BRISA Retractable Screen Door Single Door Installation Instructions CALL US FIRST Do not return to the store. For assistance with your installation, or for additional product information, contact our Customer Care Team at 888-483-3768 or visit www.LARSONdoors.com. 2333 Eastbrook Drive, Brookings, SD 57006 888-483-3768 www.larsondoors.
A fresh approach to fresh air Thank you for purchasing a Brisa Retractable Screen Door from LARSON®. Make sure the retractable screen door you purchased is the correct size to fit your door. This retractable screen door fits a single inswing or single outswing door. PARTS CONTACT US FIRST Do not return to the store. For assistance with your installation, or for additional product information, contact our Customer Care Team at www.LARSONdoors.com.
Product terminology Use the following illustration and terminology to become familiar with your Brisa Retractable Screen Door parts and location. This will be helpful for following installation instructions.
Identify your sill and door type Before you begin installing your new retractable screen door, it is important to identify your sill and door type. If you have a short sill or an outswing door, you may need to make some modifications before proceeding to the installation steps. SILL TYPE DOOR TYPE Right/Left Inswing Screen assembly will mount on outside of the home. Additional steps required Flush Sill Sill is flush with the exterior trim. Long/Extended Sill Sill extends past the exterior trim.
Assembly process These instructions outline the step-by-step process to install a retractable screen door. Before starting, review all instructions and become familiar with the parts included. MEASURE YOUR DOOR TRIM OPENING This screen door is designed to fit door trim openings between 32" and 36" without modifications. If your door trim opening measures less than 32" wide, the top and bottom tracks will require cutting. Go to page 9 to complete this modification first.
Slide sill plate assembly onto bottom track. Sill Plate Assembly Bottom Track Do not deploy screen until it is assembled to doorway. Insert the flat ends of the top and bottom tracks into the decorative housing. STEP 2 INSERT SCREEN Place screen assembly onto door sill and lift into place. Flush and short sill – Assembly rests in a position where top of track is flush with bottom edge of sill. Long sill – Assembly rests in a position on top of sill.
Extend housings to the left and right evenly until the flanges are snug to the door trim/jamb. STEP 3 SECURE SCREEN Insert a housing screw into the predrilled screw hole at the top of screen housing flange to hold frame in place. Do not tighten completely. Interior View Center sill plate assembly on the door sill. Slide sill plate assembly extenders to each side to fill gaps. Drive sill screws 4" from either end and 4" to the left and right of center.
Insert housing screws into all remaining pre-drilled holes on each vertical housing flange (2 total per side). Tighten all screws. Pull the slider bar closed to verify the latch and latch hook align properly. Latch hook can be adjusted up or down to make the latching lock move secure. Latch hook can be adjusted as needed with a hand screwdriver. TIP: Latch hook can be oriented either hook up or down to connect with latch.
Product modification Minor modifications may be necessary to tailor the retractable screen to your application. Door trim openings that measure less than 32” will require track cutting to fit the door width. Outswing door installations require a change to the handle/lock assembly to move the lock mechanism to the inside of the home. NARROW DOOR TRACK MODIFICATION Measure your door trim opening and follow the example below to make your modifications.
Frequently Asked Questions Is maintenance required on my Brisa Retractable Screen Door? Dirt and debris should be vacuumed out of the tracks periodically. Do not use oily lubricants (like WD40) on the track as these tend to attract dirt, which can hinder the operation. If needed, occasional use of a silicone-based lubricant is acceptable.
Preguntas frecuentes ¿Requiere mantenimiento mi puerta corrediza con malla Brisa? La suciedad y los desechos se deben aspirar para retirarlos de los rieles periódicamente. No utilice lubricantes a base de aceite (como WD40) en el riel ya que estos tienden a atraer la suciedad, lo cual puede obstaculizar el funcionamiento. Si es necesario, el uso ocasional de un lubricante a base de silicona es aceptable.
