Installation Instructions

ManualsBrandsLarson ManualsDoorsNatureVue™ 26" x 72" Almond Retractable Window Solar Screen

2-A Recess Installation 2-B Surface Installation

VERTICAL PULL-DOWN RETRACTABLE WINDOW SCREEN

INSTALLATION INSTRUCTIONS

NATURE VUE

MOUNTING OPTIONS

1-A Recess Installation : Mount the A-Screen Cassette using K-Recess

Mounting Clips inside the window frame. Recess Installations are the

most common.

1-B Surface Installation : Surface / Flush Mount the A-Screen Cassette

using L-Surface Mount Clips.

MEASURING

Measure the opening width and height in several places and record the smallest

width and height measurement [2-A or 2-B].

INSTALLATION PREP

INSTALLATION TOOLS

L L

1-A Recess Installation

1-B Surface Installation

PHILLIPS SCREWDRIVER

MEASURING TAPE

HAND-HELD OR

POWER SAW

POWER DRILL & BITS SOFT MALLET

Head

Sill

Height (H)

Width (W)

RECORD

W________________

H________________

Head

Sill

Height (H)

Width (W)

RECORD

W________________

H________________

Window

Screen Cassette

IT IS HIGHLY RECOMMENDED THAT THE INSTRUCTIONS BE READ THROUGH BEFORE INSTALLING WINDOW.

Use saw

blade suitable

for cutting

aluminum.

202220700-1115

Summary of content (6 pages)

PAGE 1
202220700-1115 NATURE VUE VERTICAL PULL-DOWN RETRACTABLE WINDOW SCREEN INSTALLATION INSTRUCTIONS IT IS HIGHLY RECOMMENDED THAT THE INSTRUCTIONS BE READ THROUGH BEFORE INSTALLING WINDOW. INSTALLATION TOOLS PHILLIPS SCREWDRIVER MEASURING TAPE HAND-HELD OR POWER SAW POWER DRILL & BITS SOFT MALLET Use saw blade suitable for cutting aluminum.
PAGE 2
PA G E 2 N AT U R E V U E I N S TA L L AT I O N I N S T R U C T I O N S L L A B - SURFACE Installation F K G E K M N J A N D B H G These screws for B-Surface Installation only.
PAGE 3
N AT U R E V U E I N S TA L L AT I O N I N S T R U C T I O N S 3 PA G E 3 CUTTING THE CASSETTE Notice that the A-Screen Cassette has two removable stickers labeled “Begin Measuring From This End” (Side A), and another labeled “Cut This End” (Side B). Starting from Side “A”, mark your required dimension, then subtract 3/8”(9.5mm) from Step 2 width measurements. ________ (W) – 3/8" = ________ The 3/8” (9.5mm) deduction is an allowance for the G-Cassette End Cap with E-Brake that you will install in STEP 5.
PAGE 4
N AT U R E V U E I N S TA L L AT I O N I N S T R U C T I O N S 6 END CAP ASSEMBLY PA G E 4 CONT. The E-Brake, F-Bushing and G-Cassette End Cap come pre-assembled. F E A G Make sure that the long tooth on the F-Bushing and E-Brake line up with one of the slots inside the Screen Tube. Both the E-Brake and the F-Bushing must be fully inserted into the Screen Tube before the G-End Cap can be properly seated. Slip the F-Bushing down the coiled spring to the E-Brake.
PAGE 5
N AT U R E V U E I N S TA L L AT I O N I N S T R U C T I O N S PA G E 5 INSTALLATION NOTE: It is critical that the Screen Cassette and Rails be installed square 9-A Recess Installation and plumb in the door opening. Apply shims (not supplied) as needed. 9 INSTALLING THE CASSETTE 9-A Recess Installation : Use J-#8 x 3/4”(19mm) Phillips Panhead Screws to install K-Recess Mount Clips to the door frame approx. 4” in from each side. Snap only the A-Screen Cassette into the Mount Clips.
PAGE 6
N AT U R E V U E I N S TA L L AT I O N I N S T R U C T I O N S PA G E 6 OPERATION OF THE SCREEN The internal lock mechanism will automatically catch once the rollerscreen is fully extended. To retract the screen, nudge the I-Pull Handle inwards slightly to release the lock. Tilt handle inward until latch releases, then raise. WARNING: Please use eye protection when cutting and installing your screen. This is not a safety or security screen.