Installation & Assembly
ASSEMBLING & INSTALLATION INSTRUCTIONS
The drawing shown may not exactly match the product enclosed. However, the installation
instructions do apply to this product.
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
A
TTENTION! COUPER LE COURANT AU FUSIBLE OU UN DISJONCTEUR.
ASSEMBLING THE FIXTURE (Fig.2)
1. Return the arms to suitable position, see figure.2
2. Attach the column (J) onto the top coupling of the lamp body (K), by turning it clockwise
until tight.
3. Attach the pipe screw(N) into the bottom coupling of the lamp body(K), lock it securely
with
the hex nut. Attach the cover(O) to the bottom pipe screw of the lamp body, lock it
securely with the fixture loop
(P).
4. Slide the cover(M) onto the lamp holder, slide the candle sleeve(L) over the lamp holder.
5. Install the light bulbs(Not included) in accordance with the fixture specifications. NOTE:
DO NOT EXCEED THE SPECIFIED WATTAGE!
HANGING THE FIXTURE (Fig.1)
1.
Shut off the power at the circuit breaker and remove old fixture from ceiling, including
the old single bar. Shut off the power at the circuit breaker and remove old fixture from
ceiling, including the old single bar
.
2.
Carefully unpack new fixture and lay all the parts on a clea
r surface.
3.
T
hread nipple (C) into loop (F) until snug.
4.
Thread other end of nipple (C) with loop attached into single bar (D) until snug.
5.
Place lock washer (B) over end of nipple protruding through single bar and thread he
x
nut (A) onto nipple until tight.
6.
Take this single bar assembly and mount to ceiling junction box with junction bo
x
screws (E).
Tighten screws securely with screwdriver.
7.
Using proper chain pliers to open one end link of the chain provided and connect to the
fixture loop. Close the link.
8.
By measuring, determine correct number of links needed for proper hanging height.
Using proper chain pliers disconnect and discard remaining chain.
9.
Lace the fixture wires through the chain.
10.
Slip loop collar (H) over the chain, then do the same with
the canopy (G).
11.
Open the other end link of the chain and hang the fixture on the loop at the ceiling
.
Close the link.
12. Feed the fixture wires through the loop (F) and nipple (C) and pull until taut.
CONNECTING THE WIRES (Fig.3)
1. Take the black wire from the ceiling junction box and the smooth wire leg from t
he
fix
ture and twist bare ends together. Twist wire connector onto end of wire until snug
.
2.
Repeat same process with white junction box wire and ribbed wire leg of fixture
wire.
NOTE:
Twist wires together in the same direction you twist the wire connector ont
o
wires.
3.
If your junction box has a grounding wire (green or bare copper), attach this wire
and
the
bare copper wire from the fixture together as step 1.If junction box has no ground
wire, attach the bare copper fixture wire to the green ground screw on the crossbar
.
4.
Tuck these wire connections neatly into the ceiling outlet box and then raise the
canopy (G) all the way to the ceiling. Raise the loop (H) and thread onto ceiling loop
protruding through canopy.
Your installation is now complete. Return power to the junction box and test
the fixture.
J
K
L
M
N
O
P
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black(Hot)
FIXTURE
WIRES
White or
Ribbed
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
White
(Neutral)
HOUSE
WIRES
Green or Bare
Copper(Ground)
FIG.3
FIG.1FIG.2