Puertaque queabre abrehacia haciaafuera afuera– –modificación modificacióndel delproducto producto Puerta Hay dos escenarios individuales que requerirán modificaciones antes comenzar con Hay dos escenarios individuales que requerirán modificaciones antes dede comenzar con loslos pasos de instalación. Las aberturas de borde de lade puerta que midan menos de 68" un corte de pasos de instalación. Las aberturas de borde la puerta que midan menos derequerirán 32" requerirán rieles adecuarse al ancho de puerta.
Inserte los tornillos del montante en los demás orificios de cada brida del montante vertical (2 por lado en total). Ajuste todos los tornillos. Insérez les housing vis de boîtier d’encastrement dans tous les trous prépercés restants dans chaque barre verticale du cadre (2 de chaque côté). Serrez les vis. Verifique que el pestillo y el gancho del pestillo estén alineados correctamente. El gancho del pestillo se puede ajustar con un destornillador de mano, si es necesario.
7 Extienda los montantes en forma pareja a la izquierda y a la derecha hasta que se ajusten en el borde interno de la puerta. Étirez la moustiquaire de façon égale vers la gauche et la droite jusqu’à ce qu’elle se soit bien ajustée au cadre intérieur de la porte. PASO 3 ASEGURE LA MALLA Inserte un tornillo de montante en el orificio perforado previamente en la parte superior de la brida del montante de la malla para que el cuadro quede firme en el lugar. No ajuste los tornillos completamente.
Montaje de umbral Seuil de porte en métal Deslice el montaje de umbral sobre el riel inferior Sill Plate Assembly Slide sill plate assembly onto bottom track. Riel inferior Rail du bas Bottom Track Glissez le seuil de porte en métal sur le rail du bas Inserte los extremos planos de los rieles superior e inferior en el montante decorativo. Insérez les extrémités plates des rails du bas et du haut dans le cadre décoratif. Do not deploy screen until it is assembled to doorway.
5 Proceso de montaje Estas instrucciones describen paso por paso el proceso para instalar una puerta de malla retráctil. Proceso de montaje Antes comenzar, vuelva a leer todas instrucciones familiarícese conpuerta las mismas. Estasde instrucciones describen paso porlas paso el proceso ypara instalar una de malla retráctil. Antes de comenzar, vuelva a leer todas las instrucciones y familiarícese con las mismas.
Identifique su umbral y tipo de puerta Antes de comenzar a instalar la nueva puerta de malla retráctil, es importante que identifique el tipo de solera y de puerta. Si tiene una solera corta o una puerta que abre hacia afuera, es posible que deba hacer algunas modificaciones antes de continuar con la instalación.
Terminología producto Terminologíadel del producto Utilice la siguiente ilustraciónyy terminología terminología para familiarizarse con las y ubicación de Utilice la siguiente ilustración para familiarizarse conpiezas las piezas y la Puerta con malla Brisa. Esto le servirá las instrucciones delas instalación. ubicación decorrediza la Puerta corrediza con malla Brisa.
Una propuesta innovadora para tomar aire fresco Gracias por comprar una puerta de malla retráctil Brisa de LARSON®. Asegúrese de que la puerta de malla retráctil que compró sea del tamaño adecuado para su puerta. Esta puerta de malla retráctil se adapta a puertas simples que abren hacia adentro o hacia afuera. Une nouvelle façon de sentir l’air frais Merci d’avoir fait l’acquisition d’une porte-moustiquaire rétractable Brisa de ODL.
BRISA Retractable Screen Door Instrucciones para la instalación de la puerta simple Instructions d’installation pour une porte simple PRIMERO LLÁMENOS No devuelva el producto a la tienda. Si necesita ayuda con la instalación de su malla retráctil o si desea información adicional sobre el producto, llame a nuestro departamento de atención o visite nuestro sitio en Internet en www.LARSONdoors.com. APPELEZ-NOUS D’ABORD Ne retournez pas en magasin.