BRISA Retractable Screen Door Double Door Installation Instructions CALL US FIRST Do not return to the store. For assistance with your installation, or for additional product information, contact our Customer Care Team at 888-483-3768 or visit www.LARSONdoors.com. 2333 Eastbrook Drive, Brookings, SD 57006 888-483-3768 www.larsondoors.
A fresh approach to fresh air Thank you for purchasing a Brisa Retractable Screen Door from LARSON®. Make sure the retractable screen door you purchased is the correct size to fit your door. This retractable screen door fits a double inswing or double outswing door. CONTACT US FIRST Do not return to the store. For assistance with your installation, or for additional product information, contact our Customer Care Team at www.LARSONdoors.com.
Product terminology Use the following illustration and terminology to become familiar with your Brisa Retractable Screen Door parts and location. This will be helpful for following installation instructions.
Identify your sill and door type Before you begin installing your new retractable screen door, it is important to identify your sill and door type. If you have a short sill you may need to make some modifications before proceeding to the installation steps. SILL TYPE DOOR TYPE Double Inswing Screen assembly will mount on outside of the home. Flush Sill Sill is flush with the exterior trim. Long/Extended Sill Sill extends past the exterior trim.
Assembly process These instructions outline the step-by-step process to install a retractable screen door. Before starting, review all instructions and become familiar with the parts included. It may be helpful to have a second person assist you during the installation. MEASURE YOUR DOOR TRIM OPENING This screen door is designed to fit door trim openings between 68" and 72" without modifications. If your door trim opening measures less than 68" wide, the top and bottom tracks will require cutting.
Slide sill plate assembly onto bottom track. Sill Plate Assembly Bottom Track Do not deploy screen until it is assembled to doorway. Insert the other end of the tracks into the latch hook housing. STEP 2 INSERT SCREEN Place screen assembly onto door sill and lift into place. Flush and short sill – Assembly rests in a position where top of track is flush with edge of sill. Long sill – Assembly rests in a position on top of sill.
Extend housings to the left and right evenly until snug to the door inside trim. STEP 3 SECURE SCREEN Insert a housing screw into the pre-drilled screw hole at the top of the housing flanges on both sides to hold frame in place. Do not tighten completely. Center sill plate assembly on the door sill. Slide sill plate assembly extenders to each side to fill gaps. Center sill plate assembly on the door sill. Slide sill plate assembly extenders to each side to fill gaps.
Tighten the top screw and insert housing screws into all remaining pre-drilled holes on each vertical housing flange (2 total per side). Tighten all screws. Deploy slider bar with latch hook until it reaches the middle of the track. Mark the position of the slide bolts on the sill and top molding. Release the slider bar and drill 1/4" holes in the sill and the top molding. Deploy the slider bar with latch hook to the middle of the track. Drop slide bolts into these top and bottom holes.
Product modification Minor modifications may be necessary to tailor the retractable screen to your application. Door trim openings that measure less than 68" will require track cutting to fit the door width. Outswing door installations require a change to the handle/lock assembly to move the lock mechanism to the inside of the home. NARROW DOOR TRACK MODIFICATION Measure your door trim opening and follow the example below to make your modifications.
Frequently Asked Questions Is maintenance required on my Brisa Retractable Screen Door? Dirt and debris should be vacuumed out of the tracks periodically. Do not use oily lubricants (like WD40) on the track as these tend to attract dirt, which can hinder the operation. If needed, occasional use of a silicone-based lubricant is acceptable.
Preguntas frecuentes ¿Requiere mantenimiento mi puerta corrediza con malla Brisa? La suciedad y los desechos se deben aspirar para retirarlos de los rieles periódicamente. No utilice lubricantes a base de aceite (como WD40) en el riel ya que estos tienden a atraer la suciedad, lo cual puede obstaculizar el funcionamiento. Si es necesario, el uso ocasional de un lubricante a base de silicona es aceptable.
