029.
ZipLevel ENGLISH
ZipLevel Professional precision altimeter The ZipLevel is a professional altimeter which enables you to scale and level on your own also around corners with accuracy within 3 mm. You have a working area up to + 6 m vertical and up to 70 m, respectively 50 m (with ZipLevel 25) in diameter. The digital measuring module shows all your measurements and is easy to operate. The extremely sturdy measurement cable with patented gas-liquid-system reliably works from -30 °C up to +70 °C.
ZipLevel J I H G A B C D E F G H Cable reel Securing points Measurement line Measuring module Battery compartment (back) Room for measuring module Pocket for operation manual Protective cap Backside: I Sensing device (ZipLevel Pro 35) J Ground spikes (ZipLevel Pro 35) F A B E D C Inserting batteries into the measuring module: •O pen the battery compartment (E) and insert the batteries according to the installation symbol. Pay attention to the correct polarity.
ZipLevel Console: The keys HOLD and ON/OFF react instantaneously, all the other keys have to be pressed for 2 seconds in order to activate or deactivate the particular function. The functions are also fitted with audible signals (clicking and bleeping) which makes it easier to work overhead or in non visible areas. Important: The ZipLevel memorizes the last accomplished function. When you turn the instrument on again and intend to leave the function, press the accordant key for 2 seconds.
ZipLevel Quick start of the ZipLevel Open the bottom protective cap of the basic unit and remove the measuring module. Lay the basic unit on the floor with the back facing down. Slowly pull a sufficient length of line off the cable reel. The altitude will be transferred from the basic unit to the measuring module. Switch the measuring module on with the ON/OFF-key and put the unit with its back or base on the required place of reference. When the display is ready, you will hear 2 short audible bleeps.
ZipLevel Quick start of the ZipLevel Give a place of reference to the measuring module (press ZERO-key) and move it to a different height. The appliance shows the difference in height between the place of reference and the measuring point. Now you can hold the appliance against any point and it always shows you the current height towards the place of reference. Always use the measuring module with the side, which was used to set ZERO.
ZipLevel Keys and functions ON/OFF With this key you switch the unit on and off. If no key has been pressed or the measuring module has not been moved within 4 minutes, the unit will switch itself off automatically. After 3 minutes without any activity the unit will sound a warning by giving 2 long bleeps. HOLD The HOLD-function is used where you have problems reading the display or where you intend to keep the measured data. The function can be switched on and off by shortly pressing the HOLD-key.
ZipLevel Examples for the HOLD-function: 2. Press HOLD 1. ZERO ZERO Press the ZERO-key for 2 seconds in order to make the present height (location of the measuring module) the point of reference.
ZipLevel SCALE With this you choose the required measurements in millimetres, centimetres or meters. Press the SCALE-key for 2 seconds and hold. Now the gauges the bottom right of the display will change. Release the key once the required measurement appears. The measurement for millimetres is not indicated, cm and m appear on the display. RES The ZipLevel is featured with a choice of 3 display accuracies. Press the RES-key for 2 seconds and keep it pressed in order to choose the required resolution.
ZipLevel REC The ZipLevel can also be used for different calculations and shows an average, minimum and maximum. 1) P ress the REC-key for 2 seconds. The word ‘REC’ appears on the left side of the display. 2) S tabilize the measuring module on the first measuring point and shortly press HOLD to keep the data. After that you hear a series of bleeps. Wait until these are finished before you move the module to the next measuring point.
ZipLevel MARK With the MARK-function you can produce tones to indicate the following states: a) a chosen height, b) height within a defined scope or c) height beyond a defined scope. 1) Start of this function: Get the measuring module into the required height and press the MARK-key for 2 seconds. Keep the unit steady until double lines for the scope are blinking on the display and choose a), b) or c). a) Produce a tone at a chosen height: Shortly press MARK and keep the unit steady to set up the tone.
ZipLevel Define scopes: a) Tone at a certain height: for accurate levelling MARK Tone b) Tone within a scope: for less accurate levelling No tone Scope Tone No tone MARK c) Tone beyoned a scope: for rough levelling Continuous tone MARK Scope No tone Bleeping tone ENGLISH 13
ZipLevel CAL The appliance has been calibrated at the factory. Please only calibrate, in case the measuring results are wrong or the letters ‘CAL’ are blinking on the display. A benchmark of 1.219 m above the base unit is important for the gauging. It will be best to use the sensing device to gauge the appliance (only with ZipLevel Pro 35). Calibrating the ZipLevel: 1) Put the basic unit on its back onto a level surface and switch the measuring module on.
ZipLevel Calibration in 3 steps: Step 1: Lay the measuring module on its base or back next to the basic unit and press the CAL-key again. (0) is blinking on the display. Step 2: Press CAL again. (121.9) is blinking on the display. Step 3: Lift to a height of 1.219 m and press CAL again. Hold steadily during the process. Then (121.9) is shown on the display.
ZipLevel ADDER (add): To carry out accurate measurements indoors, the ADDER-function automatically adds the height, respectively thickness of the measuring module on the measured data. Advice about the protective cover (only with ZipLevel Pro 35): You need to state whether you are working with or without protective cover (‘Boot on’/’Boot off’). Press HOLD to keep the data. Then press CAL-key for 2 seconds and hold. Display alternately shows ‘bon’ and ‘boff’. Release at either ‘Boot on’ or ‘Boot off’.
ZipLevel „Boot on“ / „Boot off“: HOLD CAL Choose „Boot on“ or „Boot off“! 2 seconds ADDER-function: 3. 3. MARK REC + Height + + Thickness 8,8 cm or 9,4 cm with cover 2. + 5 cm or 5,6 cm with cover 2. HOLD HOLD 1. 1.
ZipLevel TIPS FOR USERS 1) Check the point of reference often when carrying out critical/serious levelling jobs or press ZERO often at the point of reference. (CAL is not necessary for levelling!) Hold the height differences between line, basic unit and measuring module as low as possible. 2) If possible, avoid high differences in temperature between line and measuring module (e.g. sun and shade). 3) Avoid unnecessary kinks over objects.
ZipLevel Technical facts Vertical measuring range 12 m (6 m over and under the basic unit) Horizontal measuring range + 35 m ZipLevel Pro 35 (70 m Ø) + 25 m ZipLevel 25 (50 m Ø) Levelling precision 3 mm Height-measuring accuracy 0,2 % of the shown data up to 3 m, resp.
ZipLevel Service- and shipping address: Umarex GmbH & Co. KG – Laserliner – Möhnestraße 149, D-59755 Arnsberg, Germany Tel.: +49 2932 638-300, Fax: -333 laserliner@umarex.com UMAREX GmbH & Co. KG – Laserliner – Donnerfeld 2 D-59757 Arnsberg, Germany Tel.: +49 2932 638-300, Fax: -333 www.laserliner.