Specification Sheet

Page: 2
Larson Electronics LLC www.LarsonElectronics.com
9419 E US HWY 175, Kemp, TX 75143 Phone: [phone] Fax: [phone] Email: [e-mail]
Buy American Compliant
The LEDP1X10WRE-RND-C Round Colored LED Light Fixture is ideal for a wide variety of uses including equipment, vehicle, military,
law enforcement and industrial manufacturing applications. This ultra compact LED light produces an 860 lumen output with low
voltage and amp draw, 50,000 hour service life, multiple color choices, and 12 to 32 volt compatibility providing operators with a
versatile and powerful LED lighting solution.
The LEDP1X10WRE-RND-C round colored LED light emitter from Larson Electronics produces 860 lumen of bright light while drawing less than
1 amp from a 12 volt electrical system. A single CREE XLamp MC-E® 10 watt LED producing 860 lumen is combined with high output reflector to
produce a narrow 10 degree spread spot beam approximately 650’ long. We also offer a floodlight versions with a 60 degree beam spread to
provide more light over a larger area nearer the fixture, making flood versions ideal for use as work lights. Combined with the colored diffuser,
this light offers red, amber, or blue light output color in addition to the stock white light. This particular unit is ultra compact at only 3.7 inches in
diameter by 4.5 inches tall, by 3.8 inches deep, which makes it ideal for applications where electrical power and mounting space is at a
premium.
Click Photo to Enlarge Click Photo to Enlarge Click Photo to Enlarge
The LEDP WRE series LED lights are waterproof to 3 meters, sealed against intrusion by dust and dirt and very ruggedly constructed to
withstand the most demanding environments, conditions and applications. An integral Pulse Width Modulation controller, small profile, low power
requirements, high durability and versatile mounting makes these LED lights ideal for a wide array of applications including but not limited to:
military, industrial manufacturing, machine visioning, security and law enforcement, boating, off-roading and commercial structure illumination.
Heat Management: Heat is the single largest factor in premature LED failure and color shifting. These LED units contain advanced drivers which
use pulse width modulation to control heat buildup rather than simple voltage regulators which are typically harsh on sensitive electronics and
can contribute to early LED failure. These units automatically sense the temperature of each LED and adjust the energy frequency or “duty cycle”
accordingly to maintain heat levels within acceptable ranges. This system in essence flashes current at an extremely fast on and off rate to each
LED based upon the LED’s core temperature. This flash rate is too fast to detect with the human eye, but provides precise control of the current
flowing to each LED and thus the heat it generates. This allows the LEDs to be driven at up to 100% capacity without overheating or visible loss
of light output. The LEDs are always driven at the same voltage but the duty cycle, however, is changed to alter how long the LEDs are actually
on or off. The end result is more light with less heat and longer LED life with an average 70% lumen maintenance after 50,000 hours.
PWM Control: The pulse width modulation drivers in this unit also provide secondary benefits through the ability to tap into a provided input wire
with an external pulse generator and adjust the duty cycle of the current being applied to the LEDs. Thus you can connect an external dimmer,
switch or pulse control and adjust the perceived output of the light, effectively causing the light to flash, dim or brighten to the desired levels.
Additionally, this method of controlling light output results in a corresponding drop in amperage draw, so if the duty cycle is cut back to 50% there
will be a matching 50% reduction in amperage draw. These units are also able to monitor and adjust input current to maintain the correct LED
voltage levels regardless of input levels across a specific range. These LEDP WRE series LED lights can operate on current ranging from 12 to
32VDC without any modifications necessary as a result. This ability to sense and adjust input current also provides protection against voltage
spikes and drops that can occur in vehicle electrical systems which would otherwise result in burning up or premature LED failure without it.