Installation & Assembly

INSTALLATION AND SAFETY INSTRUCTIONS
FOR
YOUR
SAFETY
WARNING:
BE SURE THE ELECTRICITY TO THE WIRES
YOU ARE WORKING ON IS SHUT OFF; EITHER THE
FUSE IS REMOVED OR THE CIRCUIT
BREAKER
IS
SHUT
OFF.
GENERAL
You don't need special tools to install this fixture. Be sure
to follow the steps in the order given. Under no
circumstances should a fixture be hung on house electrical
wires, nor should a swag type fixture be installed on a
ceiling, which contains a radiant type heating system
.
Read
instructions carefully. If you are
unclear
as
to
how
to
proceed,
consult
a
qualified
electrician.
NOTE:
Proper wiring is essential
for the safe operation of this fixture.
FIXTURE ASSEMBLY
Carefully
removed
the
fixture
from
the
carton
and
check
that all
parts
are
included
as
shown
in
figure.
Be
careful
not
to
misplace
any
of
the
screws
or
parts,
which
are
needed
to
install this
fixture.
STEP
1:
Choose
the
suitable
number
of
stems
and
install
the
stem
(G,H,I)
into
the
coupling
(J),
then
thread
the
s
t
e
m
G
,
H
,
1
o
n
t
o
t
h
e
c
o
u
p
l
i
n
g
(
F
)
.
INSTALLATION
IMPORTANT:
Do not attach fixture directly to outlet box.
STEP
1: Thread the mounting screws (A) into the match
holes in the mounting bar (B).
STEP 2:
Secure mounting bar (B) to the outlet box with
outlet
box screws C .
GROUNDING INSTRUCTIONS
STEP 1:
Insert the green grounding screw into the hole with two
raised dimples on the mounting bar. Wrap the
ground wire from the fixture (if supplied) around
the green grounding screw, then connect it to
ground wire from the outlet box (if not fixed on the
outlet box) using a wire connector (not supplied). If
ground wire from the fixture is not supplied, wrap
the ground wire (if not fixed on the outlet box) from
the outlet box around the green grounding screw and
lighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
STEP 2:
Take note of the color of the wire(s) on your fixture.
Identify which group your fixture wire(s) falls into and
connect the wires according to the directions below:
'NOTE: When parallel wire (SPT-1 & SPT-2) 1s used, the
tracer wire is square shaped or ridged and the less tracer wire is
round in shape or smooth (seen best when viewed
from wire end.)
STEP 3: Take your fixture wire(s) from group A and place
evenly against the black wire from the outlet box. Do
NOT twist wires together before using wire connectors.
STEP 4:
Fit a wire connector over the wires and screw the
connector clockwise until you feel firmness.
STEP
5:
Try
gently
to
pull
the
connector
off
the
wires.
If you
can
pull the connector off, carefully re-do steps 3 and 4, as
above, and check again for a firm connection.
STEP 6:
Connect the fixture wire from group B to the white wire
from the outlet box in the same manner. Make sure no bare wires
can be seen outside wire connectors.
outlet box, Raise the canopy (D) allowing for th
e
mounting
screws
(A) to protrude through the holes on
canopy (D),
and
secure with the ball nuts (E)
To clean, wipe fixture with a soft cloth. Clean glass with a mild
soap Do not use abrasive materials such as scouring or
powders, steel wool or abrasive paper.

-c



 
-G


i



STEP 2: Place the glass (L) over the socket (K) and secure with
the retaining ring (M).
STEP 3: Install lamp. (Please do not exceed the maximum
capacity recommended on the socket.)
CLEANING
GROUP A: Connect to black
House Wire
GROUP B: Connect to white
House Wire
BLACK WHITE
*PARALLEL WIRE (round &
smooth)
*PARALLEL WIRE (square &
ridged)
WHITE OR GREY WITH
TRACER
WHITE OR GREY WITHOUT
TRACER
BROWN, GOLD OR BLACK
WITHOUT TRACER
BROWN, GOLD OR BLACK
WITH TRACER
FINAL ASSEMBLY
STEP 1: After wires are connected, tuck them
carefully inside