Puerta que abre hacia afuera – modificación del producto Hay dos escenarios individuales que requerirán modificaciones antes de comenzar con los pasos de instalación. Las aberturas de borde de la puerta que midan menos de 68" requerirán un corte de los rieles para adecuarse al ancho de la puerta.
Ajuste los tornillos superiores e inserte los tornillos de la carcasa en los restantes orificios perforados en cada una de los bastidores verticales de la carcasa (total de 2 por lado). Ajuste todos los tornillos. Serrer la vis supérieure et insérer les vis du logement dans les trous prépercés restants sur chaque bride verticale du logement (2 par côté). Serrez les vis. Despliegue la barra corrediza (con gancho) hasta que alcance la mitad del riel.
Extienda los montantes en forma pareja a la izquierda y a la derecha hasta que se ajusten en el borde interno de la puerta. Étirez la moustiquaire de façon égale vers la gauche et la droite jusqu’à ce qu’elle se soit bien ajustée au cadre intérieur de la porte. PASO 3 ASEGURE LA MALLA Inserte un tornillo de montante en el orificio perforado previamente en la parte superior de las bridas del montante en ambos lados para que el marco quede firme en el lugar. No ajuste los tornillos completamente.
Montaje de umbral Seuil de porte en métal Slide sill plate assembly onto bottom track. Deslice el montaje de umbral sobre el riel inferior Sill Plate Assembly Slide sill plate assembly onto bottom track. Riel inferior Rail du bas Bottom Track Glissez le seuil de porte en métal sur le rail du bas Inserte los extremos planos de los rieles superior e inferior en el montante decorativo. Insérez les extrémités plates des rails du bas et du haut dans le cadre décoratif.
Proceso de montaje Estas instrucciones describen paso por paso el proceso para instalar una puerta de malla retráctil. Proceso de montaje Antes de comenzar, vuelva a leer todas las instrucciones y familiarícese con las mismas. La ayuda Estas instrucciones describen paso por el proceso para instalar una puerta de malla retráctil. de otra persona puede resultar muy útilpaso durante la instalación. Antes de comenzar, vuelva a leer todas las instrucciones y familiarícese con las mismas.
Identifique su umbral y tipo de puerta Antes de que comience a instalar su nueva puerta corrediza con malla, es importante identificar su umbral y tipo de puerta. Si tiene un umbral pequeño, probablemente necesite hacer algunas modificaciones antes de continuar con los pasos de instalación. Identifiez votre seuil et type de porte Avant de commencer l’installation de votre nouvel écran de porte rétractable, il est important d’identifier votre seuil et le type de porte.
Terminología del producto Utilice la siguiente ilustración y terminología para familiarizarse con las piezas y ubicación de la Puerta corrediza con malla Brisa. Esto le servirá para seguir las instrucciones de instalación. Terminologie du produit Utilisez l’illustration et la terminologie suivantes pour vous familiariser avec vos pièces détachées et l’emplacement de votre écran rétractable de porte Brisa. Cela sera utile pour suivre les instructions d’installation.
Una propuesta innovadora para tomar aire fresco Gracias por comprar una puerta de malla retráctil Brisa de LARSON. Asegúrese de que la puerta de malla retráctil que compró sea del tamaño adecuado para su puerta. Esta puerta de malla retráctil se adapta a puertas dobles que abren hacia adentro o hacia afuera. Une nouvelle façon de sentir l’air frais Merci d’avoir fait l’acquisition d’une porte-moustiquaire rétractable Brisa de LARSON.
BRISA Retractable Screen Door Instrucciones para la instalación de la puerta doble Instructions d’installation pour porte double PRIMERO LLÁMENOS No devuelva el producto a la tienda. Si necesita ayuda con la instalación de su malla retráctil o si desea información adicional sobre el producto, llame a nuestro departamento de atención o visite nuestro sitio en Internet en www.LARSONdoors.com. APPELEZ-NOUS D’ABORD Ne retournez pas en magasin.