominal conductor cross sections 1.5 mm² to and including 6 mm²

Core insulation PVC compound type TI 1 according to EN 50363-3

Core insulation colours Diverse single colours

Diverse double colours, with lengthways stripes

THIRD-PARTY CABLE TYPE CERTIFICATION (EN 50525-2-31)

◄VDE► H07V-K

Exceptions without cable type certification:

 Transparent core insulations

 Single-coloured, yellow core insulations

 Single-coloured, green core insulations

 Double-coloured core insulations, except for green-yellow and yellow-green

ELECTRICAL PROPERTIES AT +20 °C

IEC rated voltage U

/U 450/750 V AC = 675/1125 V DC

Conductor resistance IEC 60228, conductor class 5

Test voltage 2500 V AC

Compliance with the low-voltage EC directive 2006/95/EC

MECHANICAL, THERMAL AND CHEMICAL PROPERTIES

Minimum bending radius (HD 516) Intended use: 4 x Outer diameter

Cautious bending: 2 x Outer diameter

Conductor temperature Stationary/ static operation (without vibration): -40 °C to +80 °C

Moved operation (not normatively intended): +5 °C to +70 °C

Laying/ handling: Min. +5 °C

Short-circuit and ground leakage: Max. +160 °C

Ambient temperature at storage: Max. +40 °C

Flame retardant IEC 60332-1-2

RoHS Chemical compliance with the EU RoHS II directive 2011/65/EU about the Restriction of

(the use of certain) Hazardous Substances